Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron CNXFZ
Summary of Contents for Crestron CNXFZ
-
Page 3: Table Of Contents
Crestron CNXFZ Contents CNX Focus/Zoom Control Interface: CNXFZ Description... 1 Functional Description ... 1 Physical Description... 2 Leading Specifications... 6 Setup ... 7 Network Wiring... 7 Hookup ... 8 Identity Code ... 8 SIMPL™ Windows Programming ... 9 How the Program Works ... 10 How to Create the Program ... -
Page 5: Cnx Focus/Zoom Control Interface: Cnxfz
Four supplied jumper boards permit the support of any lens assembly requiring an input voltage in the range of +/-2.5 to +/- 12 VDC. Thus a single CNXFZ with its four jumpers can control nearly any lens in the industry. Refer to the table below for exact voltage outputs for each jumper board. -
Page 6: Physical Description
Physical Description The CNXFZ, shown below, is housed in a black enclosure with a silk-screened front label. All electrical connections, except for the network (NET), are made to the front panel. Also on the front panel, there are three LEDs and five buttons. All of these front panel features are discussed in subsequent paragraphs. - Page 7 Crestron CNXFZ CNXFZ Ports A number of ports bearing silk-screened labels are located on the CNXFZ. Refer to the illustration and descriptions after this paragraph. CNXFZ Front Panel This 6-pin, 6-position RJ11 modular jack is used to connect the CNXFZ to the control system.
- Page 8 Focus/Zoom Control Interface CNXFZ Pinout for LENS Port Wiring Diagram for Lens A, B, and D (+/-12V, +/-8V, and +/-6V) 4 • CNX Focus/Zoom Control Interface: CNXFZ DESCRIPTION Focus Out Focus Common Zoom Out Zoom Common Rate/Position Mode 5V Reference from Lens 7.5V Reference from Lens...
- Page 9 ZOOM_FEEDBACK FOCUS_FEEDBACK ANALOG_GROUND DESCRIPTION Rx (to CNXFZ) Input Tx (from CNXFZ) Output RTS (from CNXFZ) Output CTS (to CNXFZ) Input CNX Focus/Zoom Control Interface: CNXFZ • 5 Focus/Zoom Control Interface HIROSE LENSE CONNECTOR FOCUS_MOTOR FOCUS CONTROL POWER_GND GROUND ZOOM_MOTOR ZOOM CONTROL...
-
Page 10: Leading Specifications
Function not defined at time of printing. LED installed for future use. CNXFZ Buttons Five buttons are located on the CNXFZ front panel. The purpose of these buttons is to permit local manual operation of lens focus and zoom functions when installing the unit. -
Page 11: Setup
PF = Power factor of entire run (or chain). RESISTANCE (R) WIRE GAUGE Doubled CAT5 Tripled CAT5 CNX Focus/Zoom Control Interface: CNXFZ • 7 DETAILS Height: 5.50 in (13.97 cm) Width: 3.50 in (8.89 cm) Depth: 1.31 in (3.34 cm) -
Page 12: Hookup
(NET ID). These codes are recognized by a two-digit hexadecimal number from 03 to FE. The NET ID of the unit must match an identity code specified in the SIMPL 8 • CNX Focus/Zoom Control Interface: CNXFZ Crestron CNXFZ CNXFZ... -
Page 13: Simpl™ Windows Programming
Crestron CNXFZ Windows program. The NET ID of each CNXFZ has been factory set to 40, but may be changed from the PC via VT Pro or SIMPL Windows. The method for changing the unit’s NET ID is identical regardless of the software chosen. -
Page 14: How The Program Works
How the Program Works A basic CNXFZ SIMPL program is shown on the next page in block diagram form. For this example, the SIMPL Windows program controls the CNXFZ through the use of nine analog signals. -
Page 15: How To Create The Program
CNXFZ. Two position drive signals, FOC_SET and ZOOM_SET, are used to instruct the CNXFZ to drive the camera to a preset position. Anytime the analog level on one of these drive signals change, the CNXFZ adjusts the corresponding focus/zoom lens position until the feedback matches the level at the programmed output. - Page 16 System View of the CT-3000 in SIMPL Windows’ Configuration Manager Also add the CNXFZ to the system. Drag and drop the CNXFZ from the Network Control Modules folder into Slot #9 on the CNMSX-PRO. Verify that the NET ID is set to 40, shown below.
- Page 17 Detail View of the Analog Signals for the CT-3000 in SIMPL Windows’ Programming Manager Also from the Network Modules folder, double click on the CNXFZ and the Port A: CNXFZ Lens Controller Driver icons for a detail view (alternatively CTRL+D or drag and drop into Detail View).
- Page 18 Focus/Zoom Control Interface Detail View of the Signals for the CNXFZ in SIMPL Windows’ Programming Manager Two logic symbols are necessary for this SIMPL Windows program. They must be added from Logic Symbols folder (Symbol Library) in the Programming Manager workspace.
-
Page 19: Application For An Alternate Method Of Control
This alternate method of control utilizes the VT-3500 and a program for the CNMSX-PRO using the CNXFZ network control module. This example program actually offers two methods of control in one program. In CNXFZ.VTP, there are two pages (Main with buttons and Main with slider). Each represents a different user implementation. -
Page 20: Problem Solving
Without feedback, lens presets cannot be achieved in rate mode. Some lenses can switch between rate and position mode; the CNXFZ provides the appropriate connections to facilitate this. This type of lens can achieve presets without feedback. -
Page 21: Return And Warranty Policies
All brand names, product names, and trademarks are the sole property of their respective owners. Windows is a registered trademark of Microsoft Corporation. Windows95/98/Me/XP and WindowsNT/2000 are trademarks of Microsoft Corporation Operations Guide - DOC. 5753 Focus/Zoom Control Interface CNX Focus/Zoom Control Interface: CNXFZ • 17... -
Page 22: Appendix: Application Examples
The application examples in this appendix suggest the lens cabling connection for the lens type jumper (A through D) to be used for a given camera lens. The camera lens pins are listed in the left-most column. The CNXFZ LENS connector pins are listed in the right-most column. -
Page 23: Lens Cabling Connection For Jumper B (+/-8V)
Iris Speed/Pos Sig Signal Common +V1(+7.5V) Iris Control Iris Mode (Local/Camera) Lens Common Focus Motor Drive Feedback Supply Focus Feedback Feedback Ground Zoom Motor Drive Zoom Feedback Ground CNX Focus/Zoom Control Interface: CNXFZ • 19 FOCUS ZOOM 2,4,10 FOCUS ZOOM...