ENACFIRE T1 - Wireless Earbuds Manual

Packaging List

Product Overview

1. Charging Case LED Light
2. Charging Port
   
   
3. Multifunctional Button
4. Earphone LED
5. Magnetic Charging Pin
6. Earphone Mic
7. Earphone Mic

Power On & Pairing

Approach 1 - With Charging Case

1. Take out earphones from the charging case
   
2. Select 'T1-R' from Bluetooth list
   
3. Click 'Pair' when the pop-up window display
   

Note: On IOS system, the device would like to pair with your iPhone may be either 'T1-L' or 'Headset'
On Android system, the device would like to pair with your phone will only be 'T1-L'

Approach 2 - Without Charging Case

1. Power On: Touch the earphones for 1 second Release when you hear the prompt sound 'Power on' with Blue light on.
2. Pairing: Earphones will pair automatically with Right earphone Blue and White light flash alternately
3. Select 'T1-R' from the device's Bluetooth list
4. Click 'Pair' when the pop-up window display

Note: Right earphone is the master earphone On IOS system, the device would like to pair with your iPhone may be either 'T1-L' or 'Headset'
On Android system, the device would like to pair with your phone will only be 'T1-L'

Incoming call

Answer call/End call

Tap the Left / Right earphone once

Reject call

Touch the Left / Right earphone for 2 seconds

Music

Pause / Play

Tap the Left / Right earphone once to pause / play music in the music mode
(Some phones may require to start a media player first)

Voice Assistant

Tap the Left / Right earphone 3 times, your device Voice Assistant will be activated with the 'Beep' prompt sound

Next Song

Double-tap the Right earphone

Previous Song

Double-tap the Left earphone

Adjust Volume

Touch and hold the Left earphone to decrease volume
Touch and hold the Right earphone to increase volume

Note:
Above functions are not supported when the earphone is used In single Prompt sound 'Beep' will be produced when the volume reach minimum or maximum level

Power Off

Mode 1 With Charging Case

Put the earphones back to the charging case and close the cap, they will power off automatically.

Note: Put either one earphone into the charging case, prompt sound 'Beep' will be produced, the another earphone will connect to device automatically with prompt sound 'Connected'.

Mode 2 Without Charging Case

1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both earphones

Single Mode

Charging

Earphones Charging Status

Open and close the charging case cap, wait for 3 seconds
The top LED light on: Right earphone is charging
The bottom LED light on: Left earphone is charging
When the earphone is fully charged, LED light will turn Off

Note: It takes about 1.5 hours to fully charge the earphones

Charging Case Charging Status

Open and close the charging case cap
Lights on charging case stand for the remaining battery capacity

Note: It takes about 1.5-2 hours to fully charge the charging case

1/4 Battery Left
2/4 Battery Left
3/4 Battery Left
Fully charged

Note

Please follow below steps when both earphones fail to pair with each other or occur connection related issues

1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power Off both earphones
3. Touch and hold the power button of Left earphone for 8 seconds with Blue and White lights flash 3 times
4. Touch and hold the power button of Right earphone for 8 seconds with Blue and White lights flash 3 times
5. Put the earphones back to the charging case
6. Delete all 'T1' related Bluetooth names from your phone
7. Turn on Bluetooth and reconnect the earphones
   

Note: Do not touch and hold the power button of both earphones at the same time, please do it on sequential order

Q & A

Q: Why the music cue in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven/Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption. Note: Please keep your phone and the master earphone (R) as close as possible to ensure a more stable Bluetooth connection.

Q: What should I do if the earphones stop charging?
A: We recommend you to charge the earphones by using our cable. If our cable do not work, please try to use another charging cable or power source to charge the earphones,

Q: How to contact ENACFIRE Customer Service Team?
A: If you have any issue with the product, please contact us via:
support@enacfireglobal.com (US/ CA) /
moongu@enacfireglobal.com (UK).
We will reply to you within 24 hours and 100% solve your issue.

Safety Instruction

using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety. Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.
DO not use earphones in thunderstorm weather, the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning,
Earphones may not work properly under high temperature or high humidity conditions.
DO not use any corrosive cleaner/oil to clean the earphones If the earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried,

Tips: Man-made damage and lost are not covered under warranty. Keep the earphones and the packaging out of reach of children.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ENACFIRE T1 - Wireless Earbuds Manual