Advertisement
3. Turn the pool so the drain valve is near the area where your plan to
drain the water.
ATTENTION:
order to avoid puncturing from sharp objects.
4. Insert the stopper plug into the inlet and outlet on the wall of the
pool from the inside of the pool. (See Fig. 8)
5. Insert top rail (A) into the pole pockets at the top of the pool.
(See Fig. 1)
6. Connect top rail (A) with T-Connector (C) at each of corner and
insert pins (D) into pre-drilled holes of the frame. (See Fig. 2, 3)
7. Repeat steps 5 and 6 until all top rails (A) are connected with all
T-Connectors (C) and the top frame is set up.
NOTE:
For ease of assembly slightly raise the last 2 rails to
an inverted v shape and insert into the last T-Connectors(C). Slowly
lower until fully connected taking care not to pinch your fingers.
(See Fig. 4)
8. Connect vertical pool leg (B) into the bottom of the T-Connector (C).
(See Fig. 5)
NOTE:
Make sure the hole on the vertical pool leg (B) is
facing outward.
9. Attach all footings (E) to the bottom of the vertical pool legs (B).
(See Fig. 6)
10. When the pool is completely assembled pull the frame from
different directions to ensure all rails, pool legs and connectors are
firmly jointed. (See Fig. 7)
11. Ensure drain valve is firmly closed. Smooth out the bottom.
12. Insert the 8 Tent legs (K) to the 8 T-Connectors (C) (See Fig. 9)
13. One fiberglass pole (L) has 3 sections. Extend the fiberglass pole
by pulling out each section and place it into the metal ferrules.
14. Insert one end of the pre-extend fiberglass pole to the Tent leg (K),
the other end to the Sprayer (F). Repeat this step for the other
fiberglass poles. Make sure the 8 fiberglass poles form a
semidome. (See Fig. 10)
15. Spread the tent's outer cloth (O), make sure the center is above on
the Sprayer (F), adjust the tent's outer cloth (O) position until the
sewing lines are superposed to the fiberglass poles (L). Hook the
tent's outer cloth (O) to the hole of the vertical pool leg (B).
(See Fig. 11)
16. Tie the outer cloth (O) to the fiberglass pole (L) by using the 3 pairs
ropes at the inner of outer cloth (O). The rope can also fix the hose
(M).
17. Smooth out all wrinkles on the outer cloth and make it perfect.
IMPORTANT:
cover the floor. Once pool floor is slightly covered, gently smooth
out all wrinkles. Start in the center of the pool and work your way
clockwise to the outside.
NOTE:
Drawings for illustration purpose only. May not reflect
actual product. Not to scale.
Fig. 1
Fig. 3
Fig. 5
POOL MAINTENANCE
If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your children.
Using chemical tablets (not included):
Do not drag the pool on the ground in
Put 1in. to 2in. water in the pool to
Fig. 2
Fig. 4
Fig. 6
Fig. 7
Fig. 9
Fig. 1 1
FILLING POOL WITH WATER
ATTENTION:
with water.
1. Fill the pool until the water reaches the welding line located
2.0in-7.9in (5cm-20cm) from the top of the pool. DO NOT
OVERFILL as this could cause the pool to collapse. In times of
heavy rainfall you may need to empty some of the water to ensure
the level is correct.
2. When filling the pool is completed, check that the water is not
collecting on any side to ensure the pool is level.
IMPORTANT:
re-level ground by digging out. Never attempt to move the pool with
water in it, serious personal injury or damage to the pool may result.
WARNING:
pressure. If your pool has any bulge or uneven side then the pool is
not level, the sides may burst and the water may discharge
suddenly causing serious personal injury and/or damage to
property.
3. Check pool for any leaks at valves or seams, check any evident
water loss. Do not add chemicals until this has been done.
6
Fig. 8
Fig. 10
Do not leave pool unattended while filling
If pool is not level, drain water and
Your pool may contain a great deal of
2.0in-7.9in
(5cm-20cm)
0°
Advertisement
