Inateck BCST-20 - 2.4GHz Wireless Barcode Scanner Manual

Inateck BCST-20 - 2.4GHz Wireless Barcode Scanner Manual

Also See for BCST-20:

Advertisement

Inateck BCST-20 - 2.4GHz Wireless Barcode Scanner Manual

Introduction

  • USB wired + 2.4G wireless communication
  • Built-in FLASH memory, supports breakpoint resume
  • Can store 2600 pieces Code-128 codes under offline state
  • Supports Windows XP, Win7/8/10, Wince, mobile OS PC

Packing list

BCST-20 *1 unit
USB cable *1 pce
Wireless Adapter *1 pce
Quick Start Guide

Note: The device is not equipped with the charger, please charge the device via USB output charging equipment.

BCST-20 Barcode Scanner Overview

BCST-20 integrates high-performance processor and decoding board, it has fast decoding, high-precision reading ability, and high anti-interference ability. It can easily read barcodes on paper, goods and other media. The DOF has greatly improvement with similar products, also it has highly scanning speed, powerful reading ability with high accuracy.

Appearance:

  • 2.4G Wireless mode
  • USB Wired mode

Functions Setup:
BCST-20 Barcode Scanner change all the default functions setup through reading the setup barcodes.
Overview - Functions Setup

  • Scan the"Enter Setup" barcode
  • You can change your scanner setting by scan a certain barcode.
  • Scan the "Exit with Save" barcode to finish the setting.

Offline Mode

If you are heading for a working area which lies outside the Bluetooth signal range, you may activate the offline mode of the scanner, following the steps described below. Under this enhanced offline mode, all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them time and again to your liking.
Due to the fact that the data entries will be automatically wiped from the buffer memory during upload, a data loss is possible when malfunctions occur during upload, e.g. if the working station suffers a unanticipated system shut down.
An operation in offline mode is strongly recommended under the following scenarios:

  1. During the scanning process, the device often leaves the Bluetooth signal range;
  2. Due to a high quantity of blocking objects, the Bluetooth signal's stability can't be ensured.
  1. By scanning the following barcode, the offline mode will be activated.
    Offline Mode - Step 1 - Activation
  2. By scanning the following barcode, all data in the buffer memory will be deleted (only in offline mode).
    Offline Mode - Step 2 - Buffer data purge
  3. By scanning the following barcode, all data entries in the buffer memory can be manually uploaded after reconnecting to the working station (only in offline mode).
    Offline Mode - Step 3 - Manual data upload
  4. By scanning the following barcode, the gross quantity of the uploaded data entries will be summarised (only in offline mode).
    Offline Mode - Step 4
  5. By scanning the following barcode, the device leaves the offline mode, normal mode will be reinitialised.
    Offline Mode - Step 5 - Quit offline mode

Keyboard Language Setting

Read 'Enter setup' Barcode - 'Select your keyboard language' - Exit With save - Change your PC language as selected.
Keyboard Language Setting

Eg: Switching to German keyboard
Keyboard Language Setting - Example

Prefix and Suffix Setting

  1. Scan the "Enter Setup" barcode
    Prefix and Suffix Setting - Step 1
  2. Scan the "Prefix Setting" or "Suffix Setting" scanner
    Prefix and Suffix Setting - Step 2
  3. Scan certain barcodes sequentially to generate your own prefix/suffix. Example: If you want to add "#" as prefix or suffix, according to the barcode list provided on our website, you need to scan the "3" barcode first and then scan the "5" barcode.
    (Please refer to www.inateck.com for the number and symbol barcode list.)
    Prefix and Suffix Setting - Step 3
  4. Scan the "Exit with Save" barcode.

Performance Characteristics

Light Source (Laser) Laser LED 650+/-20nm
Decode Capability Codabar, Code 93, MSI, Code 128, UCC/ EAN-128, Code 39, EAN-8, EAN-13, UPC-A, UPC-E, ISBN, Industrial 25, Interleaved 25, Standard 25, 2/5 Matrix, USPS, FedEx
Resolution 3mil
Nominal Working Distance 6~30cm
Decode Rate 100 decodes per second
Scan width 30mm
Decode mode Single-Line Aiming
Scan mode Manual mode
Print Contrast Minimum 30%
Scan angles Roll 30° Pitch 75° Yaw65°
Cylinder Horizontal Scan Diameter 35mm
Indication Beeper, LED
Radio Range 10m Visual range
Interfaces Supported USB2.0
Processor ARM 772MHz
EEPROM 256K, can store thousands of barcodes
Wireless Communication 2.4G Wireless transmission
Battery 1800mAh lithium battery
Bluetooth Operating Frequency 2402-2480MHz
Bluetooth transmission Power 4dBm

Note:

  1. If you want to setup the function of BCST-20. Read 'Enter Setup' barcode, then 'Function Setup' barcode, and read 'Exit with Save' at last.
  2. Please remove the power and USB cable under thunderstorm weather, to avoid damage from thunder and lightning.
  3. Away heat source, keep ventilating.
  4. Pay attention to waterproof during storage, transportation and running.

LED Indicators

Indicator Colour Meaning
Blue LED on (1s) and off quickly Good Read, with one short beep (high tone)
Green, Flashing (On/Off ratio 1:1) Indicates the BCST-20 Scanner in Setting mode
Blue, Flashing (On/Off ratio 20ms: 3s) Indicates the BCST-20 Scanner establish a wireless connection successfully
Red, Charging indicator The red indicator will light during charging, and off when full charged.

Beeper

Beeping Meaning
One short beep, high tone Read barcode, with blue LED on (1s) and off quickly
One long beep, low tone Configuration error, with purple flashing; Or transmit buffer full, with green LED on and off quickly
Two short beeps, high tone Power off
Three short beeps, tone descending from high to low Enter or Exit Setting mode, with green LED flashing
Three short beeps, tone ascending from low to high Configuration correct, with green LED flashing

Common function Barcodes

Common function Barcodes

Function Setup Barcodes

(Note: the barcode with * is default setting of BCST-20)
Function Setup Barcodes

Features

  1. Supports a wide range of barcode types. FedEx and USPS barcodes are all supported.
  2. Anti-crash and anti-shock design.
  3. Ergonomic design. Up to 3 million keystroke life expectancy.
  4. Unrivalled battery life.
  5. Press to scan - powered by deep sleep mode.
  6. USB mode: 64 bit barcodes. 2.4G wireless mode: 57 bit barcodes.
  7. Prefix and suffix are allowed to be added. Reset to factory default settings by scanning the "Factory Reset" barcode.

FAQ

  1. Some barcodes cannot be read, why?
    1. Dirty or unclear barcodes might not be read.
    2. Digital barcodes displayed on phones, computers or tablets cannot be read.
    3. The possible reason is that the setting for some barcode types are not commonly used is off by default. You need to activate a specific barcode type to get it to work. Please feel free to contact our Customer Service Team for further assistance if you don't know the exact type of barcode that you are referring to.
  2. Is there any barcodes for apply or remove Enter for suffix?
    Yes, you can refer to the Common Function Barcodes to reverse the setting.
  3. The data cannot be sent to my computer or cellphone. Why?
    Please make sure if you have turned on the offline mode. Because it will store your scans internally instead of instantly transmitting them to the connected device. You need to scan the "Manual data upload" barcode to send the scanned codes to your connected device.
  4. Is the device compatible with android devices?
    Yes For Android User: an OTG Adapter is needed for devices without standard USB.
  5. How to solve the messy code problem encountered while using other foreign languages?
    The default language is English. Please refer to "Language Setting" chapter to change the setting.
  6. How to delete the extra character in the prefix or suffix?
    1. Scan code Prefix or Suffix Setting,
    2. Scan code"1""2""7" sequentially, then scan code "Exit with Save"

Note
If you receive an error of unable to transfer data via the wireless connection (Not applicable for the Offline Mode), please re-pair the scanner using the following steps. Please bear in mind that this process may take 3-15 seconds.
Re-pairing the scanner

Support

For any inquiries or comments concerning our products, please send an email to support@Inateck.com, and we will respond to you as soon as possible.

Contact Information
Company of License Holder
Shenzhen Licheng Technology Co,.Ltd
Add: Warehouse B, 1F, Building B, Dezhong Industrial Park,
No.11 Shibei Road,
Bantian Street, Longgang District, Shenzhen, Guangdong,
518000, China Tel: (+86)755-23484029

Manufacturer Information
Shenzhen Lixin Technology Co,.Ltd
Add: 1F, Building B, Dezhong Industrial Park, No.11 Shibei
Road, Bantian Street,
Longgang District, Shenzhen, Guangdong, 518000, China
Tel: (+86)755-23484029

USA
Tel.: +1 702-445-7528
Phone hours: Weekdays 9 AM to 5 PM (EST)
Email: support@inateck.com
Web: www.inateck.com
Addr.: Inateck Technology Inc, 6045 Harrison Drive Suite 6
Las Vegas, Nevada 89120

Germany
Tel.: +49 342-07673081
Fax.: +49 342-07673082
Phone hours: Weekdays 9 AM-5 PM (CET)
Email: support@inateck.com
Web: http://www.inateck.com/de/
Addr.: F&M TECHNOLOGY GmbH, Montgolfierstraße 6,
04509 Wiedemar

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Inateck BCST-20 - 2.4GHz Wireless Barcode Scanner Manual

Advertisement

Need help?

Need help?

Do you have a question about the BCST-20 and is the answer not in the manual?

Questions and answers

Table of Contents