Download
Share
Print this page
Panasonic NP-B6M1FIGB Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Dishwasher
  5. NP-B6M1FIGB
  6. Service manual
Panasonic NP-B6M1FIGB Service Manual

Panasonic NP-B6M1FIGB Service Manual

Hide thumbs

Advertisement

Quick Links

TABLE OF CONTENTS

1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Operating Instructions------------------------------------------ 4
4 Test Mode ----------------------------------------------------------12
6 Wiring Connection Diagram ---------------------------------45
Model No.
Model No.
Destination UK
PAGE
© Panasonic Corporation 2013 Unauthorized copy-
ing and distribution is a violation of law.
Order No.
Dishwasher
NP-B6M1FIGB
NP-B6V1FIGB
PAGE

Advertisement

loading

Related Manuals for Panasonic NP-B6M1FIGB

Summary of Contents for Panasonic NP-B6M1FIGB

  • Page 1: Table Of Contents

    3 Operating Instructions------------------------------------------ 4 4 Test Mode ----------------------------------------------------------12 5 Disassembly and Assembly Instructions ---------------15 6 Wiring Connection Diagram ---------------------------------45 7 Exploded View and Replacement Parts List -----------46 © Panasonic Corporation 2013 Unauthorized copy- ing and distribution is a violation of law.

  • Page 2: Safety Precautions

    1 Safety Precautions 1.1. Health & Safety Note: When servicing the SCHOLTES oven, health and safety issues must be considered at all times. Specific safety issues are listed below with their appropriate icon. These are illustrated throughout the service information to remind service people of the health and safety issues 1.1.1.

  • Page 3: Specifications

    2 Specifications...

  • Page 4: Operating Instructions

    3 Operating Instructions...

  • Page 12: Test Mode

    4 Test Mode 4.1. Test mode 4.1.1. Test mode activation Activation mode The test mode activation can be done if the dishwasher is at the beginning status with empty chamber. To do this it is enough to recall the “program cancellation” mode described at point 2.2. The test mode is then recalled as following described: 1.
  • Page 13 4.2. Test mode list Phase Description Alternate valve postion Warning lights TEST MODE BEGINNING: The door should be closed when the test mode operates. TEST MODE BEGINNING Upper spray arm Close the door. After some seconds the machine (upper washing, if it is starts to fill the water.

  • Page 14: Error Code

    4.3. Error code Error code The possible errors and the relative LED displays are shown below. If an error is detected during the test mode, correct the error and then open and close the door to continue with the test. ERROR CODE Malfunction What the display shows...

  • Page 15: Disassembly And Assembly Instructions

    5 Disassembly and Assembly Instructions Component dismantling 1. As a safety precaution, always disconnect hydraulic and electrical connections before servicing. Failure to observe these safety rules may result in damage to people and/or property. 2. To avoid the danger of electrical surges you must disconnect the appliances from the mains by pulling out the plug or depress- ing the corresponding magnetothermic switch on the electrical service panel.
  • Page 16 2. Remove the two front screws (right and left). 3. Remove it from the auction of movement. 4. Disconnect the power connector. 5.3. Dismantling automatic door opening movement 1. Remove the top cover. 5. Remove the faston from the micro. 2.
  • Page 17 5.4. Dismantling the hook of the 6. Lift and remove the micro from the bracket. doorlock 1. Remove the fixing screw. 7. From the inside, remove the three screws that. 2. Leverage with a screwdriver at the base of the lock. 8.
  • Page 18 4. Remove the hook. 3. Leverage delicately where indicated. 4. Then remove the lights. 5.5. Dismantling the lighting LED 1. With a screwdriver lift ..5. Remove the plastic lens. 2. The protective cover.
  • Page 19 5.6. Dismantling the Doorlock 5.7. Dismantling the basket guides 1. Disconnect the electrical connection. 1. Remove the screws on the side of the dishwasher. 2. Remove the 2 screws. 2. 2 screws for the cutlery basket. 3. The procedure is the same for all guides baskets. 3.
  • Page 20 4. 4 screws for the upper rack. 3..lift the plastic filter. 4. Extract the stainless steel filter. 5.8. Dismantling the internal feed tube of the spray arms 1. Remove the spray arms. 5. Remove the screw which locks the tube. 2.
  • Page 21 6. Remove the hose sprayer from the sump. 8. Remove the pipe joints from 2 sides. 7. And from the pipe (inserted interlocking). 9. Remove the pipe. 10..from 2 sides.
  • Page 22 11..remove the hose sprayer. 2. With the help of tool n 6, rotate the locking ring anticlock- wise for one revolution. 3. Remove the press/switch gasket and 12. Remove the rotating sprayer. 5.9. Dismantling the air break 1. Remove the [toothed] airbreak locking ring located inside the dishwasher, on the right hand side as seen from the front.
  • Page 23 4. Disconnect the connection to the sump 7. remove the airbreak from the ..8..water softener unit 5. remove the wiring connector 6. is now possible to remove the ring nut washer.
  • Page 24 5.10. Dismantling spring and hinges 1. Move the cord away from the friction device. 3. Pass the spring tensioning cord through the friction device. 2. Release the spring tensioning cord from the compensa- tor. 4. Release the spring from the other end of the cord.
  • Page 25 5. Remove the cord from the spring. 8. Remove the spring. 6. Remove the screw of the bracket/spring. 9. Remove the 2 screws fixing the hinge to the door. 7. Remove the spring/bracket. 10. Remove the 2 screws holding the hinge to the side.
  • Page 26 11. Turn the hinge down, remove it. 2. Now remove the front panel from its housing to access the internal components. 5.11. Dismantling the front panel, timer and light cycle end/ microswitch 1. Open the door and remove the 6 front panel torx fixing screws.
  • Page 27 5. Disconnect the electrical connecting wires of the dis- 8. Remove the microswitch screws. penser. 6. Disconnect the electrical connecting wires of light cycle 7. and its microswitch.
  • Page 28 9. We now have easy access to the components of the front panel. 10. to replace the timer follow these steps. 12. To completely remove the component from its housing, disconnect the relative electrical connecting wires. 11. with a screwdriver to lever as in picture. 13.
  • Page 29 14. Disconnect the electrical connecting wires. 17. Disconnect the electrical connecting wires. 15. Disconnect the electrical connecting wires. 18. with a screwdriver to lever as in picture. 16. Disconnect the electrical connecting wires. 19. Disconnect the electrical connecting wires.
  • Page 30 5.12. Dismantling the detergent dis- 4. Remove the 6 detergent dispenser fixing screws (tool n1) and disconnect the electrical rast connector. penser 1. Remove the inner door liner fixing screws (tool n 5) to access the detergent dispenser. 5.13. Dismantling the gasket (tank) 1.
  • Page 31 3. Remove the seal, pull slightly forward. 3. Where indicated. 4. Remove the screw system acquatop. 5.14. Dismantling the botton tray 1. The botton tray is fixed of 6 position. 5. Remove the botton tray. 2. Leverage with a screwdriver.
  • Page 32 5.15. Dismantling the plint 5.16. Dismantling pressure switch 1. The plint is fixed at 2 points. 1. The pressure switch is fixed on the water softener inter- locking. 2. Leverage with the screwdriver. 2. Remove the electrical connector. 3. Remove protection. 3.
  • Page 33 5.17. Dismantling the drain pump 5.18. Dismantling acquastop system 1. Rotate the pump clockwise. 1. Remove the float, by levering. 2. Remove it from the sump. 2. As indicated in the picture. 3. Disconnect the connector.
  • Page 34 5.19. Dismantling the probe NTC 3. Remove the microswitch. 1. With a screwdriver. 4. Disconnect the microswitch. 2. Disconnect the probe NTC. 3. To remove the probe.
  • Page 35 5.20. Dismantling the valve Alternate 4. Turn it counterclockwise. washing 1. Using a screwdriver. 2. Release the hose. 3. Remove the two screws.
  • Page 36 4. Fixing the valve. 7. Remove the valve. 8. Disconnect with a screwdriver. 5. Using a screwdriver, leverage in. 9. The wiring connection. 6. The points indicated.
  • Page 37 5.21. Dismantling the sump 4. Use a screwdriver to remove the clamp. 1. Remove the screws holding the sump to the tank. 5. Remove the hose. 2. Remove all hoses connected. 6. Remove the sump. 3. Remove all hoses connected.
  • Page 38 5.22. Dismantling the heating ele- 4. to the wiring. ment 1. Use a screwdriver. 5.23. Dismantling the wash pump 1. Disconnect the electrical connections. 2. To remove the clamp. 2. to the wiring. 3. Removing connections.
  • Page 39 5.24. Dismantling the power cable 3. Remove the rubber motor mounting. 1. The support of the power cable is attached, interlocking. 4. To completely free the motor from its position. 2. To go out from the rear the support.
  • Page 40 5.25. Dismantling the water softener 3. Removing connections. and acquastop tube 1. Remove the salt cap. 4. to the wiring. 2. Remove the [toothed] locking ring nut located inside the 5. Remove the cable from the mount. 3. Dishwasher immediately under the cap by rotating it anti- clockwise.
  • Page 41 4. Once all the electric wires. 7. Remove the protective metallic. 5. and connecting pipe. 8. Operate with a gripper on the mounting tabs. 9. Remove the water softener. 6. To the water softner.
  • Page 42 10. Now you can remove the hose acquastop. 2. Remove the inferior gasket. 11. From the water softener. 5.27. Dismantling the front lower plastic crossbar 1. The cross is fixed to the dishwasher at the sides with 4 screws. 5.26. Dismantling the gasket tank bottom 1.
  • Page 43 3. Use a screwdriver to lever under the gasket. 2. Disconnect the relative electrical connecting wires. 4. Remove the front lower plastic crossbar. 3. The relay board is lock fixed. 5.28. Dismantling relay and trans- former lights 1. Is positioned inside the base.
  • Page 44 4. The transformer is fixed with screws.

  • Page 45: Wiring Connection Diagram

    6 Wiring Connection Diagram...

  • Page 46: Exploded View And Replacement Parts List

    7 Exploded View and Replacement Parts List 7.1. NP-B6M1FIGB 7.1.1. Exploded View_A...
  • Page 47 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 61096 759130488 GASKET 4 POSITIONS H860 　 　 61261 761810230 DUCT SECTOR UPPER B.860 G 　 　 66036 761810267 DUCT FOR BASKET 　 　 81326 690370525 GR.SUMP LS08 ALTER. 　...
  • Page 48 7.1.2. Exploded View_B...
  • Page 49 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 3154 696291902 TIMER 067FW050MD223PA026 　 　 67541 697690215 LOCK GROUP ITW MAX 1MIC 　 　 70893 820732534 FLAT CABLE 　 　 81409 692050898 INNER DOOR ASS.LS08 　 　 82765 768413949 ELECTR.MODULE SUPPORT ST 　...
  • Page 50 7.1.3. Exploded View_C...
  • Page 51 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 692650086 WAT.SOFT.LS6012REEDHST 　 　 766610243 AIR BREAK LS 2012DECFLO 　 　 758974506 DRAIN HOSE/SIPHON LS60 　 　 758974507 AQUASTOP HOSE 2012 　 　 36457 754130914 JOINT ANNEAU 　 　 40228 754130980 RING GASKET...
  • Page 52 7.1.4. Exploded View_D...
  • Page 53 96344 694170619 FRICT.HIG.HINGE PIN DX 96345 694170620 FRICT.HIG.HINGE PIN SX 97958 938820027 CORD FOR HINGES FV820 AFC 98990 696291822 RELAY BOARD X2 PANASONIC 98992 810072509 AC 230V LEDLIGHT 98998 820733631 CONNECTIONS ALIM LED1 P 99002 693331940 SIDE RIGHT SIDE LEFT...
  • Page 54 7.1.5. Exploded View_E...
  • Page 55 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 23623 814490201 MICROSWITCH 　 　 87469 768414122 NO CRUSHING DX AFC 　 　 87470 768414123 NOCRUSHING SX AFC 　 　 87472 768936356 CROSSES MOBILE AFC 　 　 87474 768170057 PUSHER DOOR AFC 　...
  • Page 56 7.1.6. Exploded View_F...
  • Page 57 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 61262 698290726 BASKET ADJUST.860STD GR.R 　 　 61263 698290727 BASKET ADJUST.860STD GR.L 　 　 75847 697410197 GR.UPPER BASKET WHEEL G. 　 　 76170 767410200 LOWER BASKET WHEEL GREY 　 　...
  • Page 58 7.2. NP-B6V1FIGB 7.2.1. Exploded View_A...
  • Page 59 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 61096 759130488 GASKET 4 POSITIONS H860 　 　 61261 761810230 DUCT SECTOR UPPER B.860 G 　 　 66036 761810267 DUCT FOR BASKET 　 　 81326 690370525 GR.SUMP LS08 ALTER. 　...
  • Page 60 7.2.2. Exploded View_B...
  • Page 61 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 3211 696291903 TIMER 　 　 67541 697690215 LOCK GROUP ITW MAX 1MIC 　 　 70893 820732534 FLAT CABLE 　 　 81409 692050898 INNER DOOR ASS.LS08 　 　 82765 768413949 ELECTR.MODULE SUPPORT ST 　...
  • Page 62 7.2.3. Exploded View_C...
  • Page 63 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 692650086 WAT.SOFT.LS6012REEDHST 　 　 766610243 AIR BREAK LS 2012DECFLO 　 　 758974506 DRAIN HOSE SIPHON LS60 　 　 758974507 AQUASTOP HOSE 2012 　 　 36457 754130914 JOINT ANNEAU 　 　...
  • Page 64 7.2.4. Exploded View_D...
  • Page 65 694170619 FRICT.HIG.HINGE PIN DX 96345 694170620 FRICT.HIG.HINGE PIN SX 97958 938820027 CORD FOR HINGES FV820 AFC 98990 696291822 RELAY BOARD X2 PANASONIC 98992 810072509 AC 230V LED-LIGHT 98998 820733631 CONNECTIONS ALIM - LED1 P 99002 693331940 SIDE RIGHT SIDE LEFT...
  • Page 66 7.2.5. Exploded View_E...
  • Page 67 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 23623 814490201 MICROSWITCH 　 　 87469 768414122 NO CRUSHING DX AFC 　 　 87470 768414123 NOCRUSHING SX AFC 　 　 87472 768936356 CROSSES MOBILE AFC 　 　 87474 768170057 PUSHER DOOR AFC 　...
  • Page 68 7.2.6. Exploded View_F...
  • Page 69 Safety Ref.No. Part No. Part Name & Description Remarks 　 　 61262 698290726 BASKET ADJUST.860STD GR.R 　 　 61263 698290727 BASKET ADJUST.860STD GR.L 　 　 75847 697410197 GR.UPPER BASKET WHEEL G. 　 　 76170 767410200 LOWER BASKET WHEEL GREY 　 　...

This manual is also suitable for:

Np-b6v1figb