Table of Contents
Advertisement
Cooking assist functions
en
Height
0 - 100 m.
100 - 200 m.
200 - 400 m.
400 - 600 m.
600 - 800 m.
800 - 1000 m.
1000 - 1200 m.
1200 - 1400 m.
Above 1400 m.
* Basic setting
Temperature setting 3/100 ºC is sufficient for
Note:
efficient boiling, even if the water does not boil very
strongly. However, the boiling point can be changed.
For example, you can set a lower altitude if you want the
water to boil more strongly.
Connecting the wireless temperature sensor to the
control panel
You will need to connect the wireless temperature
sensor to the control panel before using the cooking
functions for the first time.
To connect the wireless temperature sensor to the
control panel, follow the instructions below:
Select the
menu; see the section on ~ "Basic
™‚...
1.
settings"
The hotplate indicator will light up.
Select the hotplate and its indicator will light up. A
2.
signal will sound. The
Press the
å
symbol on the wireless temperature
3.
sensor within 30 seconds.
After a few seconds, the status of the connection
between the temperature sensor and the control
panel will appear on the hotplate's display.
Status
Connected correctly
‹
Not connected correctly: Transmission error.
‚
Not connected correctly: Temperature sensor fault.
ƒ
The cooking functions are made available once the
■
temperature sensor has been connected to the
control panel correctly.
If there is a fault with the temperature sensor, the
■
connection may not be established correctly for the
following reasons:
– Bluetooth communication error.
– You did not press the symbol on the temperature
sensor within 30 seconds of selecting a hotplate.
– The battery in the temperature sensor has run
out.
Reset the wireless temperature sensor and follow
the connection procedure once again.
If the temperature sensor and the control panel are
■
not connected correctly due to a transmission error,
follow the connection procedure once again.
If the display continues to show incorrect connection
, contact our technical after-sales service.
‚
26
Setting
™...
‚
ƒ
„
*
...
†
‡
ˆ
‰
Š
indicator will light up.
å
Resetting the wireless temperature sensor
Touch and hold the
1.
8-10 seconds.
While you are doing this, the temperature sensor's
LED indicator will light up three times. When the LED
lights up for the third time, it will start to reset the
temperature sensor. At this point, you will need to lift
your finger off the symbol.
Once the LED goes out, this means that the wireless
temperature sensor has been reset.
Repeat the connection procedure from point 2.
2.
Setting procedure
Attach the temperature sensor to the saucepan; see
1.
the section on ~ "Preparing and maintaining the
wireless temperature sensor"
Place a saucepan filled with sufficient liquid on the
2.
required hotplate and always put the lid on.
Select the hotplate on which you have placed the
3.
saucepan with the temperature sensor.
Touch the
symbol on the temperature sensor.
å
4.
The indicator
will light up in the control panel.
å
Select the right temperature setting from the table.
5.
The function has now been activated.
The temperature symbol
or oil has reached the right temperature for adding
the food. A signal will sound and the temperature
symbol will stop flashing.
Once the signal has sounded, take the lid off and
6.
add the food. Keep the lid on during cooking.
Do not cover the pan when using the "Frying
Note:
with a large amount of oil in the saucepan" function.
Switching off cooking functions
Select the hotplate and set it to
panel. The hotplate will switch off and the residual heat
indicator will appear.
To re-activate the cooking functions, wait for
Note:
approximately 10 seconds.
symbol for approximately
å
will flash until the water
å
.
on the control
‹
‹
Advertisement
Table of Contents
