Relay Recording; Parallel Recording - Pioneer CT-W830R Operating Instructions Manual

RECORDING
RELAY RECORDING
@ Recording Using Both Decks in Sequence
=
. Insert cassette tapes for recording into both decks.
2. Set each type of the DOLBY NR switch on each deck @ or
@.
* The type of the DOLBY NR system can be set separately for
DECKs | and Il.
. Set the REVERSE MODE switch © (see page 11).
. Set the recording source on the amplifier.
. Set the tape transportation direction for recording (see page
10).
Set the separate direction for DECKs | and Il.
. Press the recording button (@) on DECK I.
. Adjust the recording level (see page 14).
. Press the RELAY/SKIP button @.
The [RELAY/SKIP] indicator lights.
9. Press the pause button (1) on DECK I.
Relay recording starts from DECKs | to Il.
at w
OND
B® Recording Pause
Press the pause button (fl) on the deck in operation.
Press the button again to resume recording.
@ Recording Completion
Press the stop button (lM) on the deck in operation.
@ Relay Recording Release
Press the RELAY/SKIP button @ again.
(The indicator turns off.)
Press the button once to release relay recording. To resume
relay recording, replace the recorded tape with a new tape, then
press the RELAY/SKIP button @ again.
(The indicator lights.)
Different Operations Depending on the Combinations of the
Tape Transportation Directions and Reverse Modes
Tape transportation
mode atthe Start of
recording
Reverse mode
ake. a) Ca}
One-way mode
DECK i | DECK II
Two-way mode or repeat mode
F: Forward recording (recording the front side of a cassette tape)
R: Reverse recording (recording the back side of a cassette tape)
—: Relay operation
NOTES:
@ When erasure prevention tabs are broken, you cannot record
even if you press the recording button (@).
® Always set TIMER switch © to OFF.
You cannot relay-record from DECKs I to I.
@ When a tape reaches the end, DECK | automatically stops
recording. then DECK Il starts recording. It automatically stops
recording when the tape reaches the end.
PARALLEL RECORDING
@ Recording Using Both Decks Simultaneously
1. Insert cassette tapes into both decks for recording.
2. Set the type of the DOLBY NR switch on DECK | (9.
* You cannot set different types of the DOLBY NR system for
DECKs | and Il.
(The type of the DOLBY NR system for DECK | is applied to
DECK Il. Therefore, the setting for DECK Il is ignored and the
indicator for it is the same as the one set for DECK I.)
. Set the REVERSE MODE switch © (see page 11).
. Set the sound source on the amplifier for recording.
. Set the tape transportation direction for recording (see page
10).
Set separate directions for DECKs | and Il.
. Press the recording button (@) on DECK J.
. Adjust the recording level (see page 14).
. Press the stop button (M@) on DECK I.
. Press PARALLEL REC button @.
Both DECKs | and II start recording the same sound source.
on WwW
COON
@ Parallel Recording Pause
Press the pause button (fll) on either deck (both decks pause).
@ Parallel Recording Completion
Press the stop button (Ml) on either deck (both decks pause).
NOTES:
@ When either tape reaches the end, parallel recording
completes. Therefore, use the same length tapes for both decks.
@ /f the erasure prevention tabs are broken, you cannot parallel-
record even if you press PARALLEL REC button @®.
@ Always start recording from the forward direction (FWD) for
repeat recording. Otherwise, the tape automatically stops when
it reaches the end in the reverse direction.
®@ Since the recording level adjustment effects both decksequally,
it is recommended to use the same type of cassette tapes.
e@ /fyou press the recording mute button (Q), both decks errter the
recording mute mode (see page 14).
15
<RRI$064>