Advertisement
BASIC OPERATIONS
RECEPTION USING PRESET TUNING
1. Perform the preliminary operations on page 12.
2. Press the STATION CALL switch into which the desired
station has been memorized.
® To listen to a Mode 1 broadcast, press the switch once,
and to listen to a Mode 2 broadcast, press it twice.
In this way, simple and accurate reception of any desired
station is possible.
NOTE:
°
The
contents
of the
STATION
CALL
switches
will be
preserved for several days, even if the power cord is un-
plugged.
©
/f a preset station has been erased, re-preset it.
Last Station Memory
*
When the POWER switch is pressed to turn power on, the
last station received
before
the power
was
previously
turned STANDBY mode will be received again.
e
When power is ON, if the BAND selector switch is pressed,
the last station received before the BAND selector switch
was previously pressed will be received again.
TAPE PLAYBACK
Single Playback (a function of both Decks | and Il)
1. Perform the preliminary operations on page 12.
2. Press the STOP/EJECT switch and load a pre-recorded cas-
sette tape then close the cassette door.
3. Select the DOLBY NR switch.
4. Press the PLAY (>) switch.
@ Press the PLAY ( >>) switch of the deck into which the
cassette tape is loaded.
5. Adjust the volume with the VOLUME control and the tone
with the GRAPHIC EQUALIZER controls.
6. To stop playback, press the STOP/EJECT switch.
Relay playback (Continuous playback Deck | >
Deck Il, or Deck i > Deck I)
© A deck will enter the standby mode if its PLAY switch is
pressed while the other deck is in the play mode.
When the deck presently playing is stopped, the deck in
the standby mode will automatically enter the play mode
for relay play.
«
While the second
tape is playing, a new
tape can be
replaced in the first deck in order to perform continuous
playback of different tapes. This is a convenient feature for
party background music, etc.
. Perform the preliminary operations on page 12.
2, Load pre-recorded cassette tapes into both Deck | and
DECK Il. (Press the STOP/EJECT
switch and load the
cassettes.) Close the cassette doors.
3. Select the DOLBY NR switch.
4. Press the PLAY (>) switch for the deck you wish to be-
gin playing first, then press the PLAY { [>) switch for the
other deck.
e When the tape which is playing back reaches the end
and automatically stops, the other deck automatically
starts playback.
14
<ARB1057>
5. Adjust the volume with the VOLUME contro! and the tone
with the GRAPHIC EQUALIZER controls.
6. To stop playback, press the STOP/EJECT switches.
NOTES:
¢
Pressing Pause from the remote control during relay playback,
stops the playback from one deck and starts playback from
the other deck.
=
¢
Starting playback from one deck after pressing Pause from
the remote control while one deck is playing back, cancels the
pause and starts playback from the previous deck in the re-
lay playback mode.
TAPE RECORDING {A Function of Deck il Only)
PLAY switch
DOLBY NR switch
REC switch
STOP/EJECT switch
1. Perform the preliminary operations on page 12.
© Select the recording source with the FUNCTION switch,
2. Press the STOP/EJECT switch and load the cassette tape
to be used for recording into Deck il. Close the cassette
door.
3. Select the DOLBY NR switch.
4, Starts playback of the source being recorded.
® When recording the sound from Deck | on Deck II (tape
dubbing), start playback of Deck | after loading the cas-
sette tape.
5. Hold down the REC (@) switch first and then press the
PLAY
(>) switch.
e The REC indicator will light.
® Tape recording
is unaffected
by the VOLUME
and
GRAPHIC EQUALIZER setting.
NOTE:
*®
Beat may occur and be included in recordings when record-
ing AM broadcasts. in such cases, set the BEAT
CUT switch
on the rear panel to the side where beat is less.
*
Use remote contro! pause only for Deck Hf during tape dub-
bing. The Deck If pause will not be released even if Deck fis
|
played back in this status.
6. To stop recording, press the STOP/EJECT switch.
Erasing the tape {function of Deck II only)
When recording on a previously recorded tape, the previous-
ly recorded sounds will be erased and new recording entered
on the tape. To erase a previously recorded tape without
recording anew, perform the following operations.
Advertisement
