Related Manuals for Lumberjack TS254PL
Summary of Contents for Lumberjack TS254PL
- Page 1 SAFETY AND OPERATING MANUAL TABLE SAW WITH DUST EXTRACTOR TS254PL ORIGINAL INSTRUCTIONS TS254PL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratulations on your purchase. Before using the Product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. TS254PL... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. TS254PL...
- Page 5 Always adjust the blade guard in such a materials listed under Intended Use. manner that the face is loosely against the Otherwise, the machine can be subject to work piece when sawing. Never clamp the overload. blade guard when it is open. TS254PL...
- Page 6 9.5. When using a cable reel, always unwind the authorised customer service agent. Replace damaged extension cables. cable completely. This will ensure that the safety of the power tool is maintained. TS254PL...
-
Page 7: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 TS254PL TS254PL... -
Page 8: Machine Details And Product Features
The capacity of the power tool is designed for sawing hardwood and Rip Fence Integrated Folding Stand softwood. The power tool is not suitable for cutting aluminium or other non‐ferrous metals Push Stick or alloys. TS254PL TS254PL... -
Page 9: Assembly
Install the handle assembly ‐ Place the nut from the handle into the recess at the back of the hand wheel. ‐ Screw the handle in place, and then place the end cap on. TS254PL... - Page 10 ‐ The stand has height adjustment on the before proceeding. bottom of each leg to make sure you can get the saw level for cutting. Reverse these instructions to set the machine in transport mode. TS254PL...
-
Page 11: Operation
‐ This is set by pulling the table locking lever, the Height adjustment handle. setting the desired length then relocking the lever. ‐ The blade angle is adjusted by unlocking the bevel lock, setting the position by turning the inside handle, and then relocking the lock. TS254PL... -
Page 12: Maintenance And Service
‐ Remove the Nut, Washer and blade. two screws shown above. ‐ Before replacing the blade with a new one make sure to clean the washer and arbor shaft, this will ensure a correct seating of the new blade. TS254PL... - Page 13 ‐ Remove the Nut, Washer and blade. two screws shown above. ‐ Before replacing the blade with a new one make sure to clean the washer and arbor shaft, this will ensure a correct seating of the new blade. TS254PL...
-
Page 14: Troubleshooting
TROUBLESHOOTING TS254PL... -
Page 15: Lumberjack Guarantee
1.2.7 The product has not been used for 1.2.3 If asked to do so by lumberjack or hire purposes. its Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by... - Page 16 2.4 Please note that it is essential that the letter of 2. Claims Procedure claim reaches Lumberjack on the last day of this 2.1 In the first instance please contact the guarantee at the latest. Late claims will not be Authorised Dealer who supplied the product to considered.
-
Page 17: Declaration Of Conformity
TS254PL... -
Page 18: Parts List
PARTS LIST TS254PL... - Page 19 PARTS LIST TS254PL...
- Page 20 PARTS LIST TS254PL...
- Page 21 PARTS LIST TS254PL...
- Page 22 PARTS LIST TS254PL...
- Page 23 PARTS LIST TS254PL...
- Page 24 PARTS LIST TS254PL...
-
Page 25: Parts Diagram
PARTS DIAGRAM PART 1 TS254PL... - Page 26 PARTS DIAGRAM PART 2 TS254PL...
- Page 27 PARTS DIAGRAM FULL TS254PL...
Need help?
Do you have a question about the TS254PL and is the answer not in the manual?
Questions and answers