Table of Contents
Advertisement
Quick Links
1.
SETUP FOR INSTALLATION OF QMC-DCP ADJUSTABLE RACK MOUNTS................1
1.1.
GETTING STARTED................................................................................................................ 1
2.
REMOVING PROTECTIVE COVERS.................................................................................2
3.
INSTALLING THE ADJUSTABLE MOUNTS .....................................................................4
3.1.
STEP 1: INSTALLING THE TOP GUIDES TO THE RIGHT AND LEFT SIDE........................ 4
3.2.
STEP 2: INSTALLING THE BOTTOM GUIDES ...................................................................... 6
3.3.
STEP 3: COMPLETING THE ASSEMBLY .............................................................................. 8
Tables
Table 1-1: Parts List............................................................................................................................. 1
Figures
Figure 1-1: Parts in the QMC-DCP-RP Accessory Kit ......................................................................... 1
Figure 2-1: Protective Cover on QMC-DCP ......................................................................................... 2
Figure 2-2: Remove the Protective Covering from the Right Side ....................................................... 2
Figure 2-3: Remove the Protective Covering from the Left Side.......................................................... 3
Figure 2-4: Protective Cover removed from the QMC-DCP................................................................. 3
Figure 3-1: Attaching the Top Guide Rotation Lock - Right Side ........................................................ 4
Figure 3-2: Securing the Top Guide Rotation Lock - Right Side ......................................................... 5
Figure 3-3: Attaching the Top Guide Rotation Lock - Left Side........................................................... 5
Figure 3-4: Securing the Top Guide Rotation Lock - Right Side ......................................................... 6
Figure 3-5: Bottom Guide with mounting holes .................................................................................... 7
Figure 3-6: Bottom Guide position in respect to Top Guide (not installed) .......................................... 7
Figure 3-7: Bottom Guide position in respect to Top Guide (installed) ................................................ 8
Figure 3-8: Adjusting and securing the angle....................................................................................... 8
Installation Guide for the QMC-DCP-RP
TABLE OF CONTENTS
Revision 1.0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for evertz QMC-DCP-RP
Summary of Contents for evertz QMC-DCP-RP
-
Page 1: Table Of Contents
Tables Table 1-1: Parts List..........................1 Figures Figure 1-1: Parts in the QMC-DCP-RP Accessory Kit ................. 1 Figure 2-1: Protective Cover on QMC-DCP ..................2 Figure 2-2: Remove the Protective Covering from the Right Side ............2 Figure 2-3: Remove the Protective Covering from the Left Side............3 Figure 2-4: Protective Cover removed from the QMC-DCP.............. - Page 2 Evertz products are for informational use only and are not warranties of future performance, either express or implied. The only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
-
Page 3: Setup For Installation Of Qmc-Dcp Adjustable Rack Mounts
SETUP FOR INSTALLATION OF QMC-DCP ADJUSTABLE RACK MOUNTS The QMC-DCP-RP is an accessory kit for the QMC Desktop Control Panel (QMC-DCP). The QMC- DCP-RP accessory kit allows the user to adjust the angle of the QMC-DCP when it is installed in a desk or rack. -
Page 4: Removing Protective Covers
Installation Guide for the QMC-DCP-RP REMOVING PROTECTIVE COVERS The QMC-DCP is shipped with protective covering on the mounting braces. These covers can be removed by unscrewing the screws, as shown in Figure 2-1. This step is repeated for both the right and left side of the QMC-DCP. -
Page 5: Figure 2-3: Remove The Protective Covering From The Left Side
Installation Guide for the QMC-DCP-RP Figure 2-3: Remove the Protective Covering from the Left Side Figure 2-4 shows the QMC-DCP with both protective covers removed. Figure 2-4: Protective Cover removed from the QMC-DCP Page 3 Revision 1.0... -
Page 6: Installing The Adjustable Mounts
Installation Guide for the QMC-DCP-RP INSTALLING THE ADJUSTABLE MOUNTS The QMC-DCP-RP accessory kit has two major parts: The Top Guides (right and left) and the Bottom Guides. The right and left Top Guides are fastened on the QMC-DCP panel itself and the Bottom Guides are fastened to the mounting 19”... -
Page 7: Figure 3-2: Securing The Top Guide Rotation Lock - Right Side
Installation Guide for the QMC-DCP-RP Figure 3-2: Securing the Top Guide Rotation Lock – Right Side Repeat the process for attaching the Top Guide Rotation Lock – Left Side to the mounting bracket on the left side of the QMC-DCP panel, as shown in Figure 3-3 and Figure 3-4. -
Page 8: Step 2: Installing The Bottom Guides
The Bottom Guides (Part C – see Figure 3-5) are fastened to the rack or desktop rack that the QMC- DCP is being fitted in. There are two Bottom Guides provided in the QMC-DCP-RP. These parts are bi-directional, therefore, no right or left designation is required. The Bottom Guides are fastened to the rack through the mounting holes shown in Figure 3-5. -
Page 9: Figure 3-5: Bottom Guide With Mounting Holes
Installation Guide for the QMC-DCP-RP Figure 3-5: Bottom Guide with mounting holes When installing the Bottom Guide to the rack, the user should be aware that the Bottom Guide attaches to the Top Guide with Rotation Lock, as shown in Figure 3-6 and Figure 3-7. Therefore, care MUST be taken when centering the Bottom Guide in the rack. -
Page 10: Step 3: Completing The Assembly
Installation Guide for the QMC-DCP-RP Figure 3-7: Bottom Guide position in respect to Top Guide (installed) 3.3. STEP 3: COMPLETING THE ASSEMBLY For the final step of the assembly, the user can adjust the angle of the panel using the pin connector shown in Figure 3-8.
Need help?
Do you have a question about the QMC-DCP-RP and is the answer not in the manual?
Questions and answers