Advertisement

Quick Links

700JN (Natural Gas) & 700JP (Propane Gas)
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
▪ If you cannot reach your gas supplier,
call the fi re department.
— Installation and service must be
performed by a qualifi ed installer, service
agency or the gas supplier.
4006264-03
©2017, Miles Industries Ltd.
Legend G3.5
Direct Vent Gas Insert
Installation and Owner's Manual
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
L e a v e t h i s m a n u a l
w i t h t h e a p p l i a n c e .
R e t a i n t h i s m a n u a l
f o r f u t u r e r e f e r e n c e .
Please read this manual
BEFORE installing and
operating this appliance.
This manual contains instructions to install the
ENGINE ONLY. A front is also REQUIRED to
complete this installation. A barrier screen is pro-
vided with the front. Refer to the manual sup-
plied with the front for installation.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Ce guide est disponible en français sur demande.
Patent Pending
I N S TA L L E R
C O N S U M E R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 700JN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Valor 700JN

  • Page 1 Legend G3.5 Patent Pending Direct Vent Gas Insert 700JN (Natural Gas) & 700JP (Propane Gas) Installation and Owner’s Manual DANGER I N S TA L L E R L e a v e t h i s m a n u a l HOT GLASS WILL w i t h t h e a p p l i a n c e .
  • Page 2: Table Of Contents

    fi tter in the State assumes no responsibility for any consequential of Massachusetts. damage(s). Designed and Manufactured by / for Miles Industries Ltd. 190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com © Copyright Miles Industries Ltd., 2017...
  • Page 3: Safety Precautions

    Safety Precautions READ and UNDERSTAND all instructions carefully Due to the high temperature, the appliance should be before starting the installation. FAILURE TO FOLLOW LOCATED out of traffi c areas and away from furniture these installation instructions may result in possible fi re and draperies.
  • Page 4: Safety And Your Fireplace

    Child Safety Precautions and Recommendations, A physical barrier is strongly • recommended if there are young Parts of your Valor Fireplace become • children, or at-risk individuals in the extremely hot while in operation. house. Install an approved after- The glass viewing window •...
  • Page 5: Owner's Information

    EXTREMELY HOT!!! gas heater is a technical appliance that must be installed by a qualifi ed dealer. Each Valor fi replace is fully tested during • READ the SAFETY information on pages the production process for your safety and comfort.
  • Page 6: Cleaning Your Fireplace

    OWNER’S Owner’s Information INFORMATION Cleaning Your Fireplace To remove the window for cleaning: 1. Unhook the trim WARNING with the barrier screen. DO NOT TOUCH THE GLASS WHILE IT IS HOT! Let the fi replace cool fi rst before cleaning it. 2.
  • Page 7 fi replace, damage components, cause overheating resulting in dangerous conditions. Damage caused by incorrect window installa- tion is not covered by the Valor warranty. 6. If the Hot Glass Warning plate has been removed from the front lower corner of the window, reinstall it by sliding it between the glass and the frame as indicated.
  • Page 8: Checking Pilot And Burner Flames

    OWNER’S Owner’s Information INFORMATION Checking Pilot and Burner Flames The appliance area must always be kept clear and free from combustible materials, gasoline and other A periodic check of the pilot and burner fl ames should fl ammable vapors and liquids. be made.
  • Page 9: Replacing Batteries

    OWNER’S Owner’s Information INFORMATION Replacing Batteries Locating Lighting, Operation and Rating Information Card WARNING WARNING DO NOT ATTEMPT TO CHANGE THE BATTER- IES WHILE THE FIREPLACE IS STILL HOT! Let DO NOT ATTEMPT TO TOUCH THE DATA CARD the fi replace cool fi rst before touching it. WHILE THE FIREPLACE IS STILL HOT! Let the fi...
  • Page 10: Operating Your Fireplace

    OWNER’S Owner’s Information INFORMATION Operating Your Fireplace Manual ON/OFF Switch: Press the O button. There are three ways to control your fi replace. 1. Thermostatic Remote Control; 2. Wall Switch (optional); 3. Manual On/Off Switch. Manual ON/OFF Switch As well, familiarize yourself with the gas shut-off valve location in your house.
  • Page 11: Remote Control Operation

    OWNER’S Remote Control Operation INFORMATION NOTE: Before using the remote control system for IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and the fi rst time, the receiver and the handset must be automatic ON/OFF can only be programmed when synchronized.
  • Page 12 OWNER’S Remote Control Operation INFORMATION • Press and hold (small fl ame) MODES OF OPERATION button to decrease fl ame height or • Briefl y pressing the SET button to set the appliance at pilot fl ame. changes the mode of operation in •...
  • Page 13 OWNER’S Remote Control Operation INFORMATION SETTING THE ON / OFF TEMPERATURES • - Nighttime Setback T E M P Temperature Mode (Appliance SETTING THE “DAYTIME” TEMPERATURE must be in standby mode; pilot ignited) - The room temperature Default Settings: (sun), 23ºC / 74ºF TEMP is measured and compared to the Nighttime Setback temperature.
  • Page 14 OWNER’S Remote Control Operation INFORMATION SETTING THE “NIGHTTIME SETBACK” TEMPERA- SETTING PROGRAM TIMERS TURE • You can program two periods of time between 12:00 Default Settings: (moon), “ ” (OFF) T E M P am and 11:50 pm in each 24-hour cycle. •...
  • Page 15 OWNER’S Remote Control Operation INFORMATION SETTING P1 OFF TIME SETTING P2 ON TIME • Briefl y press SET to scroll to TIMER mode • Briefl y press SET button to scroll (sun) while the time fl ashes. to TIMER (moon) while the •...
  • Page 16: Options

    Optionnal Accessories* 706RGL Refl ective glass panels Gas Conversion Kits 707FBL Fluted panels 700JNGK Conversion to natural gas 708VRL Valor Red brick panels Barrier 700JPGK Conversion to propane gas Front Screen Other Accessories Floating Trim 3-sided 710BPB Backing plate black 37-3/4” x 26-7/8”...
  • Page 17: Lighting Instructions

    OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING : If you do not follow these instructions exactly A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To save gas, turn the pilot off when not using the appliance for a prolonged period of time.
  • Page 18: Specifi Cations

    Vented Gas Fireplace Heaters for use in Canada Supply Gas and USA, and to CGA 2.17-91 High Altitude Standard Heater engine 700JN is used with natural gas. in Canada. This appliance is for direct vent insert Heater engine 700JP is used with propane gas.
  • Page 19: Overview

    QUALIFIED Overview INSTALLER This appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of non-combustible material. DO NOT install into combustible construction. This appliance is NOT APPROVED for installation with a zero clearance kit. WARNING Chimney Terminal Cap Some materials or items, although...
  • Page 20: Dimensions

    QUALIFIED Dimensions INSTALLER 28-5/8” (727 mm) 21-1/4” (540 mm) Fan box: 6’ (1.8 m) Fan power cord 3” (76 mm) Optional fan 3” 3” 9” (76 mm) (76 mm) 13” (228 mm) (330 mm) 13” 4” Trim (102 mm) (102 mm) (sold separately) 9-1/2”...
  • Page 21: Clearances

    QUALIFIED Clearances INSTALLER WARNING Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the fi replace. Avoid placing candles, paintings, photos, and other items sensitive to heat around the fi replace. Combustible Mantel Clearances Mantel Pro- 0-6”...
  • Page 22: Venting

    QUALIFIED Venting INSTALLER Typical Vent Installation See the Approved Venting Accessories list on page 41 of this manual. NOTE: Flexible co-linear vent pipes may only be installed into existing non-combustible solid-fuel burning fi replaces and chimneys. Terminal Cap Vent Location The vent terminal must be located above the roof.
  • Page 23: Existing Fireplace Preparation

    QUALIFIED Installation Planning INSTALLER Only qualifi ed licensed or trained personnel should install this appliance. Installer—READ THIS FIRST 1. YOU NEED TO KNOW FROM THE 13. Refi t window. HOMEOWNER what accessories (surround, 14. Reinstall the hot glass warning plate if it has been screen, fan/blower, etc.) will be installed with removed.
  • Page 24: Installation

    QUALIFIED Existing Fireplace Preparation INSTALLER Gas Line Routing Combustible Mantels Plan the routing of the gas line before proceeding. Combustible mantel clearances must conform to those Utilize the existing hole for the gas line of the factory- required for the original solid-fuel fi replace into which built fi...
  • Page 25: Remove Window

    QUALIFIED Installation INSTALLER Remove Window The window is held in place by a spring-loaded lever on each side. 1. To remove the window, locate the levers on each side of the window towards the top. Using your fi nger, pull the lever towards you and unhook it from the window frame bracket.
  • Page 26: Connect Venting

    QUALIFIED Installation INSTALLER Connect Venting IMPORTANT: This appliance’s venting system is room sealed and there- fore, does not require room air to be used in the combustion process. 1. Rough-in two 3” diameter vent liners into the existing chimney system from the roof. Be careful not to tear or damage the liners in the process.
  • Page 27: Connect Gas Supply

    QUALIFIED Installation INSTALLER Connect Gas Supply The appliance must be isolated from the gas supply piping system by closing its equipment shut-off valve The gas supply inlet connection is a 1/2” NPT female. A during any pressure testing of the gas supply piping gas shut-off...
  • Page 28 QUALIFIED Installation INSTALLER Inlet Connection 2. Install alternate elbow (not supplied). The appliance is sup- plied with a fl ared elbow 6-3/8” (162 mm) connector fi tted onto the 3/8” street elbow(s) valve and a fl ex connec- (where allowed) tor supplied loose to be attached to the elbow connector.
  • Page 29: Install Liner Panels

    QUALIFIED Installation INSTALLER Install Liner Panels 5. Rotate the anchor up and out of the way and slide the left hand side panel against the fi rebox side. The following guidelines apply to all panels except Rotate the anchor back down to hold the panel. 706RGL Refl...
  • Page 30: Install Ceramic Logs

    QUALIFIED Installation INSTALLER 9. Reinstall the front brick support. 11. With logs only: Install the front bricks in front of the burner. 10. Reinstall the rear log support (3 screws). Its rear 12. With logs only: Slide the cast iron grate in the edge rests on the rear brick support ledge.
  • Page 31 QUALIFIED Installation INSTALLER 2. Place the black glass piece, smooth side up, on 4. Place the right front log with its left end fl at on the top of the burner and move it forward to rest in the glass. The notch in the log should place squarely on grooved recess of the grate and center it.
  • Page 32 QUALIFIED Installation INSTALLER 6. Isntall the top right log. Place its wider end on the front right log’s peg and rest its narrow end in the notch on the rear log. 7. If desired, add loose embers on top of the front bricks between the legs of the grate in the shaded space.
  • Page 33: Install Ceramic Rocks

    QUALIFIED Installation INSTALLER Install Ceramic Rocks Unpack the ceramic rocks very carefully to avoid damaging them. Install the rocks as shown. Please note that the position of some of the rocks identifi ed in the following instructions is critical to ensure proper performance of the appliance.
  • Page 34 QUALIFIED Installation INSTALLER 5. Identify rocks number 1, 2, 3, 4 and 5. These rocks 8. Identify the rocks 7, 9, 11 and 14. These rocks have pegs that fi t in the holes on top of the rock have one hole underneath and fi t on the peg of base.
  • Page 35: Install Side Shrouds

    QUALIFIED Installation INSTALLER 11. Optional: Lay the twigs on the rocks. They can be IMPORTANT: The rocks of the top row (14, 11, 9 and placed as suggested below or elsewhere on the slightly 7) overhang over the burner. rocks as long as they do not block the pilot fl ame or the burner fl...
  • Page 36: Refi T And Check Window

    Bottom railing Damage caused by incorrect window installa- tion is not covered by the Valor warranty. 6. If the hot glass safety plate has been removed from the front of the window, put it back in place as indicated.
  • Page 37: Synchronize Remote Control

    QUALIFIED Installation INSTALLER Synchronize Remote Control 5. With a sharp object, press and hold the receiver’s reset button until you hear one short and one long The receiver and the handset of the remote control beep. Release the reset button after the second system must be initially synchronized before the fi...
  • Page 38: Check Operation

    QUALIFIED Installation INSTALLER Check Operation In a few unusual installations, the fl ame picture may be improved by adjusting the aeration. The need for Turn the fi replace fl ame up and down using the adjustment should be determined only by operating the remote control to confi...
  • Page 39: Install Handset Wall Holder

    QUALIFIED Installation INSTALLER Install Handset Wall Holder Alternative 2 Alternative 3 Packing Contents: The remote control kit for this fi replace comes complete with a wall-mounted holder. 1 Wall Bracket A This holder is not required in all installations 2 Screws B 1 Screw C but is provided as an optional feature for 2 Wall Anchor D...
  • Page 40: Wiring Diagram

    QUALIFIED Wiring Diagram INSTALLER Optional Wall Switch Kit 1265WSK Connector Yellow Optional Fan Remote 795CFKV2 Battery Box Control Module 4 AA Batteries GV60 MAX Wiring Diagram...
  • Page 41: Approved Venting Components

    QUALIFIED Approved Venting Components INSTALLER Approved Direct Vent Suppliers for Valor Models 700, 739 , 780, 785 and RF24DV Venting Parts Code / availability by Manufacturer Venting Parts Description 4DVC 940264 HSDV4658- Standard Co-axial 46DVA-VC 4DT-VC TM-4VT — 4DH-1313 —...
  • Page 42: Warranty

    The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase. Alternatively, the warranty registration form may be fi lled out online at www.valorfi replaces.com. b) Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation instructions.
  • Page 43: Spare Parts

    OWNER’S Spare Parts INFORMATION Part Part Code Description Code Description Number Number AutoFire Exhaust slide assembly 4006540 34” fl ex pipe with shut-off valve 4002475 Exhaust slide gasket 4001662 Inlet elbow connector 4002909 Valve access cover 4002806 Ignition cable 500 mm 4001039 Access panel gasket 4002664...
  • Page 44 LH Twig 4001827 Ceramic black 4003204 RH Twig 4001828 Ceramic black 4003204 Enamel platform 4003231EB Valor red brick 4003222 Platform base 4003230BY GV60 Valve repair kit 4004544 #8 - 32 Hexagonal nut plated (2) 4001517 Liner panels—complete set Ledgestone 705LSL Refl...
  • Page 45 OWNER’S Spare Parts INFORMATION 54 - 55 59 58 60 71 72 Natural gas Propane gas 80, 80a 17 - 23 41 40...
  • Page 47 Thank You ... For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed installer. Please fi ll in the information below. The information provided will be used for customer records only.
  • Page 48 Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...

This manual is also suitable for:

Legend g3.5700jp

Table of Contents