Table of Contents
Advertisement
Available languages
Available languages
Instructions for Use
5
Press
and select drying
• When you want to adjust the drying function included in the previous program, you can do so by pressing the
Dry button. Each time you press, you can switch the drying mode according to the chart below.
The display indicators will light on in turn.
Basic, Intense program
Eco program
Factory
0.5 h
Keep
+
setting
1 h
1 h
+
Keep
No Drying
Air
Air
+
Keep
No Drying
0.5 h
Reminder
● After adjusting the drying mode, the overall operating time will also change.
● When No Drying is selected, air blowing will continue for about 3 minutes (about 30 minutes if dishwasher salt is
added), which is normal. (This is to discharge some of the hot air to avoid burns.)
6
Press
to start
• Drying starts according to the selected program,
and ends with 6 beep sounds.
• If you do not press this button after the above steps,
power will be automatically turned off after 10 minutes.
■ Delay Start program
You can preset to start the operation 4 hours later by the following procedure.
After step 5 in pages EN9 - EN11,
Press
, the indicator for
press
(operation will start 4 hours later)
Reminder
● You cannot use the Delay Start function in Dry Only, Speedy, Speedy + 80°C programs.
● If you want to cancel Delay Start, press
EN11
Speedy, Care program
Dry Only program
Air
No Drying
Air
Keep
0.5 h
+
0.5 h
+
Keep
0.5 h
1 h
0.5 h
+
Keep
1 h
+
Keep
1 h
Air
1 h
Keep
Air
Keep
+
+
Caution
● Take out the items after 30 minutes from the end
of operation (to avoid burns).
● Clean the filter after each operation. (page EN13)
in the display will light up,
, the indicator "4 hours" will light off.
Drying • Delay Start • Change the Settings
■ Change the Settings
Various settings can be changed according to your preference or actual situation.
Enhanced washing settings
Confirm power is turned off
Press Delay Start and Start/Pause for
1
2.5 seconds simultaneously.
1 h
Start setting after 2 beep sounds.
Press Delay Start, and select function
0.5 h
2
code "1 h".
Press Program again and select the
3
option code as needed (whether to
enhance washing).
Press Start/Pause to save the setting
4
and 6 beep sounds complete the setting.
Enhanced drying settings
Confirm power is turned off
Press Delay Start and Start/Pause for
1
2.5 seconds simultaneously.
Start setting after 2 beep sounds.
Press Delay Start and select the function
2
code "1 h + Air".
Press Program again and select the
3
option code as needed
(whether to enhance drying).
Press Start/Pause to save the setting
4
and 6 beep sounds complete the setting.
Disable the buzzer setting after operation
Confirm power is turned off
Press Delay Start and Start/Pause for
1
2.5 seconds simultaneously.
Start setting after 2 beep sounds.
Press Delay Start and select the function
2
code "0.5 h".
Press Program again and select
3
the option code as needed (whether
to disable the buzzer for operation
completion).
Press Start/Pause to save the setting
4
and 6 beep sounds complete the setting.
If you want to enhance the washing performance by extending the washing
time, change the settings as follows.
Function
Option code
code
(whether to
(press Delay
enhance washing)
Start)
(press Program)
0
No need
1 h
1
Enhanced
If you want to enhance the drying performance by extending the drying time,
change the settings as follows.
Function
Option code
code
(whether to
(press Delay
enhance drying)
Start)
(press Program)
0
No need
1 h + Air
1
Enhanced
If you want to disable the buzzer at the completion of the
dishwashing, make the changes as follows.
Option code
(whether to
Function
enable or disable
code
the buzzer
(press Delay
for operation
Start)
completion)
(press Program)
0
Disable
0.5 h
1
Enable
* Indicates that the operation mode is factory set.
Display indicator
(lights up)
1 h *
1 h + Intense
Display indicator
(lights up)
1 h + Air *
1 h + Air + Intense
Display indicator
(lights up)
0.5 h
0.5 h + Intense *
EN12
Advertisement
Table of Contents
