Serial digital audio de-embedder and vitc to ltc translator (18 pages)
Summary of Contents for evertz 570DSK-25G Series
Page 1
Version 2.0, February 2021 The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of purchasers of the 570DSK Series Logo Inserter. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the operation of the 570DSK Series Logo Inserter.
Page 3
IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “Dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
Page 4
WARNING Changes or modifications not expressly approved by Evertz Microsystems Ltd. Could void the user’s authority to operate the equipment. Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables...
Page 5
Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
Page 6
570DSK-3G /4K-25G Logo Inserter This page left intentionally blank Page ii Revision 2.0...
Logo Inserter OVERVIEW The 570DSK-25G is a single path Downstream UHD IP Keyer with Logo insertion. As part of ‘Evertz’ Software Defined Video Networking solution, the 570DSK-25G is an IP-based downstream keyer with 25GbE I/O for HD/3G/12G with an external keyer (from Key/Fill inputs) and an internal logo keyer for animations and static logos.
& rear plates. Figure 3-1 : 570DSK-25G Rear and Front Panels 3.1.1. Front Plate The front plate of the 570DSK-25G series is equipped with 2x QSFP ports capable of passing 25GB of data per port. Page 5 Revision 2.0...
570DSK-3G 4K-25G Logo Inserter QSFP 1: This QSFP connector is the Main Program, Fill and Key input to the 570DSK(-4K)(-3G)- 25G. The Program, Preview and HD Downconvert output is also on the same connector. Below is a breakdown of each of the lanes in the QSFP: Lane 1 - Input: Program &...
570DSK-3G 4K-25G Logo Inserter QSFP 3: This QSFP connector goes to the 570HDC to provide an HD Downconvert of the Program video to the 570DSK-25G. Below is a breakdown of each of the lanes in the QSFP: Lane 1 - Input: HD Downconvert - Output: HD Downconvert Lane 2 - Input: Not used...
570DSK-3G 4K-25G Logo Inserter 3.3. CONNECTING TO AN ETHERNET NETWORK The 570DSK-25G is designed to be used with either a 1Gbe or 10Gbe network also known as Fast Ethernet, twisted pair Ethernet cabling systems. The cable must be “straight through” with a RJ-45 connector at each end.
HyperTerminal (or equivalent), the 570DSK module’s IP address and subnet are identified. The 7700 upgrade cable supplied with the 570FR frame is a multi-colored ribbon cable with a six pin header socket on one end and a female 9 pin D connector on the other end (Evertz part number This cable is normally in the vinyl pouch at the front of the manual binder.
Logo Inserter Figure 3-3 : Tera Term – Network Configuration • To save the new IP address, login again with root/evertz and type ‘reboot’. See Figure 3-4 below screenshot for reference. Figure 3-4 : Tera Term – Saving New IP Page 10 Revision 2.0...
570DSK-3G 4K-25G Logo Inserter 3.6. CONNECTING THE VIDEO 3.6.1. Video Inputs The HD or 3G or 4K program video source should be connected to QSFP 1 (Main) and QSFP 2 (Backup). The 570DSK-25G supports HD or 3G or 4K video in the formats shown in Table 3-3. The video standard must be set manually to match the incoming video type (see section 4.8 for VLPRO Configuration).
Page 20
570DSK-3G 4K-25G Logo Inserter Page left intentionally blank Page 12 Revision 2.0...
There are 3 components of SNMP: 1. An SNMP manager, also known as a Network Management System (NMS), is a computer running special software that communicates with the devices in the network. Evertz VistaLINK ® Pro Manager graphical user interface (GUI), third party or custom manager software may be used to monitor and control Evertz VistaLINK enabled fiber optic products.
570DSK-3G 4K-25G Logo Inserter 4.2. DEVICE STATUS The Device Status section enables the user to see an overview on the state of the device. Figure 4-1 : VistaLINK Pro - Device Status ® Device Status: Application Status: Shows the status of the application running in the hardware. •...
Page 24
570DSK-3G 4K-25G Logo Inserter IGMP Config: IGMP Config: Allows user to enable or disable the IGMP. By default, it is enabled. • Video Config: Video Standard: Allows user to choose the video standard for DSK to pass • Lane Config: Allows user to choose Single Lane or Multi Lane •...
570DSK-3G 4K-25G Logo Inserter 4.4. PTP CONTROL Figure 4-3 : VistaLINK Pro - PTP Control ® PTP Config: Domain Number: Allow the user to set the domain number of the PTP • Priority 1: Allows the user to set the Priority# 1 of the PTP •...
Page 26
570DSK-3G 4K-25G Logo Inserter • Mode: Allows the user to select the PT mode from IEEE-1588 or SMPTE2059 or AES67 Log Announce Interval: Allows the user to set the announce interval. Announce interval must match • with the PTP settings in PTP grandmaster clock. Log Sync Rate: Allows the user to set the Sync rate.
570DSK-3G 4K-25G Logo Inserter 4.5. QSFP Figure 4-4 : VistaLINK Pro – QSFP ® QSFP sections shows the status and power levels of each QSFP lanes in each QSFP plugged in on DSK. Page 19 Revision 2.0...
570DSK-3G 4K-25G Logo Inserter 4.6. CONTROL INTERACES The Control Interfaces section allows the user to view and set the control IP address of the DSK. It also shows the link status of each control interfaces. Figure 4-5 : VistaLINK Pro – Control Interfaces / 1G Ethernet ®...
570DSK-3G 4K-25G Logo Inserter IP Address: Allows user to view the IP address for each of the 25G lanes in QSFP. • • Netmask: Allows user to view the Netmask for each 25G lanes in a QSFP MAC Address: Allows user to view This displays the MAC address for each of the 25G lanes •...
570DSK-3G 4K-25G Logo Inserter 4.9. VIDEO OUTPUT STREAMS The Video Output Streams section shows the details of each video output stream. Figure 4-8 : VistaLINK Pro – Video Output Streams ® Output Source Configuration: Source IP: Allows user to set the source Ip address needs to be associated with multicast address. •...
570DSK-3G 4K-25G Logo Inserter 4.10. AUDIO INPUT STREAMS The Audio Input Streams section shows the details of each Audio input stream. Figure 4-9 : VistaLINK Pro - Input Audio Streams ® Program & Program Backup: Allows user to configure the audio ip input streams in program •...
570DSK-3G 4K-25G Logo Inserter 4.11. AUDIO OUTPUT STREAMS The Audio Output Streams section shows the details of each Audio output stream. Figure 4-10 : VistaLINK Pro – Audio Output Streams ® Output Audio Configuration: Program and Preview Audio Outputs: Allow user to configure main and backup of program •...
570DSK-3G 4K-25G Logo Inserter 4.12. ANC INPUT STREAMS Figure 4-11 : VistaLINK Pro – ANC Input Streams ® Input ANC Configuration: Program & Program Backup: Allows user to configure the anc ip input streams in program and • program backup section. Source IP: Allows user to set the source ip address associated with the anc multicast address.
570DSK-3G 4K-25G Logo Inserter Output ANC Configuration: Program and Preview Audio Outputs: Allow user to configure the main and backup program • and preview audio ip outputs. Source IP: Allows user to set the source ip address to be associated with the anc multicast •...
570DSK-3G 4K-25G Logo Inserter 4.15. NMOS Figure 4-14 : VistaLINK Pro – NMOS ® NMOS Configuration: Control Interface: Allows user to set the NMOS control interface for controlling the 570DSK. • Discovery Mode: Allows user to set the discovery mode to discover the device in NMOS controller. •...
570DSK-3G 4K-25G Logo Inserter 4.16. GPIO CONFIG Figure 4-15 : VistaLINK Pro – GPIO Config ® Control Panel Config: The GPIO control enables the user to configure the General Purpose Inputs and Outputs. Page 28 Revision 2.0...
4K-25G Logo Inserter WEB INTERFACE The 570DSK-25G series of products are controlled using a web interface. Login After the card has been installed and configured with the required network addresses for the control port, it can be completely configured using the web interface. For doing this, simply type the IP address of the control port of 570DSK-25G module in the web browser.
570DSK-3G 4K-25G Logo Inserter 5.1. DEVICE STATUS Figure 5-3 : WebEASY - Device Status ® Device Status: Application Status: Shows the status of the application running in the hardware. • Temperature: Shows the current temperature of the device. If the temperature is running in normal •...
Page 41
570DSK-3G 4K-25G Logo Inserter Video Config: Video Standard: Allows user to choose the video standard for DSK to pass • Lane Config: Allows user to choose Single Lane or Multi Lane • Single Lane – Ability to receive and transmit using QSFP 1.1 and QSFP 2.1 ...
570DSK-3G 4K-25G Logo Inserter 5.3. PTP CONTROL Figure 5-5 : WebEASY - PTP Status ® This section indicates the status of Precision Time Protocol (PTP), as well as the status and settings for PTP on each port connected to the 570DSK-25G. PTP Config: Domain Number: Allow the user to set the domain number of the PTP •...
Page 43
570DSK-3G 4K-25G Logo Inserter Mode: Allows the user to select the PT mode from IEEE-1588 or SMPTE2059 or AES67 • • Log Announce Interval: Allows the user to set the announce interval. Announce interval must match with the PTP settings in PTP grandmaster clock. Log Sync Rate: Allows the user to set the Sync rate.
570DSK-3G 4K-25G Logo Inserter 5.4. QSFP Figure 5-6 : WebEASY - QSFP ® QSFP sections shows the status and power levels of each QSFP lanes in each QSFP plugged in on DSK. 5.5. CONTROL INTERFACES The 1G Ethernet section shows the current status of each connection. Page 36 Revision 2.0...
570DSK-3G 4K-25G Logo Inserter Figure 5-7 : WebEASY - 1G Ethernet ® IP Address: Allows user to set and view the IP address of each control interfaces. • Netmask: Allows user to set and view the netmask of each control interfaces. •...
570DSK-3G 4K-25G Logo Inserter • MAC Address: Allows user to view This displays the MAC address for each of the 25G lanes Bandwidth Config: Allows user to config the link speed of the 25G lanes. • Link: This shows the status of each of the network ports indicating if a connection is made. •...
570DSK-3G 4K-25G Logo Inserter 5.8. VIDEO OUTPUT STREAMS The Output Streams section shows the current status and details of each Output Stream. Figure 5-10 : WebEASY - Output Streams ® Source IP: Allows user to set the source Ip address needs to be associated with multicast address. •...
570DSK-3G 4K-25G Logo Inserter Input Audio Configuration Program & Program Backup: Allows user to configure the audio ip input streams in program and • program backup section. Stream: Each stream supports 4 audio channels per multicast address. • • Source IP: Allows user to set the source ip address associated with the audio multicast address. Multicast IP: Allows user to set the multicast address for each stream •...
570DSK-3G 4K-25G Logo Inserter Multicast Port: Allows user to set the multicast port# for each stream • • Bandwidth: Allows user to view the bandwidth of the transmitting audio ip output stream. Audio RTP Payload Type: Allows user to set the audio RTP payload type. By default, keep it as 97 •...
570DSK-3G 4K-25G Logo Inserter The ANC Output Streams section shows the details of each anc output stream. Program and Preview Audio Outputs: Allow user to configure the main and backup program and • preview audio ip outputs. Source IP: Allows user to set the source ip address to be associated with the anc multicast •...
570DSK-3G 4K-25G Logo Inserter 5.14. NMOS Figure 5-16 : WebEASY - NMOS ® Control Interface: Allows user to set the NMOS control interface for controlling the 570DSK. • Discovery Mode: Allows user to set the discovery mode to discover the device in NMOS controller. •...
570DSK-3G 4K-25G Logo Inserter 5.15. GPIO CONFIG The GPIO control enables the user to configure the General Purpose Inputs and Outputs. Figure 5-17 : WebEASY - GPIO Config ® Page 44 Revision 2.0...
Open up the 570DSK’s webpage by typing out its control IP address into the browser. Login as: Username: root Password: evertz On the top of the web page there’s a button labeled “Upgrade”. The Upgrade button is used to check current firmware version and to upload the latest firmware (Figure 6-1).
570DSK-3G 4K-25G Logo Inserter Figure 6-3 : Firmware File Select Then click on the “upgrade” button. You can then watch the progress bar status: Figure 6-4 : WebEASY - Firmware Upgrade Menu ® Once completed, the device will automatically reboot. The entire process can take more than 5 minutes. Please be patient.
570DSK-3G 4K-25G Logo Inserter DEFINITIONS 4:2:2: The sampling ratio used in the HDTV digital video signal. For every 4 samples of luminance there are 2 samples each of R-Y (Red minus Luminance) and B-Y (Blue minus Luminance). 16X9: A widescreen television format such as HDTV in which the aspect ratio of the screen is 16 units wide by 9 high as opposed to the 4x3 of normal TV.
Page 56
570DSK-3G 4K-25G Logo Inserter Pixel: The smallest distinguishable and resolvable area in a video image. A single point on the screen. In digital video, a single sample of the picture. Derived from the words picture element. Serial Digital: Digital information that is transmitted in serial form. Often used informally to refer to serial digital television signals.
Need help?
Do you have a question about the 570DSK-25G Series and is the answer not in the manual?
Questions and answers