Advertisement

ENACFIRE F2 - Manual

Packaging List

Product Overview

  1. Charging case LED Light
  2. Charging Port

Product Overview

  1. Multifunctional Button
  2. Earphone Mic
  3. Magnetic Charging Pin
  4. Earphone LED Light

Power On & Pairing

Approach 1 - With Charging Case

  1. Open the charging case cap
  2. Select 'ENACFIRE F2' from Bluetooth list
    Approach 1 - With Charging Case

Approach 2 - Without Charging Case

  1. Power On: Touch the earphones for 1 second. Release when you hear the prompt sound 'Power on' with White light on.
    Approach 2 - Without Charging Case
  2. Pairing: Earphones will pair automatically with Red and White light flash alternately
  3. Select 'ENACFIRE F2" from the device's Bluetooth list

Incoming call

Answer call/End call

Answer call/End call
Tap the Left / Right earphone once

Reject call

Reject call
Touch the Left / Right earphone for 2 seconds

Music

Pause/Play


Tap the Left/ Right earphone once to pause / play music in the music mode
(Some phones may require to start a media player first)

Voice Assistant


Tap the Left/ Right earphone 3 times, your device's Voice Assistant will be activated with the 'Beep' prompt sound

Next Song



Double-tap the Right earphone

Previous Song


Double-tap the Left earphone

Adjust Volume

Adjust Volume
Touch and hold the Left earphone to decrease volume
Touch and hold the Right earphone to increase volume

warning Note:
Above functions are not supported when the earphone is used in single, Prompt sound 'Beep' will be produced when the volume reaches minimum or maximum level.

Power Off

Mode 1 With Charging Case


Put the earphones back to the charging case and close the cap, they will power off automatically.

warning Note: Put either one earphone into the charging case, the another earphone will stay connected to the device,

Mode 2 Without Charging Case

Mode 2 Without Charging Case

  1. Turn off Bluetooth to disconnect the earphones
  2. Touch either one earphone for 8 seconds to power off both earphones

Single Mode

Single Mode Earphone
With Charging Case
  1. Take out Left' Right earphone from the charging case
  2. Select 'ENACFIRE F2' from Bluetooth list
Without Charging Case
  1. Make sure both earphones are turn off
  2. Touch the Left/ Right earphone for 1 second to turn on. Prompt sound 'Pairing will be produced with Red and White light flash alternately.
  3. Select 'ENACFIRE F2' from Bluetooth list

Charging

Earphones Charging Status

Open and close the charging case cap, wait for 5 seconds
Leftmost charging case LED light flashing: Left earphone charging
Rightmost charging case LED light flashing; Right earphone charging
Charging case LED lights off: Earphone Fully Charged

warning Note: It takes about 1.5 hours to fully charge the earphones

Charging Case Charging Status

Open and close the charging case cap
Lights on charging case stand for the remaining battery capacity

Charging Case Charging Status
1/3 Battery Left
2/3 Battery Left
Fully charged

warning Note: It takes about 1.5-2 hours to fully charge the charging case

Note

Please follow below steps when both earphones fail to pair with each other or occur connection related issues

  1. Turn off Bluetooth to disconnect the earphones
  2. Touch either one earphone to power off both earphones
  3. Touch and hold the power button of both earphones for 10 seconds with prompt sound 'Power on' first and then 'Power off'
  4. Put the earphones back to the charging case
  5. Delete 'ENACFIRE F2" Bluetooth name from your phone
  6. Turn on Bluetooth and reconnect the earphones

Q&A

Q: Why the music get cut in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven/Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption.
warning Note: Please keep your phone and the earphone as close as possible to ensure a more stable Bluetooth connection,

Q: What should I do if the earphones stop charging?
A: We recommend you to charge the earphones by using our cable, If our cable does not work, please try to use another charging cable or power source to charge the earphones.

Q: How to contact ENACFIRE Customer Service Team?
A: If you have any issue with the product, please contact us via:
support@enacfireglobal.com (US/CA)
moongu@enacfireglobal.com (UK)
We will reply to you within 24 hours and 100% solve your issues

Safety Instruction

Using earphones at high volume for extended periods of time will result in permanent hearing damage. It is advised to keep the volume level low at most of the time for your safety.
Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.
Do not use earphones in thunderstorm, the earphones may not work properly under poor weather condition, and may increase the risk of getting hit by lightning.
Earphones may not work properly under high temperature or high humidity conditions,
Do not use any corrosive cleanser/oil to clean the earphones. If the earphones come in contact with liquids, please quickly wipe it away. If it is submersed in the water, do not turn the earphones on until it is completely dried.

information Tips: Man-made damage and lost are not covered under warranty. Keep the earphones and the packaging out of reach of children.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ENACFIRE F2 - Manual

Advertisement

Need help?

Need help?

Do you have a question about the F2 and is the answer not in the manual?

Questions and answers

Table of Contents