Advertisement
Quick Links
Advertisement
Related Manuals for Flywoo Firefly hex nano VISTA HD BF
Summary of Contents for Flywoo Firefly hex nano VISTA HD BF
- Page 1 FLYWOO Firefly hex nano VISTA HD V1.0 Firefly hex nano Manual VISTA HD BF Version...
- Page 2 FLYWOO Firefly hex nano VISTA HD V1.0 1/ drone introduction In an effort to push the boundaries of carry the camera on the smallest platform, Flywoo designed the smallest hexacopter possible in their history. Firefly Hex nano , a nano- sized fpv drone designed to carry Insta 360go ，SMO 4K camera for some action flying.
- Page 3 FLYWOO Firefly hex nano VISTA HD V1.0 2/ Configuration and wiring diagram description Specifications Item: Firefly hex nano hexacopter Weight: 57.9g (without battery) Wheelbase: 90mm FC & ESC : GOKU HEX F745HEX 16*16 STACK - ( FC+13A ESC ) Frame: Firefly hex nano Frame Motors: Robo 1202.5 5500KV...
- Page 4 FLYWOO Firefly hex nano VISTA HD V1.0 Target firmware：FLYWOOF745HEX UART1: TBS/R9M/XM+/DSMX/SBUS receiver UART2: NULL UART3: VISTA OSD TX/RX UART4: VISTA SBUS RX (Only use DJI remote control to turn on, and turn off RX1) UART5: NULL UART6: NULL UART7: NULL...
- Page 5 FLYWOO Firefly hex nano VISTA HD V1.0 3/ Receiver binding TBS NANO 915: When the USB is connected, the green light of the receiver flashes, and then bind according to the picture operation. https://www.youtube.com/watch?v=-iNkVcOLITM&ab_channel=Danimal3D R9MM FCC ACCESS OTA： Make sure your remote control supports ACCESS protocol, then follow the link to register and bind https://www.youtube.com/watch?v=az5hDdNBcjg&t=9s&ab_channel=FrSkyRC...
- Page 6 FLYWOO Firefly hex nano VISTA HD V1.0 3/ To write the firmware of the R9MM receiver, you need to remove the R9MM receiver, and then write the firmware by connecting to the S.PORT port. 4/ After both R9M TX and R9MM RX are written into the ACCST firmware.
- Page 7 FLYWOO Firefly hex nano VISTA HD V1.0 3-1/ Then set the corresponding serial port and receiver protocol to ensure the normal output of each channel of the receiver. 4/ Mode setting: Set the ARM switch and flight mode switch, AUX* corresponds to the remote control...
- Page 8 FLYWOO Firefly hex nano VISTA HD V1.0 5/ Motor test: Unload the propeller, test the rotation direction of the motor, turn on the safety switch, and test the rotation of the motors one by one.
- Page 9 FLYWOO Firefly hex nano VISTA HD V1.0 6/ Flight firmware upgrade and write default CLI 1/ Activate DFU mode 2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may be that the driver is not installed. The driver can be installed using IMPULSE RC software Driver software: https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe...
- Page 10 FLYWOO Firefly hex nano VISTA HD V1.0 4/ After the connection is entered, it is a blank interface, you need to write CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual 5/ If the command is not restarted after writing the command, please write SAVE and...
- Page 11 FLYWOO Firefly hex nano VISTA HD V1.0 6/ Then all functions of FC return to normal.