Advertisement
Quick Links
Advertisement
Related Manuals for Flywoo CineRace20 DJI HD
Summary of Contents for Flywoo CineRace20 DJI HD
- Page 1 FLYWOO CineRace20 DJI HD V1.0 CineRace20 DJI HD Manual...
- Page 2 CineRace is double duct design , not a simple guard anymore. . It can fly as flexible as a racing drone, and as stable as Cinewhoop. Pilots can quietly enjoy the fun of shooting a video without jelly and up to 12 minutes Super long flight time with Flywoo's latest 4S HV 900mah Battery !
- Page 3 FLYWOO CineRace20 DJI HD V1.0 Features 1. Almost all parts are injection molded. ABS\PC material. More sturdy and durable. 2. Very easy to disassemble and install, only fixed by two aluminum columns. 3. Pilots can freely combine their favorite colors to be more individual 4.
-
Page 4: Specification
Props: Gemfan D51 -5 HD digital camera & VTX: Caddx Polar Nano HD System Antenna: Flywoo Circular LHCP 5.8Ghz Ant ( UFL-Length: 115mm \ Tube 45mm ) Battery: Explorer 4S HV 300mAh / Explorer 4S HV 900mAh battery (Not including) - Page 5 FLYWOO CineRace20 DJI HD V1.0 Highly recommended battery Explorer 4S HV 300mah Battery （ You will get good flight time and fly quite flexible ） Explorer 4S HV 900mah Battery （ You will get a super long flight time, and the flight will be more stable ）...
- Page 6 FLYWOO CineRace20 DJI HD V1.0 PID and filter settings Default serial port settings...
- Page 7 FLYWOO CineRace20 DJI HD V1.0 UART1: ELRS/TBS/R9M/XM+/DSMX/SBUS receiver UART2: Bluetooth module, the default baud rate is 115200 UART3: NULL UART4: VISTA OSD TX/RX UART5: VISTA SBUS RX (Only use DJI remote control to turn on, and turn off RX1) UART6: NUL...
- Page 8 FLYWOO CineRace20 DJI HD V1.0 turn off the power, and then repeat again the above steps. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX enters the binding mode - Insert the 2.4G ELRS TX to Radio transmitter, and choose External RF mode to CRSF...
- Page 9 FLYWOO CineRace20 DJI HD V1.0 3/ To write the firmware of the R9MM receiver, you need to remove the R9MM receiver, and then write the firmware by connecting to the S.PORT port. 4/ After both R9M TX and R9MM RX are written into the ACCST firmware.
- Page 10 FLYWOO CineRace20 DJI HD V1.0 3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver. 4/ Mode setting: Set the ARM switch and flight mode switch, AUX* corresponds to the remote control...
- Page 11 FLYWOO CineRace20 DJI HD V1.0 5/ Motor test: Unload the propeller, test the rotation direction of the motor, turn on the safety switch, and test the rotation of the motors one by one. 6/ VISTA activation and binding Tip: For the convenience of use, VISTA has been activated by default at the factory and updated to the latest version of the firmware.
- Page 12 FLYWOO CineRace20 DJI HD V1.0 7/ Bluetooth function...
- Page 13 FLYWOO CineRace20 DJI HD V1.0 8/ Flight firmware upgrade and write default CLI 1/ Activate DFU mode 2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may be that the driver is not installed. The driver can be installed using IMPULSE RC software Driver software: https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe...
- Page 14 FLYWOO CineRace20 DJI HD V1.0 4/ After the connection is entered, it is a blank interface, you need to write CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual 5/ If the command is not restarted after writing the command, please write SAVE and...
- Page 15 FLYWOO CineRace20 DJI HD V1.0 6/ Then all functions of FC return to normal.
- Page 16 FLYWOO CineRace20 DJI HD V1.0 9/ Configuration table...