Storage - Scheppach MFH4200-4BP Translation Of Original Instruction Manual

Contact the manufacturer if the cutter continues to
run at idle.
Do not continue to operate the unit!
The user is responsible for all damages caused
by non-compliance with instructions in this
manual.
This also applies to non-authorized modifica-
tions of the tool, use of non-authorized spare
parts, accessories, working tools, unrelated and
not intended use, secondary damages due to
use of faulty components.
Wear Parts
Even when used in the intended way, some compo-
nents are subject to normal wear. They have to be
replaced depending on the kind of duration of usage.
These parts include, among others, the cutting tool
and the retaining disk.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement
parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always
use the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 450
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.4
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.4
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain ProCut 3/8.50-39
Guide rail ProCut AL10-39-507P
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
42 | GB
Hedge trimmer:
Blade for hedge trimmer 390 mm
Transport guard for blade

11. Storage

Cleaning
• Keep handles free of oil, so you always have a se-
• Clean the equipment as required with a damp cloth
m Important!
• Always pull out the spark boot plug each time be-
• Never immerse the equipment in water or other liq-
• Store the petrol multi garden tool in a safe and dry
Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the follow-
ing steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can
cause problems when starting up the equipment and
may require expensive repairs.
1 Slowly remove the fuel tank cap to release any
2 To remove the fuel from the carburetor, start the
3 Leave the engine to cool (approx. 5 minutes).
4 Remove the spark plug (see section 10 Change
7910700701
7910700702 5 Add one teaspoon of 2-stroke engine oil into the
3904801065
7910700705
3904801066
7910700711
3904801066 Note: Store the equipment in a dry place and far
3904801023 away from possible ignition sources such as an oven,
a gas-fired hot water boiler, a gas-fired dryer, etc.
7910100732
7910100731 Putting the equipment back into operation
7910700704 1 Remove the spark plug (see section 10 Change
3904801037
3904801039 2 Quickly tug on the starter cord to remove excess
7910700710
www.scheppach.com
cure hold.
and, if necessary, mild washing up liquid.
fore carrying out any cleaning.
uids in order to clean it.
place out of the reach of children.
pressure that may have formed in the tank. Care-
fully empty the tank. Only ever empty the tank out-
doors or in well-ventilated rooms. Make sure not
to spill fuel or chain oil into the soil (environmental
protection). Use a proper base.
engine and let it run until the equipment stops.
and clean the spark plug).
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
and clean the spark plug).
oil from the combustion chamber.
7910700703
3904801043