Table of Contents
Advertisement
Available languages
Available languages
English
WARNING: Ensure the light panels are facing down before
stacking another ToughSystem 2.0 unit on top of the light
box to prevent possible activation of the LED lights.
This DWST08060 has a storage compartment
your extra batteries, cords or tools.
The adjustable work light
compartment
15
are ToughSystem® 2.0 compatible
and can be stacked together or individually with all
ToughSystem® 2.0 products.
1. To access the storage compartment
the adjustable work light
compartment
15
by pressing the stacking latch
and then lift the adjustable work light
storage compartment
2. To install the adjustable work light
compartment
15
, pivot the adjustable work light
slot
24
into the storage compartment slot
the adjustable work light
audible click is heard. Ensure the adjustable work light
is securely held in place.
Suspending the Adjustable Work Light
(Fig A, J)
CAUTION: When the adjustable work light hangs by the
hang hook, do not shake the adjustable work light or the
object from which it hangs. Do not hang the adjustable
work light from any electrical wires or anything that is not
secure. Personal injury or property damage may occur.
CAUTION: Only use the hang hook for hanging the
adjustable work light as shown in Fig. A, J. The hang
hook is not intended to support additional weight.
Do not attach or hang anything additional to the
adjustable work light or risk of breakage may occur.
CAUTION: Do not use the hang hook to reach with or
to support your weight in any situation.
CAUTION: Do not hang overhead. Serious personal
injury or damage to the adjustable work light may
result if the adjustable work light falls.
CAUTION: Do not mount the adjustable work light to
the ceiling.
nOTE: When using an extension cord to power the
adjustable work light
1
, locate the adjustable work light
within reach of an electrical outlet.
hang hook
The hang hook
11
may be used to suspend the adjustable
work light
1
from 2x4 lumber or pipes up to 2-1/2" (64 mm)
diameter.
1. The hang hook
11
folds out from under adjustable
work light
1
. Be sure to fully extend the hang hook
before using.
2. To store the hang hook
recess and ensure the hang hook
hang hook clasp
12
10
15
1
and the storage
15
first unlock
1
from the storage
1
off the
15
.
1
onto the storage
25
1
down and inward until an
fold it into the hang hook
11
clips into the
11
.
Mounting the Adjustable Work Light Using
the Threaded Accessory Mounts (Fig. A, K)
WARNING: Since accessories, other than those offered
to carry
by D
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
If you need any assistance in locating any accessory, please
contact your nearest D
www.D
e
The DWST08060 is equipped with 1/4 x 20
13
5/8 x 11
21
to accommodate current or future D
1. Place the mounting screw of the accessory into the
appropriate threaded mount
accessory to the adjustable work light
. Press
nOTE: Follow the directions included with
the accessory.
1
2. Ensure the light is securely attached.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before making
any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Your D
WALT product has been designed to operate over
e
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
care and regular cleaning.
Storage and Transportation
•
Always store with battery removed and disconnected from
the AC power supply!
•
Avoid using the DWST08060 outdoors or transporting in an
open vehicle.
•
Do not use in rain. Do not expose to rain.
•
Store indoors..
•
Store the DWST08060 in a place that is as cool and dry
as possible.
•
Store the DWST08060 in a place where it cannot be
1
accessed by children or unauthorized persons.
•
Check the DWST08060 for damage before use after long
periods of storage.
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
11
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
WALT, have not been tested with this product, use
e
WALT service center or go to
e
WALT.com.
female threaded mount. This threaded mount is
WALT recommended
e
20
and
WALT accessories.
e
20
,
21
and secure the
1
.
Advertisement
Table of Contents
