The Stainless doors are not reversible. 2175BEVOL2 units are Black with a door that requires the construction of a 3/4-inch thick wood overlay frame. You must determine left- or right-hand opening before construction.
3 Prepare Site Your U-Line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for electrical connection in the rear.
60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 14. Environmental Requirements Many U-Line models are designed to operate in harsh outdoor/marine environments. Special considerations include the following: • The units are designed to operate between 50°F (10°C) 34 - 1/8"...
Side-By-Side Installation Instructions For a complete refreshment center, install your 2175BEVS or 2175BEVOL2 unit beside a U-Line Refrigerator, Ice Maker or Combo Model (see Figure 4 for typical cut-out). Note that each Side-By-Side Installation will be different. • Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide.
Wood Trim Finishing The U-Line Beverage Center is equipped with wood- trimmed wine racks that are coated at the factory with a clear vinyl sealer, which will adequately protect the wood in normal usage.
6. Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components. Reversing the Door (All U-Line units (except Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side.
Page 9
9. Tilt top of door into position in top hinge and install top hinge screw pin. 03/2008 2175BEV/2175BEVOL2 Beverage Center 10. Install metal hinge plugs removed in step 2 in old hinge holes (3 each, top and bottom). door pivot plate...
2175BEVS/2175BEVOL2 Beverage Center Overlay Frame (2175BEVOL2 Units Only) FRAME PREPARATION IMPORTANT The thickness of the wood overlay panel must be 3/4". Right-hand isometric view shown. Opposite for left-hand NOTE: Final component is only a picture frame. No panel inside of rails and stiles.
15). Be careful not to lose the door closer insert sets. Save pivot pin for use later. 03/2008 2175BEV/2175BEVOL2 Beverage Center 8. Carefully lay the door over the wood panel, making sure door is orientated correctly (top of door with top of wood overlay).
2175BEVS/2175BEVOL2 Beverage Center TAPE TOP OF OVERLAY Figure 17 12. Use the door frame holes as a guide to lightly punch pilot holes for the #6 x 1” pan head screws (Figure 18). Figure 18 13. Attach the door to the overlay using #6 x 1” wood screws.
2. With door upside-down, loosen but do not remove the two screws on the door’s bottom hinge plate. Figure 21 03/2008 2175BEV/2175BEVOL2 Beverage Center Slotted Mounting Holes Raise Outside Door Edge Figure 22 3. See Figure 22. If the top far edge of the door needs to move UP, move the hinge plate toward the outside of the door and retighten screws.
2175BEVS/2175BEVOL2 Beverage Center 6 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current).
6. Use a 1/8” drill to make two starter holes and fasten the Anti-Tip brackets to the floor using the screws provided. 03/2008 2175BEV/2175BEVOL2 Beverage Center Other hardware is required for floors made of materials other than wood. Marks on floor 7.
Who to Call Service Information If the need for service arises, call the U-Line Customer Care Center directly @ 800-779-2547. To ensure accurate assistance, please have your Model Number and Serial Number and an explanation of the problem. The Model and Serial Number plate is located inside unit at upper right hand corner.
Page 17
For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in ® ® undercounter icemakers, Combo...