Wood Trim Finishing - U-Line Echelon Series Installation Manual

To insert a rack in the cabinet:
1. Align the left and right rack channels with the tracks
in the cabinet, and ensuring an even track
engagement on both sides, gently push the rack into
the cabinet until it stops.
2. Before reloading the rack, ensure proper operation of
the travel stops in the left and right track rails by
pulling the rack out gently until it completely stops.

Wood Trim Finishing

The U-Line Beverage Center is equipped with wood-
trimmed wine racks that are coated at the factory with a
clear vinyl sealer, which will adequately protect the wood
in normal usage. A final finish coat was not applied so
that the wood trim could be stained to match décor. The
trim on the racks may be coated with a final finish or
stained.
To remove the wood trim surrounding the controller:
Figure 6
1. Loosen the two screws holding the controller to the
mounting bracket (Figure 6, 1).
2. Lift the controller housing (Figure 6, 4) and then
rotate forward to expose the wiring harness on the
back.
3. Disconnect the wiring harness from the controller
(Figure 6, 3).
4. Remove the two screws holding in the controller
housing (Figure 6, 2), then remove from wood.
Note: Carefully remove controller from housing. The glass
front is not secured to the controller. Glass may fall and
break, which is not covered under warranty.
5. After staining, installation is the reverse.
Be sure to align glass with controller when installing,
otherwise controller may not work correctly.
01/2007
2175BEV/2175BEVOL Beverage Center
To prevent permanent damage to the inner liner
of your unit, the wood trim MUST be removed
from the unit for staining and/or finishing. Allow
stain/finish to dry thoroughly (at least 24 hours
per coat) in accordance with the product
manufacturer's instructions prior to
reinstallation. Failure to do so may cause the
inner liner of the unit to have a permanent odor,
which is not covered by the warranty.
If staining the trim is desired, it must be done before the
application of any type of final finish. Review the
following staining/final finish and final finish-only
guidelines when staining/ and or sealing the wood to
ensure proper adhesion and durability of the finish.
Note: Glass in door is tinted. Stain may look darker
when door is closed.
Staining and final finish application:
1. Remove all screws securing wood trim to interior
2
3
1
DO NOT use oil-based stains on wood trim. Vapors from
oil-based stains will permanently penetrate the liner and
will not dissipate over time.
4
2. Apply Minwax
ULIN_0836_A
3. After two hours, repeat step 2. This will even out the
4. Allow stain to dry for a minimum of three hours before
5. If desired, sand the wood with very fine sandpaper to
6. Remove all dust from the wood, and apply one coat of
7. Allow the final coat to dry for 24 hours before
7
WARNING
components, and remove the trim from the cabinet
interior.
IMPORTANT
®
Water-Based Wood Stain to wood with
a synthetic bristle brush or a foam applicator. Allow
stain to penetrate approximately three minutes. Before
the stain is dry, take a stain dampened rag and remove
any excess stain remaining. Wipe in the direction of the
grain with medium pressure to achieve the desired stain
color.
color of the wood.
applying the final finish.
smooth the surface after the staining process.
® ®
Minwax Polycrylic Protective Finish using a synthetic
bristle brush to the wood. This finish should be applied
in a thin coat following the direction of the grain.
Apply the finish to the back and sides of the wood first,
and allow it to dry for two hours. Apply the finish to the
front side of the wood next, and allow it to dry for two
hours. Sand with very fine 220 grit sandpaper. Apply
two addition coats of the finish in the same manner, but
do not sand the trim after the final third coat is applied.
reinstalling the trim to the cabinet interior components.
www.U-LineService.com