Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BWT pro-soft 11
Summary of Contents for BWT pro-soft 11
- Page 1 BWT pro-soft 11 Fitting and operating instructions...
-
Page 2: Table Of Contents
5.4 Disposal and environmental informations ................14 Chapter 6: Fault inding ........................15 6.1 Trouble shooting Guide ....................... 15 Chapter 7: Technical data ........................17 7.1 Technical data of BWT pro-soft 11 ..................17 EC declaration of incorporation ......................18... -
Page 3: Chapter 1: Introduction
E-mail: info@bwt-uk.co.uk Additional information for the operator. 1.4 Intended use The application BWT pro-soft 11 is designed for softening or partially softening domestic water (in accordance with the relevant regulations e.g. for drinking water). All other use is strictly forbidden and... -
Page 4: Scope Of Delivery
1.5 Scope of delivery BWT pro-soft 11 water softer with: Standard delivery: 1. Multi-way control valve with microprocessor controller 2. Blending valve 3. Softening column with ion exchange resin 4. Softened water outlet 5. Hard water inlet 6. Drain water 7. -
Page 5: Chapter 2: Quick Operation
Depending on the internal settings of the unit Regeneration time: free input at RECHARGE TONIGHT Hardness of drinking water / capacity: 300 ppm, 1566 litres for 10 litre model BWT pro-soft 11 Standard Display Operating range UK/EU 1.7 ... 5.0 bar 1.0 ... -
Page 6: Programming Procedure
2.3 Programming procedure 2. Setting the water hardness (see Fig. 2) The display default is 300 ppm (typical hardness le- vel) which indicates a setting suitable for hard water with a value of 300 parts per million of hardness minerals. Use the keys [UP] [DOWN] keys to adjust the setting to match that of the one you obtained / identified earlier. -
Page 7: Chapter 3: Installation
3. Installation Inlet- and outlet connections: When installing the unit, select a location where the 3.1 Installation requirements unit can easily be connected to the water supply net- work. A connection to the waste water system (at National guidelines and regulations: least DN 50), a floor drain and a separate mains Observe all applicable installation regulations, ge- socket (see technical data) must be nearby. -
Page 8: Installation And Operation Considerations
Please check connections and pipeline junctions for 3.3 Installation and operation considerations leaks. 1. Before you begin Handing over the unit to the operator: The installation of your new water softener is rela- If there is a delay between the installation/startup tively straightforward. - Page 9 It is re- of the time-clock operation is listed in the last column. commended that an anti vacuum valve be fitted to the inlet pipework supplying the water softener. BWT pro-soft 11 10 litres M3/°F (50) 4.
-
Page 10: Installation Layout
3.4 Installation Layout ) water inlet = hard water = drinking water ) outlet with softened water To rising Inlet from Non-return By-pass valve main mains valve shown closed Outlet valve Inlet valve shown open shown open Use reducing bush for 15mm pipework Outlet from Inlet to... -
Page 11: Technical Overview Of Device
3.5 Technical overview of device: Inlet connection (feed water) for flexible hose, with thread ¾“ Outlet connection (softened water) for flexible hose, with thread ¾“ G1. Brine storage cabinet salt filling G2. Connection to brine internal connection O. -
Page 12: Installing Your Softener
3.6 Installing your softener If the water softener is fitted in a cellar or basement, 1. Positioning the water softener: the overflow can be run to a storage tank. Do not It is very important to establish the water pressure elevate the overflow hose. -
Page 13: Chapter 4: Operation
4. Operation Shake the bottle in between and keep adding tablets to the water until the solution turns from 4.1 Functions and features wine red to blue, record the number of tablets as you go. Capacity requirement-dependent of the unit Using the data table supplied with your kit, controller: match up the number of tablets with the hard-... - Page 14 Charge Bar: Adding regenerative salt: Refill the salt no later than when SALt is indicated Having set the display on the control facia, you will notice that during normal operation there is a char- on the display or the current filling is 15cm above ge bar running along the bottom of the display.
-
Page 15: Setting The Hardness Of Blended Water
5.4 Disposal and environmental informations Check the regenerative and refill after use. At the end of product life please contact BWT Cus- tomer Services to arrange a new replacement for Check the water hardness: The hardness of drinking your softener. -
Page 16: Chapter 6: Fault Inding
6. Fault finding 6.1 Trouble shooting Guide Attention: If your water softener is not performing as it should, please run through the check list below. Checklist: Solution: Page: Problem: Water still remains hard. Is there a minimum of 150mm of salt in Fill the brine cabinet with salt. - Page 17 Attention: If your water softener is not performing as it should, please run through the check list below. Checklist: Solution: Page: Problem: Water runs from the drain constantly. Is the unit in recharge mode? If yes, this is normal, wait until the recharge is complete.
-
Page 18: Chapter 7: Technical Data
7. Technical data 7.1 BWT pro-soft 11 BWT pro-soft Type Nominal connection (outside thread) ¾“ (DN 20) Nominal flow rate in accordance with EN 14743 1440 Operating pressure EU (min./max.) 1.0 / 8.0 Operating pressure UK (min./max.) 1.7 / 5.0... -
Page 19: Ec Declaration Of Incorporation
Guideline for electromagnetic compatibility (EMC) Note: Do not perform any changes, extension and reconstruction work on the device which might impair safety without the approval of BWT water + more GmbH, otherwise this declaration loses its validity. Note: Please ensure that all conditions of the installation preconditions are met! Manufacturer: BWT UK Ltd., Coronation Road, Buckinghamshire, HP12, 3SUH... - Page 20 BWT – For You and Planet Blue signifies our mission to take ecological, economic and social responsibility, and to provide our customers with the best products, systems, technologies and services in all areas of water treatment, while making a valuable contribution to the preservation of our blue planet’s global resources.
Need help?
Do you have a question about the pro-soft 11 and is the answer not in the manual?
Questions and answers