Subscribe to Our Youtube Channel
Related Manuals for Dolphin BCL632FS-2
Summary of Contents for Dolphin BCL632FS-2
- Page 1 BCL632F D O L P H I N PA N E L M O U N T E D F OA M S OA P D I S P E N S E R I N S TA L L AT I O N A N D M A I N T E N A N C E G U I D E November 2019...
- Page 2 INDEX Technical Data Pre-Installation Information Pack Contents Installation Filling The Soap Tank Settings Adjustment Spare Parts List Maintenance Warranty 14-15 Troubleshooting Dolphin Blue BCL632F...
-
Page 3: Technical Data
Capacity 12V transformer Power Supply Soap viscosity Varies according to viscosity and soap consistency Standard discharge 30-100 mm +/- 10 mm Sensor range (Adjustable by remote control) Soap Type clear foaming liquid, no abrasives Soap PH 5.5-8.5 Dolphin Blue BCL632F... -
Page 4: Pre-Installation Information
Keep in mind that when using the tap installed next to the soap dispenser, the user hands should not interfere with the soap dispenser sensor detection area. Correct Installation Incorrect Installation Do not aim soap sensor at water stream Dolphin Blue BCL632F... -
Page 5: Pack Contents
PACK CONTENTS 1 x foam dispenser body 1 x foam compressor with pipe 12 v transformer 1 x quick connection fittings 1 x pump assembly with bottle support and soap tank 2 x screws 2 x anchors Dolphin Blue BCL632F... -
Page 6: Installation
Fix the base behind the wall with the hexagonal nut and the disk. 2. Fix the bottle support to the desired location. The pump MUST be within reach range of the Com cable and black supply tube. Dolphin Blue BCL632F... - Page 7 Make sure it is firmly plugged in. 5. Connect the tube extending from the foam compressor to the top of the soap dispenser pump by snapping it into the quick connection. IMPORTANT: Make sure to cut the tube to the minimum required length Dolphin Blue BCL632F...
- Page 8 PAY ATTENTION: If the 4 contacts connectors are not connected properly, the soap dispenser pump will not operate properly. 3. Plug the transformer into the electricity socket and connect the transformer connector 4. Wait about 10 seconds before placing your hands in the sensor range to avoid adjustment mode. Dolphin Blue BCL632F...
-
Page 9: Filling The Soap Tank
(if available). see page 10. Note: When the soap in the soap tank reaches the bottom line, the tank needs to be refilled. To refill the soap tank please refer to steps 1-5. Dolphin Blue BCL632F... - Page 10 Dolphin Blue BCL632F...
-
Page 11: Remote Control Functions
Once soap begins dispensing from the spout, priming is complete. press the FILL button again to stop the priming before the minute is over. Indication: continuous solid blue light in the sensor eye. Dolphin Blue BCL632F... -
Page 12: Spare Parts List
Soap Bottle 1L Support Kit ................. BC07220087 10-Pack Foam Filter ..................BC07212015 12v Transformer (EU) ..................BC06522081 12v Transformer (UK)..................BC06522086 12v Transformer (US) ..................BC06522080 12v Transformer (AU) ..................BC06522085 Remote Control for Foam Dispenser ..........BC07100009 Dolphin Blue BCL632F... -
Page 13: Maintenance
1. Use a wrench to unscrew the quick connection fitting from the foam compressor and pull out the filter housing. 2. Remove the filter from the housing. 3. Replace the filter (recommended) or wash it under running water for a temporary fix. 4. Reassemble the parts. Dolphin Blue BC632F... -
Page 14: Limited Warranty
If a defect is found in normal use, Dolphin Solutions Ltd will, at its discretion, repair, provide a replacement part or product, or make appropriate adjustments. -
Page 15: Troubleshooting
(once) when the users’ hands are within the Connectors between the electronic sensor range. Properly connect the unit and power source are electronic unit connectors to disconnected or not properly the power source connector. connected. Dolphin Blue BC632F... - Page 16 Blue light flashes The connectors between the Connect the connectors compressor (once) and the compressor and the electronic unit properly so that the white does not work motor operates. are not connected properly. o-ring is not visible. Dolphin Blue BC632F...
- Page 17 MULTIFEED DISPENSERS MANUAL 6mm BLACK TUBING ENSURE ENOUGH CLEARANCE FOR REFILLING ACCESS CUT TUBE TO 150 - 300mm 8mm CLEAR TUBING 130 x 190 Dolphin Blue BCL632 / BCL636 Series Dolphin BC632F...
- Page 18 Dolphin Solutions Ltd Southpoint, Compass Park, Bodiam, Robertsbridge, TN32 5BS Tel: +44 (0)1424 20 22 24 Fax: +44 (0)1424 205 200 info@dolphinsolutions.co.uk www.dolphinsolutions.co.uk...
Need help?
Do you have a question about the BCL632FS-2 and is the answer not in the manual?
Questions and answers