Using The Unit Safely - Roland DJ-2000 Owner's Manual

Professional dj mixer
Hide thumbs Also See for DJ-2000:
Table of Contents

Advertisement

USING THE UNIT SAFELY
INSTRUCTIONS FOR THE PREVENTION OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
About A\ WARNING and Z\. CAUTION Notices
Used for instructions intended
to alert
the user to the risk of death or severe
Z\WARNING
injury
should
the
unit
be
used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage
should
the
unit
be
used
improperly.
Z\ CAUTION
* Material damage refers to damage or
other
adverse
effects
caused
with
respect
to
the
home
and
all its
furnishings,
as
well
to
domestic
animals or pets.
Z\WARNING
¢ Before using this unit, make
sure to read the \\
instructions below, and the Owner's Manual.
* Do not open or perform any internal oe)
on the unit. (The only exception would be where this
manual provides specific instructions which should
be followed in order to put in place user-installable
options; see p. 20.)
* Make sure you always have the unit placed so it c@
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
* Avoid damaging the power cord. Do not bend LO)
excessively, step on it, place heavy objects on it, etc. A
damaged cord can easily become a shock or fire haz-
ard. Never use a power cord after it has been dam-
aged.
e In households with small children, an adult should
provide supervision until the child is capable of fol-
lowing all the rules essential for the safe operation of
the unit.
« Protect the unit from strong impact.
J
(Do not drop it!)
* Do not force the unit's power-supply cord to share)
an outlet with an unreasonable number of other
devices. Be especially careful when using extension
cords—the total power used by all devices you have
connected to the extension cord's outlet must never
exceed the power rating (watts/amperes) for the
extension cord. Excessive loads can cause the insula-
tion on the cord to heat up and eventually melt
through.
* Always turn the unit off and unplug the power cord
4
before attempting installation of the circuit board
(model no. CFX-1; p. 20).
Z\ |determined
by the design contained
within
the
@
must not be done is indicated by the design contained
@: indicated by the design contained within the circle. In
About the Symbols
The A symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The © symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The @ symbol alerts the user to things that must be
carried out. The specific thing that must be done is
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
ALWAYS OBSERVE THE FOLLOWING ----------------------2070700007
00>
Z\WARNING
* Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on the
"Information" page.
A\ CAUTION
¢ Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an out-
let or this unit.
¢ Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be placed
so they are out of the reach of children.
* Never climb on top of, nor place heavy objects on SO
the unit.
* Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from, an
outlet or this unit.
¢ Before moving the unit, disconnect the power plug
(yr
from the outlet, and pull out all cords from external
" ™ ®
devices.
¢ Before cleaning the unit, turn off the power and
4A
unplug the power cord from the outlet (p. 8).
-
« Whenever you suspect the possibility of lightning in €:
your area, pull the plug on the power cord out of the
outlet.
* Install only the specified circuit board(s) (model no. rt)
CFX-1). Remove only the specified screws (p. 20).
e When you mount the unit onto a rack, please be ZX
careful so that you won't pinch your fingers.

Advertisement

Table of Contents
loading

Table of Contents