Download
Share
Print this page
  1. Manuals
  2. Brands
  3. QualGear Manuals
  4. TV Mount
  5. QG-TM-032-BLK
  6. Installation manual

QualGear QG-TM-032-BLK Installation Manual

Heavy duty full motion tv wall mount
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Make sure the TV is safely secured before releasing
IMPORTANT:
Padlock is not
included
B
Safety Bar
Put a padlock on the safety bar to prevent the TV from being stolen.
Adjustments
6
Tilt -10°~+5°
Level -4°~+4°
Adjust to the desired position
by tilting -10°~+5°, swiveling
-90°~+90° , -180°~+180° , -90°~+90°
at three pivot points and by
leveling -4°~+4°.
;
Scan the QR Code™ below
for more info about this product:
Version April 2018
Version April 2018
QG-TM-032-BLK
`Lorem ipsum
For Most 37" to 70" Flat Panel and
70
Curved TVs
40kg
40kg
Do not exceed the maximum rated weight
(88lbs)
(88lbs)
specified. Otherwise, serious injury or
property damage may occur.
2 0 0 x 2 0 0 | 3 0 0 x 2 0 0 | 3 0 0 x 3 0 0
4 0 0 x 2 0 0 | 4 0 0 x 3 0 0 | 4 0 0 x 4 0 0
6 0 0 x 2 0 0 | 6 0 0 x 3 0 0 | 6 0 0 x 4 0 0

Advertisement

loading

Related Manuals for QualGear QG-TM-032-BLK

Summary of Contents for QualGear QG-TM-032-BLK

  • Page 1 Make sure the TV is safely secured before releasing IMPORTANT: QG-TM-032-BLK `Lorem ipsum Padlock is not included Safety Bar Put a padlock on the safety bar to prevent the TV from being stolen. Adjustments Tilt -10°~+5° Adjust to the desired position by tilting -10°~+5°, swiveling...

  • Page 2: Parts Checklist

    Before starting installation, please check that all parts shown in this checklist IMPORTANT: are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and installation WARNING until you receive all the parts.
  • Page 3 Installing the Decorative Covers 65mm 65mm (2.5") (2.5") When decorative covers are installed correctly, ø 4.5mm there will be a gap between the bottom of the wall NOTE (ø 3/16") plate and the decorative covers. This gap is for the safety bar installation on Step 5.
  • Page 4 Mounting to a Concrete Wall NOTE Do NOT use power drill and do NOT over tighten the lag bolts. Marking Template Wall Mount 2-B LK QG -TM -03 3 Place concrete anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer. Using a socket wrench, mount the wall mount (A) and fasten them with the provided lag bolts Hold the marking template (H) provided against the wall where you want to install the TV, (W-A) and D6 washers (W-C).

  • Page 5: Back Panel

    Installing to a Curved or Recessed Back Panel of a TV Choose the appropriate screws and washers according to the type of your TV, and attach adapter brackets (C and D) to the back of the TV using a Phillips screwdriver. IMPORTANT! Tighten all screws but do NOT over tighten...
  • Page 6 IMPORTANT! Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your Antiskid Block Tighten all screws but do T V and attach adapter brackets (C and D) to the back of the TV using a Phillips screwdriver. NOT over tighten M-D/ M-E/ M-F Tighten screws on the antiskid blocks using a proper...