Related Manuals for Dolphin BC 632
Summary of Contents for Dolphin BC 632
- Page 1 INSTALLATION AND MAINTENANCE GUIDE BC 632 Electronic Soap Dispenser – saving soap, saving power, promoting hygiene Important: Read carefully before installing product DOLPHIN Revision February 2016...
- Page 2 INDEX Technical Data Pre-Installation Info Pack Contents Installation Filling The Soap Tank Settings Adjustment Spare Parts List Maintenance Warranty Troubleshooting Dolphin BC 632...
-
Page 3: Technical Data
TECHNICAL DATA Capacity 1 litre Power Supply 12V transformer Soap viscosity Up to 100 CPS Standard discharge Varies according to viscosity and “foamability” Sensor range 30-100 mm +/- 10 mm (Adjustable by remote control) BC 632 Dolphin... -
Page 4: Pre-Installation Information
1.50 meters between the soap dispenser and any other objects. IMPORTANT: Keep in mind that the location of the user’s hands, while using the faucet nearby should not interfere with the soap dispenser sensor detection area. Correct Installation Incorrect installation Dolphin BC 632... -
Page 5: Pack Contents
12V TRANSFORMER RANS FORMER FORMER FITTING TING 1 X PUMP ASSEMBLY WITH BOTTLE SUPPORT PUMP EMBL L Y WITH SUPPOR 1 X FOAM COMPRESSOR WITH PIPE C C O OMPRE WITH PIPE AND SOAP TANK T T A BC 632 Dolphin... -
Page 6: Installation
Insert the Soap dispenser base and the anti-rotation pin into the holes drilled. DISK HEXAGONAL NUT Fix the base behind the wall with the hexagonal nut and the disk. Fix the bottle support to the desired location. Dolphin BC 632... - Page 7 Make sure it is firmly plugged. Connect the tube coming out of the foam compressor to the top of the soap dispenser pump, by snapping it in. IMPORTANT: Make sure to cut the tube to the required length BC 632 Dolphin...
- Page 8 Plug the transformer into the electricity socket and connect the FROM THE TRANSFORMER RANS FORMER TO THE SOAP DISPENSER PENS PENS transformer connector Wait about 10 seconds before you ABOUT ABOUT place your hands within the sensor range. SECONDS Dolphin BC 632...
-
Page 9: Filling The Soap Tank
This operation can also be done using the soap dispenser remote control Refill function. NOTE: Once the soap in the soap tank has reached the bottom line the soap tank should be refilled. To refill the soap tank please refer to steps 1-5. BC 632 Dolphin... -
Page 10: Settings Adjustments
To stop this activity press the FILL button again. If the soap has not started coming out of the spout, press the FILL button again. Indication: continuous blinking of the blue light in the sensor eye. Dolphin BC 632... - Page 11 SPARE PARTS LIST Seals and Screws Kit BC 07210098 Sensor Kit 10-pack BC 07220338 FD Components Kit BC 07222019 Bottle 1L support BC 07120175 Soap Tank 1L BC 07100020 Filter 10-Pack BC 07212015 12V Switching transformer BC 06522081 BC 632 Dolphin...
-
Page 12: Maintenance
If the soap supply has decreased, this can be because the filter is clogged. The filter can be cleaned as following: 1. Unscrew the nut at the top of the foam compressor and pull out the filter. 2. Wash the filter under running water. 3. Reassemble the parts. Dolphin BC 632... -
Page 13: Warranty
If a defect is found in normal use, Dolphin will, at its discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty. -
Page 14: Troubleshooting
Increase the air ratio using the remote control. Foam is too diluted Air ratio is too low Refer to page 8. Dolphin BC 632... - Page 15 Soap coming out of the spout does not stop The connectors between the Connect the connectors compressor and the electronic unit are properly so that the white o-ring not connected properly. is not visible. BC 632 Dolphin...
- Page 16 DOLPHIN Request your 320 page catalogue today on 0800 0723 404 Bell-Chem Products Company Haywood Way, Hastings TN35 4PL Tel: +44 (0)1424 202224 Fax: +44 (0)1424 205 200 info@dolphindispensers.co.uk www.dolphindispensers.co.uk Dolphin BC 633F...
Need help?
Do you have a question about the BC 632 and is the answer not in the manual?
Questions and answers