Panasonic NP-TH1WEVN Operating Instructions Manual page 11

Error Indication
Freezing prevention
In the event of freezing occurs and the problem is ignored, it may cause damage to the supply
valve and piping. For draining treatment and freezing prevention, please contact Service Centre.
Panasonic staff handling the draining should note the following:
■ If the relevant parts or pipes were already frozen, please do the following
❶ Select Speedy to run 1 - 2 times to defrost. (If the situation is serious, repeat the operation several times)
❷ After the process is completed, wait for 30 minutes, remove the supply hose from the dishwasher, and
drain out the water from the hose.
❸ Take off the rubber cover (black) at the front, shake the dishwasher on all sides, and drain out all the
water inside.
❹ Put the rubber cover back in place.
EN17
(cont.)
Not in use for a long time
Troubleshooting
■ Check the following first. If the problem still continues or there are other symptoms, please contact
Service Centre.
Symptoms
The appliance does not
● Is the door closed firmly? → Close the door firmly and restart the operation.
work
● Have you used kitchen detergents? Or is kitchen detergent not rinsed off completely
from the items in the pre-wash? → You must use dishwasher detergent.
Water is supplied and
(Kitchen detergent may generate excessive foam. Supplying and draining water
drained repeatedly
repeatedly is necessary to eliminate the foam. The operation time will be prolonged.
Do not open the door during the process to avoid water leakage.)
Dew condensation ● Dew condensation may occur due to the temperature difference between the
around the door dishwasher body and the kitchen, which is not a malfunction.
Steam comes out from
around the door during
● Steam or warm air may come out, but this is not a malfunction.
operation
After using for a while,
the inside walls of the
● This is caused by the minerals contained in the water.
dishwasher become
whitish
Water is left under the
● Water may be left at the bottom. This is not a malfunction.
filter
Water supply does not ● The water supply valve may be broken. Close the water supply valve or the water tap
stop valve (but leave the power plug connected), and contact Service Centre.
● For a while after it is purchased, the rubber and resin components of the dishwasher
Odour emits during
may emit some odour, which have no adverse effect on the human body and will
operation
disappear after a period of time.
● A foul odour may be generated as a result of the deterioration of water remained in the
Smell like a sewer
appliance if it is left unused for a long time. → Select and run the Care program.
● This is due to residue such as fish skin left on the filter.
Fishy smell → Remove and clean it using a brush (page EN13). If the smell persists, select and
run the Care program.
When the nozzles start
● This is the sound of the nozzles switching sequentially before spraying, which is not a
spraying, they make a
malfunction.
clattering sound
● Depending on the types of tableware and how they are loaded, the noises may get
louder during operation.
Noises change during ● Are the filters clogged? (When the filters are clogged, the sound of the pump may
operation suddenly become loud during operation.) → Clean the filters (page EN13)
● During operation, the electronic components will make chattering sounds when they
are switched. This is not a malfunction.
● ① Select and run the Speedy program 1 - 2 times (to defrost).
② Check whether you can run the Speedy program.
Freezing
• If the freezing is the result of being left unused for a long period of time, defrost may
not work even after running the Speedy program 1 - 2 times.
→ Contact Service Centre (page EN17)
● Is the dishwasher (location, drain hose, supply hose) installed correctly?
Water leakage
→ Check carefully (page EN24)
● Turn off the power to stop the operation. When water supply resumes, discharge the
Water supply stops
muddy water from another tap, and then restart the operation.
● When electricity supply resumes, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running at the
Power cut time of the power cut.
• If delay start was selected and was waiting to start later, the selected program with
delay start will be cancelled.
● Check the causes, reset the circuit breaker, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running at the
Circuit breaker has
time of the power cut.
tripped
• If delay start was selected and was waiting to start later, the selected program with
delay start will be cancelled.
"Salt" stays lighted up
● The display indicator "Salt" will light up if the dishwasher salt is not adequate.
in the display (page EN9)
Causes and Solutions
EN18