Page 1
Touchscreen Deadbolt with Alarm Model BE469 User’s Guide Please Keep This Guide You will need these c re la rm w it ’s 9 Us l BE instructions s Gui p Thi for future will d thes ions ruct Touchscreen Deadbolt with Alarm...
Toll-Free Calling From: U.S.A.: (888) 805-9837 Canada: (800) 997-4734 Mexico: 018005067866 Visit our web site for videos, FAQs and more: answers.schlage.com REGistER YoUR pRodUct Document your purchase and register your warranty at RegisterMySchlage.com, or use the included registration card. WaRRaNtY aNd Fcc/ic statEMENts...
lock sEtUp Follow these steps to get your lock set up and ready to use. If you would like to use a home automation system to enable remote control of the lock, refer to Enrolling on a Z-Wave Network on page 13. Decide what length you want the User Codes for the lock to be.
• The first button you will press when entering a User Code and in the programming process. • Press to exit programming mode immediately. Touchscreen • Remains unlit until the Outside Schlage Button is pressed. • Located on the outside of the door. • Used to enter codes for programming and unlocking. Cylinder •...
UNlockiNG L If you make a mistake while entering a User Code, press the Outside Schlage Button and then start again. Locking from the Outside 1. Press the Outside Schlage Button. 2. The lock will lock. The green check mark will light once.
Temporarily Auto-Lock must already be enabled. While the deadbolt is locked, Disable press the Outside Schlage Button and then enter a 4-8 digit User Auto-Lock Code to unlock the deadbolt. Within 5 seconds, manually lock and unlock the deadbolt using the thumbturn.
Page 7
1. Open the door and extend the deadbolt out after 30 seconds of inactivity. before beginning. 2. If you make a mistake, press the Outside Schlage Button to leave Programming Mode, and then start over. WRITE YOUR PROgRAMMINg CODE hERE FOR EASY ACCESS ENTER PROgRAMMINg MODE...
L Not sure your alarm is turned on? Simply press and release the Inside Schlage Button once. It will beep and light up to confirm it is activated. If it does not, try turning the alarm on again, and check the batteries.
Changing the Alarm Mode After you power on the alarm, it will be preset to the Forced Entry mode, by default. If you want to change the mode, follow these simple steps: L The alarm must first be powered on before changing the alert setting! Press and release the Activity button until the LEFT...
Ingersoll Rand (NYSE:IR) advances the quality of life by creating and and our family of brands—including Club Car®, Ingersoll Rand®, Schlage®, Thermo King® and Trane® —work together to enhance the quality and comfort of air in homes and buildings; transport and protect food and perishables;...
Page 11
DATE PROgRAMMINg CODE USER NAME USER CODE Example: John Smith 1234...
5. To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User Codes. See Default Codes Locations on page 6. If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving.
2. Disconnect the battery connector. 3. While watching the inside Schlage button, reconnect the battery connector. 4. The inside Schlage button will blink if the lock is enrolled. pRoGRaMMiNG UsiNG Z-WavE Many home automation systems support features of the deadbolt including locking, unlocking, and various other programming options.
1 beep Vacation Mode is enabled. Disable Green entered after Outside Vacation Mode. See Disable Vacation then Schlage button is Mode on page 7. pressed. 1 beep Too many incorrect User Codes have been 1 Red entered. Wait 30 seconds and try again.
Page 15
Deadbolt requires two — Deadbolt/frame alignment is marginal. Green attempts to lock or Adjust door/frame for best operation. unlock. Browse to answers.schlage.com for help. Alarm will not sound. — — Turn on Alarm. Alarm sounds too Alarm —...