FLYWOO CineRace20 DJI O3 HD V1.0 1/ drone introduction The CineRace20 O3 edition is currently the smallest cinewhoop of FLYWOO that is equipped with the DJI O3 Air unit module, measuring only 2 inch in size. It features neon LED lights, offering a variety of color options for added fun during races or other events.
Page 3
FLYWOO CineRace20 DJI O3 HD V1.0 Real Duct design This is a truly innovative duct design. It is designed to block certain winds, increasing the thrust of the drone. The duct completely surrounds the propeller, making flying safer.
Page 4
CineRace is double duct design , not a simple guard . It can fly as flexible as a racing drone, and as stable as Cinewhoop. Flywoo's classic compact design allows the CineRace20 and DJI O3 Air unit to be closely integrated.
Page 5
FLYWOO CineRace20 DJI O3 HD V1.0 Designing with a Focus on User Experience Multiple careful designs, convenient for your daily use Easy to adjust flight controller settings Built-in SanDisk microSD 128GB Easy to upgrade and read SD card function GOKU GM10 NANO GPS V3.0 Up to 30 satellites can be searched, making the rescue function more reliable.
Page 6
FLYWOO CineRace20 DJI O3 HD V1.0 Race neon LED, Buzzer alarm Allows you to control an LED light, turning it on or off as desired. It also offers a variety of color options, making it more fun to use during competitions or other events. (Changing the LED color requires soldering by yourself.
Page 7
FLYWOO CineRace20 DJI O3 HD V1.0 2/ Configuration and wiring diagram description Flight control wiring diagram PID and filter settings Lighter battery 4S 450MAH / 4S 750MAH Heavy battery 4S 900MAH or equipped with an action camera...
Page 8
FLYWOO CineRace20 DJI O3 HD V1.0 Default serial port settings UART1: ELRS/TBS/R9M/XM+/DSMX/SBUS receiver(Only open RX1) UART2: NULL UART3: GM10 NANO GPS (baud rate is 115200) UART4: DJI O3 UNIT OSD UART5: DJI O3 SBUS RX (Only use DJI remote control to turn on, and turn off RX1)
Page 10
FLYWOO CineRace20 DJI O3 HD V1.0 Bind procedure: - Supply power to the EL24E/EL24P rx, wait until the LED on the RX is off, immediately turn off the power, and then repeat again the above steps. When the RX is powered on...
Page 11
FLYWOO CineRace20 DJI O3 HD V1.0 3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver. 4/ Goggle binding: Use tweezers or a toothpick to press the O3 UNIT binding button, when the red light flashes, then press the goggles binding button to complete the binding.
Page 12
FLYWOO CineRace20 DJI O3 HD V1.0 5/ Mode setting: Set the ARM switch and flight mode switch, AUX* corresponds to the remote control switch, and the yellow area mark is turned on. 6/ Motor test: Before installing the propeller, test the rotation direction of the motor, turn on the safety...
Page 13
FLYWOO CineRace20 DJI O3 HD V1.0 7/ Install propeller Install the propeller in the correct direction, otherwise you will not be able to fly and damage the device, and finally fix the propeller with M2*6 screws 8/ USB upgrade O3 UNIT and export DVR video (built-in 128G...
Page 14
FLYWOO CineRace20 DJI O3 HD V1.0 8/ Filter installation (optional purchase) 8/ Flight firmware upgrade and write default CLI 1/ Activate DFU mode 2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may...
Page 15
FLYWOO CineRace20 DJI O3 HD V1.0 Driver software: https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe 3/ Then load the local HEX firmware and wait for the flashing to complete. A green progress bar is displayed to indicate completion, and DFU will become a COM port 4/ Factory CLI settings...