Tape Copying; Timer Recording - Pioneer CT-W830R Operating Instructions Manual

TAPE COPYING
fWNhH— 6
Copying the recorded tape from DECKs I to Il
. Insert a recorded cassette tape into DECK | for playback.
. Insert a blank cassette tape into DECK II for recording.
. Set the REVERSE MODE switch © (see page 11).
. Set the tape transportation direction (see page 11).
* For repeat copying, always set the direction to forward (FWD).
If set to reverse (REV), the tape automatically stops when it
reaches the end.
. Press the SYNCHRO COPY button @.
® Using the [NORMAL SPEED] button (normal speed copying)
Copying while listening to music
® Using the [HIGH SPEED] button (double speed copying)
Copying the whole tape quickly
NOTE:
The tape in DECK I! will be copied in the same type of the DOLBY
NR switch @ as DECK I's tape, irrelevant to its own setting. When
listening to the copied tape, set the type of the DOLBY NR switch
on DECK |.
Releasing Copying
Press the stop button (MM) on either deck (both decks enter the
stop mode).
NOTES:
There are 2 kinds of tape copying: one is normal speed copying
while listening to recording music; the other is double speed
copying that takes only half the normal speed copying.
The recording level adjustment is not necessary during tape
copying.
No other button except the stop button (@) is disabled during
double speed copying.
The recording mute button (Q) and pause button (MW) on DECK Il
are operable during normal speed copying.
When either tape reaches the end, the tape copying made is
released. Therefore, use the same length tapes for both decks.
When copying the same recorded tape multiple times, always
use the original tape as a recording source. Copying a copied
tape deteriorates the sound quality.
During double speed copying, noise (beep sound) may be
recorded if a TV is placed nearby. In this case, either switch the
double speed copying to normal speed copying or turn off the
TV.
TIMER PLAYBACK/RECORDING
1. Insert a recorded cassette tape for playback.
Playback is operated on the deck where the tape is loaded.
If both decks are loaded with cassette tapes, relay playback is
operated.
2. Set the type of the DOLBY NR switch @ and/or @.
3. Set the REVERSE MODE switch © (see page 11).
4. Set the stereo amplifier to tape playback (tape monitor).
Set the sound volume for the timer for playback (listen to the
sound once to check the volume).
5. Set the tape transportation direction (see page 11).
6. Set the audio equipment timer.
After setting, all equipment are turned to off.
7. Set TIMER switch @ to PLAY.
When the specified time on the audio timer comes, all
equipment are turned on to automatically start playback.
NOTES:
@ During timer playback, blank skip functions to fast-forward the
tape to the next track for playback when an unrecorded section
continues for about 15 sec.
@ Always set the same type of the DOLBY NR system as
recording.
® Refer to the timer instruction manual for details, since every
audio timer requires a different procedure.
e
Always set the timer switch to off when the timer is not used.
/f set to play, playback automatically starts when the deck is
turned on.
/
TIMER RECORDING (unattended recording)
1.
aa w
Insert a cassette tape for recording.
The deck where the tape is loaded records. When both decks
are loaded with tapes, relay recording starts.
. Set the type of the DOLBY NR switch @ and/or @.
You can separately set the type of the DOLBY NR system for
DECKs | and li.
. Set the REVERSE MODE switch @ (see page 11).
. Set the tape transportation direction (see page 11).
. Set the recording source on the amplifier.
Set the input switch to tuner on the amplifier, then select the
desired broadcast.
. Press the recording button (@).
The deck enters the recording pause mode.
. Adjust the recording level (see page 14).
. Set the audio equipment timer.
After setting, all equipment are turned off.
. Set TIMER switch @ to REC. |
When the specified time on the audio timer comes, all
equipment are turned on to start recording.
NOTES:
Note than even if you leave a cassette tape in DECK If
unintentionally, relay recording automatically starts from DECK
1 then moves on to DECK It.
Set the tape transportation directions for both decks to operate
relay recording.
If the erasure prevention tabs are broken, timer record/ng is
disabled.
Refer to the timer instruction manual for details, since each
audio timer requires a different procedure.
Always set the timer switch to off. If set to rec, recording
automatically starts when the deck is turned on.
17
<RRBIO64>