Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet DJ Cumulus HP
Summary of Contents for Chauvet DJ Cumulus HP
- Page 1 User Manual...
- Page 2 Edition Notes The Cumulus HP User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the Cumulus HP as of the release date of this edition. Trademarks Chauvet, Chauvet DJ, the Chauvet logo, and Cumulus HP are registered trademarks or trademarks of Chauvet &...
-
Page 3: Table Of Contents
Wireless Remote Configuration ................. Settings Configuration................... Fan Speed......................No Water Warning....................Automatic Water Pump ..................Master/Slave Mode ..................5. Maintenance................Fog Machine Maintenance................Storage......................6. Technical Specifications ............Contact Us ..................Warranty & Returns..................Cumulus HP User Manual Rev. 1... -
Page 4: Before You Begin
Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. Cumulus HP User Manual Rev. 1... -
Page 5: Safety Notes
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the user. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cumulus HP User Manual Rev. 1... -
Page 6: Introduction
DMX in DMX out Power in Breaker Water inlet Water level indicator Carry handle Fluid refill cover Output nozzle Drain valve Product Dimensions 13.7 in 347 mm 18.3 in 11.9 in 464 mm 304 mm Cumulus HP User Manual Rev. 1... -
Page 7: Setup
3. Setup AC Power The Cumulus HP has a fixed voltage power supply, and it can work with an input voltage range of either 120 VAC, 60 Hz or 230 VAC, 50 Hz, depending on the specific model. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. -
Page 8: Filling The Fog Fluid Tank
Setup Filling the Fog Fluid Tank The Cumulus HP fog fluid tank must be filled with LLG (Low Lying Gallon) fluid from Chauvet DJ in order for the product to function. To access and fill the fog fluid tank: 1. Open the fluid refill cover. -
Page 9: Manual Filling
4. Return the fog fluid tank to its place and close the fluid refill cover. Do NOT overfill. While operating the Cumulus HP without the water inlet connection, make sure there is adequate distilled water in the machine to prevent pump damage. When the water level becomes low, simply add more water to continue using the Cumulus HP. -
Page 10: Installing The Hose And Floor Nozzle
The included output hose and floor nozzle allow the low-lying fog output to be directed as desired at a short distance from the Cumulus HP. To install the hose and floor nozzle: 1. Place the hose coupler over the output nozzle and turn clockwise until secure. - Page 11 4. Put the other end of the hose through the other hose clamp and over the round end of the floor nozzle. 5. Ensuring the hose clamp is over both the hose and the floor nozzle, turn the wingnut clockwise until the hose is secured to the floor nozzle. Cumulus HP User Manual Rev. 1...
-
Page 12: Operation
Auto Water Enables/disables automatic water pump from the water inlet DMX Configuration The Cumulus HP works with a DMX controller. Information about DMX is in the Chauvet DMX Primer, which is available from the Chauvet website chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf. Starting Address The Cumulus HP uses 2 DMX channels, which defines the highest recommended address to 511. -
Page 13: Standalone Configuration
3. Press <ENTER/STOP> to return to the main screen. Manual Mode To run the Cumulus HP through the display menu, follow the instructions below: 1. Press <DOWN/VOLUME> from the main screen. The display will jump to Volume Out. 2. Use <UP/TIMER> or <DOWN/VOLUME> to increase or decrease the volume, from 1–100%. -
Page 14: Settings Configuration
3. Press <ENTER/STOP> to return to the main screen. Master/Slave Mode The Master/Slave mode allows a single Cumulus HP product (the “master”) to control the actions of one or more Cumulus HP products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in either a standalone mode or with the wireless remote, while the slave products will be set to operate in slave mode. -
Page 15: Maintenance
Do Not operate the machine without fluid at any time. Fog Cleaner Quart (FCQ) was specifically developed by Chauvet to clean the Cumulus HP. Use FCQ regularly, no longer than 90 days between cleanings, to increase the life of the product. -
Page 16: Technical Specifications
Maximum External Temperature Cooling System 104 °F (40 °C) Convection I/O Connector Channel Range 3-pin XLR Ordering Product Name Item Code UPC Number Cumulus HP (120 V) 05072199 781462225476 Cumulus HP (230 V) 05072201 781462225490 Cumulus HP User Manual Rev. 1... -
Page 17: Contact Us
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. Cumulus HP User Manual Rev. 1...