Page 1
OWNER’S MANUAL X-MAX 125 ABS MOTORCYCLE Read this manual carefully before oper- ating this vehicle. YP125RA BL2-F8199-E1...
Page 2
XMTR COMP. (Hand Unit) Frequency band: 433.92 MHz The maximum radio frequency power: 10 mW Manufacturer: MITSUBISHI ELECTRIC CORPORATION, HIMEJI WORKS 840, Chiyoda-machi, Himeji, Hyogo 670-8677, Japan Importer: YAMAHA MOTOR EUROPE N.V. Koolhovenlaan 101, 1119 NC Schiphol-Rijk, 1117 ZN, Schiphol, the Netherlands...
Page 3
If you have any further questions, do not hesitate to con- tact your Yamaha dealer. The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first! Yamaha continually seeks advancements in product design and quality. There-...
Page 4
Important manual information EAU63350 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury haz- ards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Table of contents Safety information ......1-1 For your safety – pre-operation Further safe-riding points....1-5 checks ..........5-1 Description ........2-1 Operation and important riding Left view ..........2-1 points..........6-1 Right view........2-2 Starting the engine......6-2 Controls and instruments....2-3 Starting off ........6-3 Acceleration and deceleration ..
Page 6
Table of contents Lubricating the front and rear brake levers....... 7-23 Checking and lubricating the centerstand and sidestand ..7-24 Checking the front fork....7-24 Checking the steering....7-25 Checking the wheel bearings ..7-25 Battery .......... 7-26 Replacing the fuses...... 7-27 Headlights ........
Safety information an accident or equipment damage. EAU1026B See page 5-1 for a list of pre-operation checks. Be a Responsible Owner This scooter is designed to carry As the vehicle’s owner, you are re- the operator and a passenger. sponsible for the safe and proper oper- ...
Page 8
Safety information This scooter is designed for on- • Know your skills and limits. Staying within your limits may road use only. It is not suitable for help you to avoid an accident. off-road use. • We recommend that you prac- tice riding your scooter where Protective Apparel there is no traffic until you have...
Page 9
Safety information any engine exhaust. Deadly levels of The total weight of the operator, pas- carbon monoxide can collect rapidly senger, accessories and cargo must and you can quickly be overcome and not exceed the maximum load limit. unable to save yourself. Also, deadly Operation of an overloaded vehicle levels of carbon monoxide can linger could cause an accident.
Page 10
Genuine not in any way reduce ground Yamaha accessories, which are avail- clearance or cornering clearance, able only from a Yamaha dealer, have limit suspension travel, steering been designed, tested, and approved travel or control operation, or ob- by Yamaha for use on your vehicle.
Safety information Aftermarket Tires and Rims EAU57600 Further safe-riding points The tires and rims that came with your Be sure to signal clearly when scooter were designed to match the making turns. performance capabilities and to pro- Braking can be extremely difficult vide the best combination of handling, on a wet road.
Smart key system If you have an electric medical EAU76444 Smart key system device, consult a doctor or the The smart key system enables you to device manufacturer before us- operate the vehicle without using a ing this vehicle. mechanical key.
Smart key system In such situations, move the smart EAUM3960 Operating range of the smart key to another location and perform key system the operation again. If it still does The operating range of the smart key not work, operate the vehicle in system is about 80 cm (31.5 in) from emergency mode.
Smart key system tem does not operate, see page EAU78623 Handling of the smart key and 3-5 and confirm that the smart key mechanical keys is turned on. Placing the smart key in the front or rear storage compartment may block communication between the smart key and the vehicle.
Page 18
Do not submerge the smart key Yamaha dealer check the vehicle. If the smart key continually re- in water or other liquids. Do not place heavy items or ex- ceives radio waves, the smart key battery will discharge quickly.
You can register up to six smart EAU76471 Smart key keys for the same vehicle. See a Yamaha dealer regarding spare smart keys. If a smart key is lost, contact a Yamaha dealer immediately to prevent the vehicle from being stolen.
Smart key system This feature is convenient for locating EAU76482 Replacing the smart key bat- your vehicle in a parking lot and other tery areas. Replace the battery in the following sit- uations. To turn the answer-back beeper on The smart key system indicator or off light flashes for about 20 seconds The beeper, which sounds when the...
Page 21
Smart key system Do not expose smart key to ex- cessive heat, such as sunshine or fire. Chemical Burn Hazard - do not in- gest the battery. If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Smart key system EAU76892 trical systems will be switched off, Main switch which may result in loss of control or an accident. Do not push the main switch knob re- peatedly or turn the main switch back and forth beyond normal use. Other- wise, to protect the main switch from damage, the smart key system will temporarily disable and the smart key...
Page 23
Smart key system 2. Push the main switch knob and the smart key indicator light will When the main switch is turned to come on for approximately 4 sec- “OFF” but the smart key cannot be onds. confirmed (the smart key is either out- 3.
Page 24
Smart key system 2. While the smart key system indi- “OPEN” position, the smart key system cator light is on, turn the main beeper will sound under the following switch to “OPEN”. conditions. When the main switch has been in 3.
Page 25
Smart key system To lock the steering To use the “ ” position 1. Turn the handlebar all the way to 1. With the main switch in the “ ” the left. position and the smart key turned 2. With the smart key turned on and on and within operating range, within operating range, push the push the main switch knob.
Page 26
Smart key system Make sure that fuel tank cap lid is se- curely closed before starting off. 3-12...
If the warning light does not come on initially when the main switch is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the vehicle. EAU78171 ABS warning light “ ”...
Instrument and control functions braking. Have a Yamaha dealer EAU63544 Speedometer check the brake system and electri- cal circuits as soon as possible. The ABS warning light may come on while accelerating the engine with the vehicle on its centerstand, but this does not indicate a malfunction.
Instrument and control functions EAU63551 EAU78486 Tachometer Multi-function display ZAUM1534 ZAUM1481 1. Tachometer 1. Fuel meter 2. Tachometer red zone 2. Information display 3. Coolant temperature meter The electric tachometer allows the rid- 4. Clock er to monitor the engine speed and 5.
Page 30
If a problem is detected in the fuel The clock uses a 24-hour time system. meter, the all segments will flash repeatedly. If this occurs, have a To set the clock Yamaha dealer check the vehicle. 1. Turn the main switch to “OFF”.
Page 31
If serve tripmeter “F Trip” and start this occurs, have a Yamaha dealer counting the distance traveled from check the vehicle as soon as pos- that point.
Page 32
Instrument and control functions Odometer “Odo” tripmeter Fuel reserve tripmeter “F Trip” “Trip” The odometer shows the total distance traveled by the vehicle. The tripmeter shows the distance trav- eled since it was last reset. To reset the tripmeter, select it by pushing the “TRIP”...
Page 33
Instrument and control functions Oil change tripmeter “Oil Trip” V-belt replacement tripmeter “V- Belt Trip” ZAUM1488 1. Oil change indicator “Oil” ZAUM1543 2. Oil change tripmeter 1. V-belt replacement indicator “V-Belt” 2. V-belt replacement tripmeter The oil change tripmeter shows the distance traveled since the oil was last V-belt replacement...
Page 34
Instrument and control functions L/100 km → Consumption_ _._ km/L Information display → Consumption_ _._ L/100 km → Av- erage → Air-temp For the UK: Push the “TRIP” switch to change the display between the air temperature display “Air-temp”, battery voltage dis- play “Battery”, traction control system display “TCS ON”...
Page 35
2. Icy road warning indicator “ ” when using the start switch, have This display shows the air temperature a Yamaha dealer charge the bat- from –10 °C to 50 °C in 1 °C incre- tery. ments. If “---” appears in the battery volt- The icy road warning indicator “...
Page 36
If only “TCS” is displayed, there is a After resetting the average fuel con- communication error within the vehi- sumption, “_ _._” will be shown until cle. Have a Yamaha dealer check the the vehicle has traveled 1 km (0.6 mi). vehicle as soon as possible. Instantaneous...
Page 37
Instrument and control functions “H TEMP”: Appears when the top seg- ment of the coolant temperature meter If traveling at speeds under 10 km/h (6 starts flashing. If “H TEMP” is dis- mi/h), “_ _._” is displayed. played, stop the vehicle, then stop the engine, and let the engine cool.
Instrument and control functions ter position. To cancel the turn signal EAU1234M Handlebar switches lights, push the switch in after it has re- turned to the center position. Left EAU12501 Horn switch “ ” Press this switch to sound the horn. EAU54212 Stop/Run/Start switch “...
Instrument and control functions To use the “TRIP” switch, move the EAU12902 Front brake lever “TRIP/INFO” switch in direction (a). To use the “INFO” switch, move the “TRIP/INFO” switch in direction (b). 1. Front brake lever The front brake lever is located on the 1.
Instrument and control functions EAU12952 EAU78200 Rear brake lever The Yamaha ABS (Anti-lock Brake System) features a dual electronic con- trol system, which acts on the front and rear brakes independently. Operate the brakes with ABS as you would conventional brakes. If the ABS is activated, a pulsating sensation may be felt at the brake levers.
ABS is operating. How- ating on slippery surfaces, such as un- ever, special tools are required, so paved or wet roads. If sensors detect please consult your Yamaha deal- that the rear wheel is starting to slip (uncontrolled spinning), the traction ECA20100...
Page 42
The traction control system will auto- ble. matically disable under certain condi- 4. Have a Yamaha dealer check the tions; such as when a sensor fault is vehicle and turn off the “ ”...
Instrument and control functions EAU78502 Fuel tank cap To remove the fuel tank cap 1. Turn the main switch to “ ” to open the fuel tank cap lid. 1. Install mark “ ” 2. Close the fuel tank cap lid. EWA11092 WARNING Make sure that the fuel tank cap is...
Instrument and control functions EAU13213 dry, soft cloth, since fuel may Fuel deteriorate painted surfaces or Make sure there is sufficient gasoline in plastic parts. [ECA10072] the tank. 4. Be sure to securely close the fuel EWA10882 tank cap. WARNING EWA15152 Gasoline and gasoline vapors are WARNING...
Your Yamaha engine has been de- Make sure that the fuel tank over- signed to use premium unleaded gas- flow hose is not blocked, and oline with a research octane number of clean it if necessary.
Instrument and control functions EAU13447 EAU78514 Catalytic converters Storage compartments This vehicle is equipped with catalytic converters in the exhaust system. This model is equipped with 3 storage compartments. The front storage com- EWA10863 WARNING partments and rear storage compart- The exhaust system is hot after op- ment are located as shown.
Page 47
Instrument and control functions Storage compartment A To open storage compartment A, turn the main switch to “OPEN” and then push the “LID” button. To close storage compartment A, push the storage compartment lid until it is closed. Storage compartment B To open storage compartment B, push 1.
Instrument and control functions Since the storage compartment EAU78521 Windshield accumulates heat when ex- To suit the rider’s preference, the wind- posed to the sun and/or the en- shield height can be changed to one of gine heat, do not store anything two positions.
Page 49
Instrument and control functions 1. Bolt 1. Bolt 3. Remove the bolts, and then install Tightening torque: the bolts in the desired position. Windshield bolt: 8 N·m (0.8 kgf·m, 5.9 lb·ft) 5. Place the bolt access covers, and then install the quick fasteners. 1.
Page 50
Instrument and control functions Tightening torque: Windshield bolt: 8 N·m (0.8 kgf·m, 5.9 lb·ft) 5. Place the bolt access covers, and then install the quick fasteners. 1. Bolt 1. Bolt 4. Install the windshield to the low position by installing the bolts, and then tighten the bolts to the spec- ified torque.
The handlebar can be adjusted to one assemblies of two positions to suit the rider’s pref- EWA10211 WARNING erence. Have a Yamaha dealer adjust the position of the handlebar. Always adjust both shock absorber assemblies equally, otherwise poor handling and loss of stability may re- sult.
Instrument and control functions EAU78690 Ignition circuit cut-off system The ignition circuit cut-off system works with the sidestand switch and brake light switches. It has the follow- ing functions. It prevents the engine from start- ing when the sidestand is down. ...
Page 54
3. Keep the front or rear brake applied. • If a malfunction is noted, have a Push the start switch. Yamaha dealer check the system Does the engine start? before riding. The sidestand switch may not be working correctly.
Instrument and control functions 5. Insert the accessory plug into the EAU78213 Auxiliary DC jack auxiliary DC jack. EWA14361 WARNING To prevent electrical shock or short- circuiting, make sure that the cap is installed when the auxiliary DC jack is not being used. ECA15432 NOTICE The accessory connected to the...
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer. Before using this vehicle, check the following points:...
Page 57
• Tighten if necessary. Instruments, lights, • Check operation. — • Correct if necessary. signals and switches • Check operation of ignition circuit cut-off system. Sidestand switch • If system is not working correctly, have Yamaha dealer 4-26 check vehicle.
This model is equipped with a lean an- there is a control or function you do not gle sensor to stop the engine in case of understand, ask your Yamaha dealer. a turnover. In this case, the engine EWA10272 trouble warning light will come on but WARNING this is not a malfunction.
Operation and important riding points EAU78231 Starting the engine If the engine does not start, release the ECA10251 NOTICE start switch after 5 seconds. Before pressing the start switch again, wait 10 See page 6-5 for engine break-in in- seconds to allow battery voltage to re- structions prior to operating the ve- store.
Operation and important riding points EAU45093 EAU16782 Starting off Acceleration and deceleration 1. While pulling the rear brake lever with your left hand and holding the grab bar with your right hand, push the scooter off the center- stand. The speed can be adjusted by opening and closing the throttle.
Operation and important riding points EAU16794 Front Braking EWA10301 WARNING Avoid braking hard or suddenly (especially when leaning over to one side), otherwise the scooter may skid or overturn. Railroad crossings, streetcar rails, iron plates on road con- struction sites, and manhole Rear covers become extremely slip-...
The vehicle can now be operated nor- mally. ECA10311 NOTICE Keep the engine speed out of the tachometer red zone. If any engine trouble should oc- cur during the engine break-in period, immediately have a Yamaha dealer check the vehi- cle.
“OFF” or “ ”. Otherwise, the battery may discharge. The sidestand alarm beeper can be set to not activate. Please con- tact your Yamaha dealer. EWA10312 WARNING Since the engine and exhaust system can become very hot,...
Con- considered as a general guide under sult a Yamaha dealer for proper normal riding conditions. However, de- maintenance intervals. pending on the weather, terrain, geo-...
From 30000 km (17500 mi), repeat the maintenance intervals starting from 6000 km (3500 mi). Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills. EAU71060...
X 1000 mi 10.5 14 • Perform dynamic inspection us- Diagnostic system √ √ √ √ √ √ ing Yamaha diagnostic tool. check • Check the error codes. √ √ 2 * Air filter element • Replace. Air filter case √ √...
Page 68
Periodic maintenance and adjustment ODOMETER CHECK OR READING MAINTENANCE JOB ITEM X 1000 km X 1000 mi 10.5 14 Front and rear √ √ √ √ √ • Lubricate with silicone grease. brake lever pivot shaft • Check operation. Sidestand, center- √...
Page 69
Periodic maintenance and adjustment ODOMETER CHECK OR READING MAINTENANCE JOB ITEM X 1000 km X 1000 mi 10.5 14 Lights, signals and • Check operation. √ √ √ √ √ √ 27 * • Adjust headlight beam. switches EAU72790 Engine air filter and V-belt air filter •...
Periodic maintenance and adjustment EAU18752 Removing and installing the panel The panel shown needs to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time the panel needs to be removed and installed. ZAUM1507 1.
Do not attempt to diagnose such problems Tightening torque: Spark plug: yourself. Instead, have a Yamaha deal- 12.5 N·m (1.25 kgf·m, 9.22 lb·ft) er check the vehicle. If the spark plug shows signs of elec- trode erosion and excessive carbon or other deposits, it should be replaced.
Periodic maintenance and adjustment 5. Insert the dipstick into the oil filler EAUM3332 Engine oil hole, and then tighten the oil filler The engine oil level should be checked cap. before each ride. In addition, the oil must be changed at the intervals spec- To change the engine oil (with or ified in the periodic maintenance and without oil filter element replace-...
Page 73
Periodic maintenance and adjustment Tightening torque: Oil filter cover bolt: Skip steps 5–9 if the oil filter element is 10 N·m (1.0 kgf·m, 7.4 lb·ft) not being replaced. 5. Remove the oil filter element cover by removing the bolts. Make sure that the O-ring is properly seated.
Be sure no foreign material en- ride. If any leakage is found, have a ters the crankcase. Yamaha dealer check and repair the 12. Start the engine, and then let it idle scooter. In addition, the final transmis- for several minutes while checking sion oil must be changed as follows at it for oil leakage.
Periodic maintenance and adjustment EAU20071 Coolant The coolant level should be checked before each ride. In addition, the cool- ant must be changed at the intervals specified in the periodic maintenance and lubrication chart. EAU78580 To check the coolant level ZAUM0703 1.
Page 76
If water has been left floorboard mat by pulling it up. added to the coolant, have a Yamaha dealer check the anti- freeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced.
Periodic maintenance and adjustment EAUM3370 Left Air filter and V-belt case air fil- ter elements and check hoses The air filter element should be re- placed and the V-belt case air filter el- ement should be cleaned at the intervals specified in the periodic main- tenance and lubrication chart.
3.0–5.0 mm (0.12–0.20 in) NOTICE: Make sure that each Periodically check the throttle grip free filter element is properly seated play and, if necessary, have a Yamaha in its case. The engine should dealer adjust it. never be operated without the...
Therefore, it must be adjusted by a Yamaha dealer is essential to maintain the tires in good at the intervals specified in the periodic condition at all times and replace them maintenance and lubrication chart.
Page 80
Old and aged tires shall be wall is cracked, have a Yamaha dealer checked by tire specialists to ascertain replace the tire immediately. their suitability for further use.
If any damage is found, have model by Yamaha. a Yamaha dealer replace the wheel. Do not attempt even the Front tire: smallest repair to the wheel. A de-...
ZAUM1050 1. No brake lever free play There should be no free play at the brake lever ends. If there is free play, have a Yamaha dealer inspect the brake system. EWA14212 WARNING A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system.
Clean the filler cap before re- EAU22734 Changing the brake fluid moving. Use only DOT 4 brake Have a Yamaha dealer change the fluid from a sealed container. brake fluid every 2 years. In addition, Use only the specified brake flu- have the seals of the master cylinders id;...
EAU23098 Checking the V-belt Checking and lubricating the The V-belt must be checked and re- cables placed by a Yamaha dealer at the inter- The operation of all control cables and vals specified periodic the condition of the cables should be maintenance and lubrication chart.
The operation of the throttle grip Front brake lever should be checked before each ride. In addition, the cable should be lubricat- ed by a Yamaha dealer at the intervals specified in the periodic maintenance chart. The throttle cable is equipped with a rubber cover.
If the centerstand or sidestand does ECA10591 not move up and down smoothly, NOTICE have a Yamaha dealer check or re- If any damage is found or the front pair it. Otherwise, the centerstand or fork does not operate smoothly,...
If there is play in the wheel ward and backward. If any free hub or if the wheel does not turn play can be felt, have a Yamaha smoothly, have a Yamaha dealer dealer check or repair the steer- check the wheel bearings.
ZAUM1527 1. Negative battery lead (black) To charge the battery 2. Positive battery lead (red) Have a Yamaha dealer charge the bat- 3. Battery tery as soon as possible if it seems to have discharged. Keep in mind that the The battery is located behind panel A.
Periodic maintenance and adjustment 3. Fully charge the battery before in- EAU78242 Replacing the fuses stallation. NOTICE: When install- The main fuse and the fuse boxes, ing the battery, be sure to turn which contain the fuses for the individ- the main switch off, then con- ual circuits, are located under panel A.
Page 91
2. Remove the blown fuse, and then 4. If the fuse immediately blows install a new fuse of the specified again, have a Yamaha dealer amperage. WARNING! Do not check the electrical system. use a fuse of a higher amperage...
This model is equipped with LED-type headlights. auxiliary lights. If a headlight does not come on, have If an auxiliary light does not come on, a Yamaha dealer check its electrical have a Yamaha dealer check it. circuit. ECA16581 NOTICE Do not affix any type of tinted film or stickers to the headlight lens.
This model is equipped with an LED- If a front turn signal light does not type brake/tail light. come on, have a Yamaha dealer check If the brake/tail light does not come on, its electrical circuit or replace the bulb.
Replacing the license plate If a rear turn signal light does not come light bulb on, have a Yamaha dealer check the 1. Remove the license plate light unit electrical circuit or replace the bulb. by removing the bolts and plate,...
Please have the vehi- self. However, should your vehicle re- cle battery charged or replaced. quire any repair, take it to a Yamaha (See page 7-26.) dealer, whose skilled technicians have If the smart key system does not work...
Check the vehicle. compression. 4. Compression The engine does not start. There is compression. Have a Yamaha dealer check the vehicle. Operate the electric starter. There is no Have a Yamaha dealer check the vehicle. compression. 7-33...
Page 97
Start the engine. If the engine overheats again, The coolant level is have a Yamaha dealer check and repair the cooling system. If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
Periodic maintenance and adjustment EAU76561 Emergency mode When the smart key is lost or dam- aged, or its battery has discharged, the 868588 vehicle can still be turned on and the 868588 engine started. You will need the smart key system identification number. To operate the vehicle in emergency mode 1.
Page 99
Periodic maintenance and adjustment Release the knob after the smart key system indicator light flashes twice. ↓ The second digit has been set as “2”. ↓ Repeat the above procedure until all digits of the identification num- ber have been set. The smart key system indicator light will flash for 10 seconds if the correct identifi- cation number was entered.
Rust and corrosion can develop even if matte colored finished parts. Be high-quality components are used. A sure to consult a Yamaha dealer for rusty exhaust pipe may go unnoticed advice on what products to use be- on a car, however, it detracts from the fore cleaning the vehicle.
Page 101
Scooter care and storage structed. Also, thoroughly rinse compounds for plastic may the area off with water, immedi- leave scratches on the wind- ately dry it, and then apply a cor- shield. Test the product on a rosion protection spray. small hidden part of the wind- ...
Page 102
3. To prevent corrosion, it is recom- mended to apply a corrosion pro- Consult a Yamaha dealer for ad- tection spray metal, vice on what products to use.
Scooter care and storage head so that the electrodes are EAU36564 Storage grounded. (This will limit spark- ing during the next step.) Short-term d. Turn the engine over several Always store your scooter in a cool, dry times with the starter. (This will place and, if necessary, protect it coat the cylinder wall with oil.) against dust with a porous cover.
Page 104
Scooter care and storage Make any necessary repairs before storing the scooter.
Specifications Dimensions: Final transmission oil: Overall length: Type: 2185 mm (86.0 in) YAMALUBE 10W-40 or SAE 10W-30 type Overall width: SE motor oil 775 mm (30.5 in) Quantity: Overall height: 0.21 L (0.22 US qt, 0.18 Imp.qt) 1415/1465 mm (55.7/57.7 in) Coolant quantity: Seat height: Coolant reservoir (up to the maximum level...
Page 106
Specifications Caster angle: Rear brake: 26.5 ° Type: Trail: Hydraulic single disc brake 95 mm (3.7 in) Specified brake fluid: Front tire: DOT 4 Type: Front suspension: Tubeless Type: Size: Telescopic fork 120/70-15 M/C 56S Spring: Manufacturer/model: Coil spring MICHELIN/CITY GRIP Shock absorber: Rear tire: Hydraulic damper...
Page 107
Specifications High beam indicator light: Turn signal indicator light: Engine trouble warning light: ABS warning light: Smart key system indicator light: Traction control system indicator/warning light: Fuse(s): Main fuse: 20.0 A Main fuse 2: 7.5 A Terminal fuse 1: 2.0 A Signaling system fuse: 10.0 A Signaling system fuse 2:...
4-20.) Record the information on this label in the space provided. This information will be needed when order- 1. Vehicle identification number ing spare parts from a Yamaha dealer. The vehicle identification number is stamped into the frame. 10-1...
Privacy Policy. Privacy Policy https://www.yamaha-motor.eu/eu/ privacy/privacy-policy.aspx Yamaha will not disclose this data to a third party except in the following cas- es. In addition, Yamaha may provide vehicle data to a contractor in order to outsource services related to the han- dling of vehicle data.
Index Headlights ..........7-29 High beam indicator light ....... 4-1 ABS............4-14 Horn switch .......... 4-12 ABS warning light ........4-1 Acceleration and deceleration ....6-3 Air filter and V-belt case air filter Identification numbers......10-1 elements ..........7-14 Ignition circuit cut-off system....4-27 Auxiliary DC jack........4-29 Indicator lights and warning lights ..
Page 111
Index Throttle grip and cable, checking and lubricating .......... 7-23 Throttle grip free play, checking... 7-15 Tires............7-16 Tool kit............ 7-2 Traction control system......4-15 Traction control system indicator light... 4-2 TRIP/INFO switch......... 4-12 Troubleshooting ........7-32 Troubleshooting charts ......7-33 Turn signal indicator lights .....
Page 114
Original instructions MBK Industrie Z.I. de Rouvroy 02100 Saint Quentin SAS au capital de 14 000 000 € PRINTED IN FRANCE 2018.05 (E)