ENACFIRE GEEK - Wireless Bluetooth Earbuds Manual

ENACFIRE GEEK - Wireless Bluetooth Earbuds Manual

Also See for GEEK:

Advertisement

ENACFIRE GEEK - Wireless Bluetooth Earbuds Manual

Customer Support

support@enacfireglobal.com (US/CA)
moongu@enacfireglobal.com (13K)
desupport@163.com(DE)
esenacfire@163.com (ES)

We will reply to you within 24 hours and 100% solve your issues

Packaging List

Product Overview

Product Overview

  1. Charging port
  2. Charging case LED light
  3. Multifunctional button
  4. Earphone LED
  5. Earphone mic
  6. Acoustic hole
  7. L/R logo
  8. Magnetic charging pin
  9. Speaker

Power On & Pairing

Approach 1 - With Charging Case

Take out earphones from the charging case
Approach 1 - With Charging Case - Step 1

Select 'ENACFIRE Geek' from Bluetooth list
Approach 1 - With Charging Case - Step 2

Approach 2 - Without Charging Case

Power On: Touch the earphones for 1 seconds
Prompt sound 'Power on'
Pairing: Right earphone Blue and White light flash
Select 'ENACFIRE Geek'
Note: Right earphone is the master earphone
Approach 2 - Without Charging Case

Incoming call

Answer call/End call
Tap the Left / Right earphone once

Reject call
Touch the Left / Right earphone for 2 seconds

Music

Pause / Play
Tap the Left / Right earphone once
(Some phones may require to start a media player first)

Voice Assistant
Tap the Left / Right earphone 3 times

Change Song
Double-tap the Left/Right earphone to next/previous song

Adjust Volume
Touch and hold the Left/Right earphone to decrease/increase volume

Power Off

Without Charging Case

Turn off Bluetooth to disconnect the earphones
Touch either one earphone for 8 seconds to power off both earphones
Without Charging Case

Single Mode

Single Mode Earphone
Without Charging Case Turn off both earphones
Touch the Left/Right earphone for 1 seconds enter pairing mode.
Select "ENACFIRE Geek" from Bluetooth list
Note: There will be two "ENACFIRE Geek" Bluetooth names for Left and Right earphones. Please select accordingly.

Charging

Earphones

Earphone LED Light Orc Charging
Earphone LEO Light Off Fully Charged
Note: It takes about 1.5 hours to fully charge the earphones

Charging Case

Put the earphones back to the case. Lights on charging case stand for the remaining battery capacity.
Note: It takes about I *5-2 hours to fully charge the charging case
Charging Case

Safety Instruction

Using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety. Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds,

Do not use earphones in thunderstorm weather the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning,

Earphones may not work properly under high temperature or high humidity conditions.

Do not use any corrosive cleaner/oil to clean the earphones. If the earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried.

Tips: Man-made damage and lost are not covered under warranty. Keep the earphones and the packaging out of reach of children.

Note

Please follow below steps when both earphones fail to pair with each other or occur connection related issues

  1. Place both earphones to charging case and remain charging
  2. Touch and hold the power buttons of both earphones for 8 seconds until Blue and White lights flash
  3. Wait for 5 seconds, take out both earphones from charging case
  4. Delete the 'ENACFIRE Geek' Bluetooth name from your phone and turn off Bluetooth
  5. Turn on Bluetooth and click 'ENACFIRE Geek' from your phone

Q&A

Q: Why the music cuts in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven / Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption. Note: Please keep your phone and the master earphone (R) as close as possible to ensure a more stable Bluetooth connection,

Q: What should I do if the earphones stop charging?
A: We recommend you to charge the earphones by using our cable. If our cable do not work, please try to use another charging cable or power source to charge the earphones.

Q: How to contact ENACFIRE Customer Service Team?
A: If you have any issue with the product, please contact us via support@enacfireglobal.com (LIS / CA) mooneu@enacfireglohal.com (UK)

We will reply to you within 24 hours and 100% solve your issue.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ENACFIRE GEEK - Wireless Bluetooth Earbuds Manual

Advertisement

Need help?

Need help?

Do you have a question about the GEEK and is the answer not in the manual?

Questions and answers

Table of Contents