Pro-Craft VB20 Manual page 5

5 EN | ENGLISH
◊ Maintain labels and nameplates on the appliance. These carry
important safety information.
◊ People with pacemakers should consult their physician(s) before
use. Electromagnetic fields in close proximity to heart pacemaker
could cause pacemaker interference or pacemaker failure.
◊ The warnings, precautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
KNOW THE INTELLIGENT CONTROL PANEL
Left battery indicator
Air speed indicator
Lower speed button
ON/OFF button
ASSEMBLY INSTRUCTION
WARNING:
Use of a product that may have been improperly assembled could result in
serious personal injury.
WARNING:
If any parts are damaged or missing do not operate this product until the
parts are replaced. Use of this product with damaged or missing parts
could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not
recommended for use with this product. Any such alteration or modification
is misuse and could result in a hazardous condition leading to possible
serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to
comply could result in accidental starting and possible serious personal
injury.
ASSEMBLING/ DISASSEMBLING THE THREE-PIECE
BLOWPIPE
WARNING:
Never use the leaf blower with only one blowpipe section attached. There
is a risk of personal injury!
◊ Assemble the three-piece blowpipe (5) as illustrated (Fig.2). The
parts can be felt to lock into place
◊ Now push the blowpipe (5) on to the blowing aperture of the motor
housing (1) until the blowpipe (5) latches into place. (Fig. 3)
◊ Dismantle the blowpipe (5) by pressing the locking button (6) and
pulling off the blowpipe
ASSEMBLING/DISASSEMBLING THE THREE-PIECE
SUCTION PIPE
WARNING:
Never use the leaf blower with only one suction pipe attached. There is a
risk of personal injury!
◊ Open the protective cover (3) of the suction aperture by pressing
the locking of the suction aperture (4) in the direction of the suction
aperture and pulling out the protective cover, turning it clockwise
until it stops. You can now remove the protective cover (3). ( Pic..4)
◊ Assemble the three suction pipes as illustrated ( Pic. 5). When
assembling, pay attention to the guide grooves on the suction pipe
parts.
◊ Place the suction pipe (12) on the suction aperture, as in Pic..6
◊ Dismantle the suction pipe (12) by pressing the lock of the suction
INSTALLING /REMOVING THE COLLECTION BAG
In suction mode the device must only be operated with the collection bag
mounted. The ventilation opening on the collection bag (11) serves for an
improved air circulation.
Right battery
◊ If necessary, remove the blowpipe (5) (see "Assembling/dismantling
indicator
◊ Now push the collection bag (11) on to the blowing aperture of the
Higher speed button
◊ Hook the carabiner (10) of the collection bag into the eyelets
The additional handle (7) can be locked in various positions.
TURBO speed button
◊ Press the angle adjuster (13) on the additional handle (7).
◊ Adjust the additional handle to the desired position.
◊ Release the angle adjuster (13).
PUTTING ON THE CARRING BAG
Never wear the carrying strap diagonally across your shoulders and chest:
only wear it on one shoulder to ensure you can detach the device quickly
from your body in the event of danger.
◊ Place the carrying strap on one shoulder.
◊ Adjust the strap length so that the snap hook is approximately 10
◊ Attach the snap hook on the eyelet to insert the strap
MAINTENANCE
In order to avoid personal injury and the risk of fire and electric shock,
remove the battery pack before adjusting, inspecting, or cleaning the
blower.
When servicing use only identical parts. Use of any other parts could create
a hazard or cause product damage.
◊ Be alert for battery packs that are nearing their end of life. If you
◊ Ventilation openings and switch levers must be kept clean and
◊ Avoid using solvents when cleaning plastic parts. Most plastics are
◊ Our machines have been designed to operate over a long period
◊ In order to maintain battery capacity, we recommend the battery to
Emptying the Collection Bag
With full collection bag, the suction pumping capacity decreases
considerably and the collection bag must be emptied when the bag is full
or interferes with the suction capacity of the device.
1. Turn off the device and wait until the impeller has stopped.
2. Remove the batteries from the device.
(below). Turn the suction pipe anticlockwise until it stops. Push the
suction pipe into the motor housing until it clicks into place.
aperture (4) in the direction of the suction aperture and pulling out
the suction pipe, turning it clockwise until it stops. You can now
remove the suction pipe.
WARNING:
the three-piece blowpipe").
motor housing (1) until it latches with the locking button (6).
provided on the motor housing.
WARNING:
cm below your hip.
WARNING:
WARNING
notice decreased tool performance or significantly shorter running
time between charges then it is time to replace the battery pack.
Failure to do so can cause the tool to operate improperly or damage
the charger.
free of foreign matter. Do not attempt to clean by inserting pointed
objects through opening.
susceptible to damage from various types of commercial solvents
and may be damaged by their use. Use clean clothes to remove dirt,
oil, grease, etc.
of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper machine care and regular cleaning.
be completely discharged everyone month and fully recharged again.
Only store with a fully charged battery and top-up the charge from
time to time if stored for a long time. Store in a dry and frost-free
place, the ambient temperature should not exceed 40°C.