Aqara Smart Lock U100, SDL-D01, DL-D01D - Fingerprint Keyless Entry Door Lock with Apple Home Key Manual

Product Introduction

U100 is an IoT-enabled smart lock that supports multiple unlocking methods, such as fingerprint, password, NFC card and Apple Home Key, etc. Through in-depth customization of the fingerprint module and deep optimization algorithm, it provides a smooth experience of unlocking the door through fingerprints. The door lock can be configured through the Aqara Home app. Along with other Aqara smart devices, it can realize various smart automation for your connected home, and provide you with a convenient and safe experience.

* An Aqara Hub is required. Some functions require specific models of the Aqara Hub. Please visit www.aqara.com/en/support.html for more details.

What's in the Box

Keyhole Sliding Cover
Tips:
Use the key to unlock it after gliding the cover plate

Enter Button/Locking Button
Note: Click the button to lock the door after the plate is awakened.

Reset Button
Long press for 3 seconds to reset.
Note: It will clear previous users setting.

HomeKit Button
Press to connect with iOS devices

Note: It will clear previous users setting.

Instructions before Installation

Before using this product, you need to download the Aqara Home app and register an account. No such operations are required if you directly connect this product with the Apple Home app, however, unique features such as fingerprint recognition, auto-lock, and others will not be able to be experienced.

Aqara Home
Sign up for Aqara Home account, then add Smart Lock U100 and follow the app installation tutorial to install.

Installation Videos
Or scan the following QR code to check the installation video.

A PH1 standard Phillips head screwdriver is required for installation.

Tools necessary only for new doors or adjusting existing door holes: Drill, Hole Saws, Wood Mortise Chisel, Pencil, Tape Measure, Level

Device Installation

1. Measure the backset: the distance from the edge of the door to the center of the deadbolt hole. It should be 2 ⅜ in (60 mm) or 2 ¾ in (70 mm).
   
2. Adjust the latch according to the measurements
   
   Install directly if it's 2 3/8 in (60mm)
   
   If it's 2 3/4 in (70mm), rotate the latch 180 degree to extend the length.
3. Fix the latch. Make sure that the "TOP" is facing up.
   
4. Install the strike plate to the door frame.
   
5. Pass the outer panel connector cable through the deadbolt inside the door and strengthen the outer panel with the mounting plate and opposite-pull screw.
   
   
   After installation, please rotate the tailpiece to check if it is smooth when locking or unlocking. If there is a jam, please check if the tailpiece is placed in the center of the mounting plate opening and if there is no interference with other parts.
6. Remove the battery cover, then take off the knob cover with the removal tool.
   
7. Fix the connector cable of the outer panel to the inner panel.
   
8. Fix the inner panel to the mounting plate indoors and cover the knob.
   
9. Once the battery installed successfully, a voice prompt will be played to indicate the installation is completed.
   

Preparation before Use

1. A smartphone or tablet that supports Wi-Fi or a cellular network (with iOS or Android system) is required.
2. Please make sure that there is a 2.4G Wi-Fi connection and your internet connection is stable.
3. Please open the battery cover and put in 4 AA batteries
   Note: It is recommended to use original batteries or alkaline batteries, as others may leak and thus cause damage to the product when used for a long time.
   
   Please replace the battery when it is low. Otherwise, verification and door opening will fail when the battery runs out. In this case, you can charge the lock with USB-C emergency power supply or unlock with the key.
4. Long press the "Reset" button for 3 seconds, and release the button after you hear the voice prompt. Then the reset completes.

Notes: The door lock cannot be locked normally as the user information will be cleared after reset. Please set the door lock by following instructions as soon as possible.

Device Binding & Initialization

Download the Aqara Home app: Search for "Aqara Home" in the Apple App Store or Google Play. Or scan the following QR code to download the Aqara Home app.

Open the app, tap "+" in the upper right corner of the homepage to enter the page of "Add the device". Choose "Smart Lock U100" and then install the door lock device according to the instructions.

The actual operations are subject to change due to the updates of the Aqara Home app. Please following the instructions of the app.

Add the User

Enter the page of the door lock device and add the door lock owner according to the instructions on the app.
Notes: The door lock cannot be locked normally without adding users.

Add the Device to HomeKit (for iOS users)

After the door lock is powered on for the first time, click "+" at the upper right corner of the Apple Home app in the iOS, select "Add Accessory" or open Aqara Home app. Tap "Bind HomeKit" in the "General Settings" column of the setting on the detail page of the door lock. Scan or manually input the HomeKit code as prompted (HomeKit code can be found when you open the battery cover of the indoor door lock). Then add users according to the instructions. HomeKit only supports the lock and unlock, smart automation setting and Apple Home Key.

Add to Apple Home Key (for iOS users)

After it is connected with HomeKit, one virtual door card will be automatically generated in the Apple "Wallet" app. You can use an iPhone or Apple Watch, which supports the Apple Home Key function to unlock by holding it close to the door lock.

Product Instructions

1. To control this HomeKit-enabled accessory, the latest version of iOS or iPadOS is recommended. Controlling this HomeKit-enabled accessory automatically and away from home requires a HomePod, HomePod mini, or Apple TV set up as a home hub. It is recommended that you update to the latest software and operating system.
2. To use home keys, iPhone XS or later with iOS 15 or later and Apple Watch Series 4 or later with watchOS 8 or later are required.
3. Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Connect Google or Alexa app

To unlock via Google or Alexa, please first, buy and bind the Aqara hub. For details, please scan the code and learn how to bind.

Product Specifications

Smart Lock U100

Model: SDL-D01 / DL-D01D
Wireless Protocols: Zigbee, Bluetooth 5.0, NFC
Powering Modes: 4 AA Batteries (6V ); USB-C Emergency Port (5V )
Dimensions: 5.3 × 2.9 × 3.5 in. (135.8 × 74.8 × 88.4 mm)
Operating Temperature: -35°C ~ 66°C (-31°F ~ 150.8°F)
Operating Humidity: 0 ~ 93% RH, no condensation