Table of Contents
Advertisement
Motor Specifications
and Electrical Requirements
1
_ower Supply
and Motor Specifications
WARNING:
To avoid
electrical
hazards,
fire haz-
ards or damage
to the tool, use proper circuit pro-
tection.
Your
tool
is wired
at the
factory
for
operation
using
the voltage
shown.
Connect
toot
to a power line with the appropriate
voltage and a
15-amp branch
circuit.
Use a 15-amp time delay
type fuse or circuit breaker. To avoid shock or fire,
if power cord is worn or cut, or damaged in any
way, have it replaced
immediately.
The A-C motor used in this tool is a relay start, non-revers-
ible type, having the following specifications:
Rated H P
1
Voltage
110-120
Amperes
1 t 5
Hertz (Cycles)
60
Phase
Single
RPM
3450
Rotation of Shaft Counterclockwise
i ,,u
..............
General
Electrical
Connections
DANGER: To avoid electrocution:
1. Use only identical
replacement
parts when ser-
vicing,
Servicing
should
be performed
by a
qualified service technician.
2, Do not use in rain or where floor is wet.
This tool
is intended
for indoor residential
use
......... only.
7
WARNING:
Do not permit fingers to touch the ter- |
minals
of plug when
installing
or removing
the
plug to or from the outlet.
110-120 Volt, 60 Hz. Tool Information
NOTE: The plug supplied on your toof may not fit into the
outtet you are planning to use Your local electrical code
may require slightly different power cord plug connec-
tions
if these differences
exist refer to and make the
proper adjustments
per your local code before your tool
is plugged in and turned on
In the event of a malfunction
or breakdown,
grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock
This toot is equipped
with an electric cord having an equipment-grounding
con-
ductor and a grounding plug, as shown,, The plug must
be plugged
into
a matching
outlet that is properly
installed and grounded in accordance with all local codes
and ordinances
Do not modify the plug provided, If it will not fit the outlet,
have the proper outlet installed by a qualified electrician
A temporary adapter may be used to connect this plug to
a 2-prong outlet as shown if a properly grounded three
prong outlet is not available,. This temporary
adapter
should be used only until a properly
grounded three
prong outlet can be installed by a qualified electrician
The green colored
rigid ear', lug or the like, extending
from the adapter
must be connected
to a permanent
ground such as a properly grounded outfet box
Improper connection
of the equipment-grounding
con-
ductor can result in a risk of electric shock The conduc-
tor with insulation having an outer surface that is green
with or without yellow stripes is the equipment-grounding
conductor
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-ground-
ing conductor to a live terminal
If the grounding instructions
are not completely
under-
stood, or if you are in doubt as to whether the tool is prop-
erly grounded check with a qualified electrician or service
)ersonnel.
WARNING: If not properly
grounded, this tool can
cause an electrical shock, particularly
when used
in damp locations, in proximity to plumbing, or out
of doors_ If an electrical shock occurs there is the
potential
of a secondary
hazard,
such as your
hands contacting the sawblade.
Properly
Grounded
3-Prong Outlet
\ J
In
111
3-Prong Plug
G!ounding
Prong
Grounding
Lug
_
Make sure this
Is Connected
to a Known
Ground
2-Prong
Outlet
NOTE: The adapter illustrated is for use only if you
already have a properly grounded 2-prong outlet
7
Hide quick links:
Advertisement
Table of Contents
