Water Hardness Setting - Krups EA810B70 Manual

Installation of the filter cartridge - total duration: around 2 min
To get the best taste from your coffee and extend your appliance's service life, we advise you to use only the Claris -
Aqua Filter System cartridge sold as an accessory.
Fig. 30 : Mechanism to indicate the month the cartridge was fitted and when to replace it (after 2 months at most).
Installing the cartridge in the appliance. On first use, screw the filter cartridge into the bottom of the water tank - Fig. 31.
Place a 0.6 l container under the steam nozzle.
button for more than 3 seconds (unless the appliance requires a 'CLEAN' and/or 'CALC' maintenance).
Press the
The indicator light flashes.
When the installation of the filter cartridge is finished, the indicator light
Your appliance is ready for the next use.
The Claris cartridge needs to be replaced after about every 50 litres of water or every two months at least. If you are
using the Claris – Aqua Filter System cartridge, set the water hardness to level 0.
Coffee temperature display
Appliances are pre-set in the factory to level 2.
Connect the appliance to the mains supply but do not switch it on.
Press the and buttons together, - Fig. 27.
The LED flashes during the setting phase.
Twist the knob to 20 ml to set the coffee temperature - Fig. 28.
Press the button to increase or touch the
Select the coffee temperature level: 1 LED lit = temperature 1, 2 LEDs lit = temperature 2, 3 LEDs lit = temperature 3,
the hottest setting.
To exit settings mode, press

Water Hardness Setting

Appliances are pre-set in the factory to hardness level 4.
Before using the appliance for the first time or after a change to the water hardness, it is advisable to set the appliance
to the correct water hardness. Contact your water supplier to find out the water hardness for your area.
Degree of
hardness Verv soft
° f
< 5,4°
°dH
°e < 3,75°
Connect the appliance to the mains supply but do not switch it on.
Press the and buttons together, - Fig. 27.
The LED flashes during the setting phase.
Twist the knob to 120 ml to set the water hardness - Fig. 28.
Press the button to increase or touch the
Select the level of water hardness to be used: 0 LEDs lit = very soft, 1 LED lit = soft, 2 LEDs lit = average hardness, 3
LEDs lit = hard, 4 LEDs lit = very hard - Fig. 29.
To exit settings mode, press
Setting the electrical supply cut-off mechanism
Appliances are pre-set in the factory to 1 hour.
You can program your machine's automatic shut-off following a pre-programmed number of hours.
Connect the appliance to the mains supply but do not switch it on.
buttons together, - Fig. 27.
Press the and
The LED flashes during the setting phase.
Twist the knob to 220 ml to set the automatic cut-off duration - Fig. 28.
Press the button to increase or touch the
Select the desired hardness: 1 LED lit = 1 hour, 2 LEDs lit = 2 hours, 3 LEDs lit = 3 hours, 4 LEDs lit = 4 hours - Fig. 29.
To exit settings mode, press
button to decrease the setting - Fig. 32.
.
0 1
soft
> 7,2°
< 3° > 4°
> 5°
button to decrease the setting - Fig. 32.
.
button to decrease the setting - Fig. 32.
.
becomes constant.
2
moderately hard
> 12,6°
> 7°
> 8,75°
3 4
hard extremely hard
> 25,2° > 37,8°
> 14° > 21°
> 17,5° > 26,25°
21