Kit Contents; Specification; Device Information - Texas Instruments LP-MSPM0C1104 User Manual

Evaluation Module Overview
1 Evaluation Module Overview
1.1 Introduction
The MSPM0C1104 is a low-cost microcontroller from the MSPM0 family based on the Arm(r) Cortex-M(r) M0+
processors architecture. These flexible devices can be used in a variety of system tasks from housekeeping
to simple motor control. The easiest way to get started with MSPM0C1104 is with the LP-MSPM0C1104
LaunchPad ™ . The LaunchPad has all the required features to load code, debug, and prototype right out of
the box.
To make prototyping even easier, TI provides the MSPM0 software development kit (SDK), which has over 50
code examples to use as starting points for application.
Free software development tools are also available, such as TI's
Workbench ™ IDE, and Keil
when paired with the MSPM0L1306 LaunchPad development kit. More information about the LaunchPad
development kit, the supported BoosterPack
the TI LaunchPad ™ development kit
software development kit (SDK), visit the
extensive online collateral, training with MSP Academy, and online support through the

1.2 Kit Contents

LP-MSPM0C1104 LaunchPad development kit
Quick start guide

1.3 Specification

LP-MSPM0C1104 is designed to be used in conjunction with a PC, Mac
Composer Studio ™ (CCS). CCS can run as a stand-alone on the workstation or be accessed through the web
(CCS Cloud) without the need for a software installation. Alternatively, LP-MSPM0C1104 ships with an example
loaded, which can be controlled by a GUI. See the out-of-box description below.
Once the code has been flashed onto LP-MSPM0C1104, the device can be powered from a power supply other
than the built in USB power supply. This allows the user to forgo the PC connection. Power can be applied
directly to either the 3.3V or 5 V rails. Do not apply power to both rails simultaneously. When using an external
power supply, make sure to not exceed 3.3V or 5 V respectively.

1.4 Device Information

LP-MSPM0C1104 uses the following devices from Texas Instruments.
Device Name
SimpleLink
MSP432E401YTPDT
CAN, 1MB Flash and 256kB RAM
ESD-protection array for high-speed data interfaces, 4
TPD4E004DRYR
channels
500 mA, adjustable, low quiescent current, low-noise, high-
TPS73533DRBT
PSRR, single-output LDO regulator
LM4040C25IDCKR Precision micropower shunt voltage reference
Mixed-signal
Microcontroller with 24 MHz Arm
MSPM0C1104SDGSR
16kB flash, and 1kB SRAM
2 LP-MSPM0C1104 Evaluation Module
® µVision ® IDE. Code Composer Studio IDE supports
™ plug-in modules, and the available resources can be found at
portal. To get started quickly and find available resources in the MSPM0
TI Cloud Developer
Description
™ 32-bit Arm ® Cortex ® -M4F MCU with ethernet,
® Cortex
Copyright © 2023 Texas Instruments Incorporated
Code Composer Studio
Zone. MSPM0 MCUs are also supported by
® , or Linux
XDS110 host device
Protect LP-MSPM0C1104 from ESD damage
through USB connector
3.3V power XDS110 and MSPM0C1104
Voltage reference for XDS110 debugger
® 32-bit-M0+ CPU,
Evaluation device
www.ti.com
™ IDE, IAR Embedded
EnergyTrace ™ technology
TI E2E ™ support forums.
® workstation running Code
Purpose
SLAU908 – OCTOBER 2023
Submit Document Feedback