Advertisement
M2R Warrior, 18650 (3500mAh) Lithium battery, USB Magnetic Charging Cable, Holster, Lanyard, User Manual
Material: AL6061-T6 aluminum alloy unibody design with MilSpec Type-Ⅲ hard anodizing, along with blue bezel ring and stainless clamping ring on the switch.
Turbo | High | Med 1 | Med 2 | Low | Moon | |
1500 or 1000 700 LUMENS | 700 LUMENS | 250 LUMENS | 60 LUMENS | 15 LUMENS | 1 LUMENS | |
3 + 120 mins | 2 h | 6 h 15 min | 20 h | 70 h | 25 days | |
Turbo (1500lm) | Turbo (1000lm) | High | Med 1 | Med 2 | Low | |
10880 cd | 8200 cd | 5600 cd | 2150 cd | 780 cd | 260 cd | |
208 m | 180 m | 150 m | 93 m | 56 m | 32 m |
The tests are performed using one 18650 (3500mAh) Lithium battery.
Remove the product from the packaging. Before your first use, unscrew the tailcap and remove the insulating film within the battery compartment before screwing the tailcap back on tightly. If the battery needs to be changed, make sure that the negative polarity side of the battery faces toward the direction of the flashlight head (the side of the LED).
Before first use, unscrew the tailcap and take off the insulating film.
Charge the flashlight before use. Connect the USB end of the magnetic charging cable to an external USB power source (USB power source is not included in the package. Users can charge it through any USB power source such as a computer or wall adapter) and attach the other end to the tail cap of the flashlight. The indicator will glow red when it is charging, and glow green when it is fully charged or on standby.
If you are using this light for self-defense or need quick access to strobe mode for a better tactical experience, switch to the enhanced tactical operation mode before use.
SEE THE PICTURES BELOW TO SEE HOW TO SWITCH TO ENHANCED TACTICAL MODE:
ON/OFF: Single click the side switch to turn the light ON/OFF. When the light is turned on again, it will return to the previously memorized mode.
CHANGE BRIGHTNESS LEVEL: When the flashlight is on, press and hold the side switch and it will, starting from the present brightness level, automatically cycle through low, med2, med1, and high mode. The mode is selected when the side switch has been released. (Please note: moonlight and turbo are not in the automatic cycle).
MOONLIGHT MODE: When the flashlight is off, press and hold the side switch for over one second to access the moonlight mode. If the memorized mode is moonlight, simply click the switch to access it.
DIRECT ACCESS TO TURBO MODE: Quickly double click the side switch to access high mode. Double click the side switch again to enter turbo. (turbo will automatically be switched to high in three minutes).
STROBE: Quickly triple click the side switch to enter the strobe mode. To quit this mode, single click or press and hold the side switch.
LOCKOUT/UNLOCK: When the flashlight is off, press and hold the side switch (for about 2 seconds) to access the button lockout mode (the flashlight will enter the moonlight mode first and will then switch off to signal the lockout mode). Under the lockout mode, press and hold the side switch for less than one second. The red indicator below the side switch will be on for two seconds to signal that the light is still in lockout mode. To unlock it, keep holding the side switch for over one second until the moonlight mode is on again.
The tail switch features either standard or enhanced tactical operation modes.
SOFT PRESS: Turbo mode activated for momentary on (standard: 1,000 lumens; enhanced tactical: 1,500 lumens).
DEEP PRESS: Standard – Constant on turbo mode. Enhanced tactical – momentary strobe mode.
METHOD 1: Deep press the tail switch and hold it while clicking the side switch at the same time to shift between turbo for constant on (standard mode) and momentary strobe (enhanced tactical). Release the tail switch to stay on the setting you choose.
METHOD 2: When the flashlight is on, press and hold the side switch to cycle through low, medium, and high. After it cycles through 3 times, it will then cycle between turbo (standard mode) and strobe mode (enhanced tactical). Release side switch to stay on the setting you choose.
NOTE: If the battery used is not at least 6A, it will not support the 1,500-lumen turbo mode. If the tail switch has been set to enhanced tactical mode, the flashlight cannot be turned on via the tail switch. If this happens, to activate the tail switch, press and hold the side switch to set it back to the standard mode (follow method 2).
NOTICE
Technical Support Inquiries
techsupport@olightworld.us
Customer Service
customer-service@olightworld.com
cs@olightworld.us
Visit www.olightworld.com to see our complete product line of portable illumination tools.
Olight Technology Co., Limited
Address: 5th Floor, Building A2, Fuhai Information
Harbor, Fuhai Subdistrict, Bao'an District,
Shenzhen, China 518103
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download OLIGHT M2R WARRIOR - Tactical Performance Flashlight Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the M2R WARRIOR that isn't answered in the manual? Leave your question here.