Related Manuals for ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni + Inox
Summary of Contents for ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni + Inox
- Page 1 EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni + Inox GPU WATER BLOCK EAN: 3831109903971 USER GUIDE...
- Page 2 Before you start using this product, please follow these basic guidelines: Carefully read the manual before beginning with the installation process. Remove your graphics card from the computer for the safest mounting process to prevent any possible damage to your GPU or its circuit board (PCB).
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS PREPARING YOUR GRAPHICS CARD CUTTING AND PLACING THERMAL PADS REMOVING THE STOCK COOLER CLEANING THE PCB APPLYING THERMAL COMPOUND INSTALLING THE WATER BLOCK PLACING THE BLOCK ON THE GRAPHICS CARD ATTACHING THE BACKPLATE CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES INSERTING THE GRAPHICS CARD INTO THE CHASSIS... -
Page 4: Box Contents
BOX CONTENTS 088-Mounting Trinity RTX 4090 Note: There are additional screws in the mounting kit. Screw M2.5 x 4 AX1 (12x) Screw M2.5 x 7 AX1 (10x) 9047 9049 Washer POLYAMID M2.5 0.5mm Thermal Grizzly Hydronaut (1g) (9x) 8623 EK-Pro GPU WB AMP-Trinity RTX 4090 Ni+Inox (1x) Zotac RTX Pro Backplate (1x) Thermal PAD F 1.0 mm - (120 x 16 mm) -
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 15.6 mm 234.5 mm 245.9 mm 23.2 mm 32.5 mm 87.1 mm 135.7 mm - 5 -... -
Page 6: Technical Specifications And Water Block Parts
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS Position Description Quantity 106474 088 - baker - Zotac RTX 4090 Pro Coldplate TT (Ni) 106133 TOP Plexi - Vector Insert R5 106475 088 - kovina - Zotac RTX 4090 Pro top TT 103089 vijak M3 x 5 ISO 14581 TX INOX 103988 Distancer M4-M2.5 x 3 mm Vector... -
Page 7: Preparing Your Graphics Card
PREPARING YOUR GRAPHICS CARD STEP 1 REMOVING THE STOCK COOLER Place your graphics card on the flat surface and carefully remove the stock cooler. Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps in order to install the EK-Pro GPU WB AMP/Trinity RTX 4090 - Ni + Inox water block onto the graphics card. -
Page 8: Applying Thermal Compound
APPLYING THERMAL COMPOUND Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS. The excessive or uneven application of thermal grease may lead to poor performance! For this step, you will need:... -
Page 9: Installing The Water Block
INSTALLING THE WATER BLOCK STEP 1 M2.5 x 4 AX1 SCREW PLACING THE BLOCK ON THE GRAPHICS CARD M2.5 POLYAMID This procedure is the same for all full-cover water blocks. Carefully WASHER position the water block with preinstalled standoffs on the graphics card. -
Page 10: Attaching The Backplate
Check whether the water block makes contact with the intended integrated circuit. Then repeat Steps from the previous section to re-attach the block. In case you fail to obtain good contact, please check again or contact our support service at https://www.ekwb.com/customer-support/. - 10 -... -
Page 11: Inserting The Graphics Card Into The Chassis
INSERTING THE GRAPHICS CARD INTO THE CHASSIS Carefully lift your graphics card with the installed water block and insert it into your PC’s motherboard PCI express expansion slot. Please keep in mind that your graphics card is heavier than before it was equipped with the water block. -
Page 12: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.
Need help?
Do you have a question about the EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni + Inox and is the answer not in the manual?
Questions and answers