Page 3
2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your 2175BEVS or throughout this guide: 2175BEVOL Beverage Center with a package inside...
Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft Your U-Line product has been designed for either free- cloth. Do NOT use abrasive cleaning agents. standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear.
60 Hz, 15A circuit (normal household current). See Overlay Electrical Specifications on Page 13. Environmental Requirements Many U-Line models are designed to operate in harsh outdoor/marine environments. Special considerations include the following: • The units are designed to operate between 50°F (10°C) 34 - 1/8"...
4 Prepare Racks and Door Frame Instructions The U-Line Beverage Center is equipped with wood- For a complete refreshment center, install your 2175BEVS trimmed wine racks that are coated at the factory with a or 2175BEVOL unit beside a U-Line Refrigerator, Ice Maker clear vinyl sealer, which will adequately protect the wood or Combo Model (see Figure 4 for typical cut-out).
Wood Trim Finishing which is not covered by the warranty. The U-Line Beverage Center is equipped with wood- If staining the trim is desired, it must be done before the trimmed wine racks that are coated at the factory with a application of any type of final finish.
2175BEVS/2175BEVOL Beverage Center Final finish-only application: To reverse the door: 1. Remove all screws securing wood trim to interior 1. Remove screws (3 each, top and bottom) from new components, and remove the trim. hinge location. Do not discard (see Figure 8).
2175BEV/2175BEVOL Beverage Center 5. If door has not been removed from cardboard packaging, carefully cut tape and remove from cardboard first. With bottom of door facing up, remove 3/4" pivot plate (2 screws), flip over, and remount on 13/16" opposite side of door (see Figure 11). Be sure angled side of plate faces center.
Page 10
2175BEVS/2175BEVOL Beverage Center 3. Create a relief for pivot plate by cutting notch in top 5. Drill hole for upper door hinge (top of frame) (see corner and coinciding back corner of overlay frame. Figure 15, Top View). Refer to Figure 15 for exact specifications.
Page 11
2175BEV/2175BEVOL Beverage Center Applying Foam Tape to Overlay Frame (If required) Door Tape Frame Inside Edge Incorrect Correct Overlay Frame Figure 18 Figure 20 1. Cut foam tape into four pieces, two pieces the width of the overlay frame and two pieces the height of the overlay frame.
2175BEVS/2175BEVOL Beverage Center 7. Starting at the corners and working toward the center, 5 Adjust Door push the door gasket back into place. Make sure gasket is seated on all four sides. Checking Door Alignment Installing the Door The unit’s door is aligned at the factory before shipment.
2175BEV/2175BEVOL Beverage Center 6 Prepare Power Supply Electrical Specifications Slotted Mounting CAUTION Holes Angled Edge Towards Center Electrical installation must observe all state and local of Door codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician.
2175BEVS/2175BEVOL Beverage Center 7 Level the Unit 8 Install the Unit Leveling Information Installation Troubleshooting Note: It is recommended that the unit is level. Problem 1. Use a level to check the levelness of the Beverage The door remains open unless it is pushed closed.
2175BEV/2175BEVOL Beverage Center Start-Up Troubleshooting 9 Start-Up for the First Time Problem Initial Start-Up Unit does not appear to turn on when plugged in. The unit is shipped with the control preset. No adjustments should be necessary at this time. For information about Solution Adjusting the Temperature Control, see the Use and Care Make sure outlet has power (circuit breaker has not...
For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in undercounter icemakers, Combo ®...