Intelix DigiCat Series Installation Manual

Frequently Asked Questions
How do I expose the individual pairs in Cat 5 cabling?
There is no single method when exposing the four individual pairs in twisted pair cabling, such
as Cat 5 and Cat 6; however, it does help to have a cable stripping tool designed to strip the
cable jacket/insulation.
Begin by stripping back the cable's outer jacket/insulation about an inch (or more depending
on whether multiple baluns will be connected to the pairs of a single cable) so that the internal
wires are exposed. Be careful not to cut the internal wires when stripping the insulation/
jacket. Eight twisted wires and a string should now be visible; the string is unnecessary and may
be removed. These eight wires, which when combined form four pairs, connect directly to the
baluns. Typical protocol pairs similar colors; the important thing is to verify the same color-
coded pairs are used on each end.
How do I crimp an unshielded RJ45 connector onto Cat 5?
Crimping an RJ45 connector onto Cat 5 is a fairly straight forward task, assuming you have
the proper tools. Keep in mind that baluns require either the EIA/TIA 568A or 568B crimp
pattern, which are the industry standards for networking.
1. First, strip a portion of the insulation about 3/4" to expose the four twisted pairs.
2. Next, untwist the wires and fan them out so that they match either EIA/TIA 568A or
568B pattern.
3. Evenly trim the wires to about 1/2". Most RJ45 crimp tools feature a built-in wire
trimmer.
4. Insert the trimmed wires into the RJ45 connector so that each wire is in its individual
slot. Verify each wire is completely inserted.
5. Finally, insert the RJ45 connector into the crimp tool and squeeze firmly.
6. Repeat the above steps on the other end of the Cat 5 cable and verify pinout is
identical on each end.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix DIGI-VGA-F VGA and Audio over Cat 5 Balun Set
Installation Manual Installation Manual
Installation Manual Installation Manual Installation Manual
The Intelix DIGI-VGA-F balun set transmits high-definition VGA video and high-fidelity
analog audio extended distances over inexpensive structured pair cabling, such as Cat 5 and
Cat 6. The DIGI-VGA-F balun set includes a DIGI-VGA-S-F send balun, a DIGI-VGA-
R-F receive balun, two power supplies, and a USB power cable. The kit is powered on
both the send and receive end with either 12 VDC power supplies or optional USB power
on the send end. The send balun provides a local audio/video outputs for added versatility,
whereas the receive balun features dual amplified audio/video outputs for linking. In
addition, the DIGI-VGA-R-F receive balun provides brightness, contrast, and overall
picture quality adjustment for skew-free performance over standard Cat 5 cabling.
The Intelix DigiCat Series of baluns is the ideal solution for sending high-performance
audio and video signals over structured cabling. When signal quality matters, choose
Intelix.
Installation
Caution: Do not attempt to disassemble or alter the balun housing. There are
no user-serviceable parts inside the DIGI-VGA-F. Modifying the unit
will void your warranty.
To install a DIGI-VGA-F balun kit, perform the following steps:
1. Turn off power and disconnect the source and destination equipment by following
the device manufacturer's instructions.
2. Make certain that outlets and cross connects to which you will connect the DIGI-
VGA-F are configured properly and labeled appropriately to identify the circuit.
Caution: Do not connect the DIGI-VGA-F to a telecommunication outlet wired
to unrelated equipment. Making such a connection may damage the
equipment and/or balun. Please ensure all wiring is "straight-through."
3. Verify the desired twisted pairs are not being used for other LAN or telephony
equipment.
4. Connect the VGA and audio outputs from the source equipment to the DIGI-
VGA-S-F send balun. If desired, connect a local monitor and audio outputs.
Caution:
Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
5. Connect the VGA and audio inputs from the destination equipment to the DIGI-
VGA-R-F receive balun.
6. Connect the two baluns with a structured cable with RJ45 connectors, such as
Cat 5. Verify the cable's pinout conforms to EIA/TIA 568A or 568B pattern
standards.
7. Power on the source and destination equipment and test for correct operation.
8. If required, adjust the brightness and contrast settings on the DIGI-VGA-R-F
receive balun.