Related Manuals for D&R ELECTRONICS F5M-IQ
Summary of Contents for D&R ELECTRONICS F5M-IQ
- Page 1 F5M-IQ INSTALLATION MANUAL Model F5M-IQ1 F5M-IQ2 IMPORTANT: Carefully read ALL instructions and warnings before attempting to install and operate this equipment. July 31, 2019...
-
Page 2: Table Of Contents
6—F5M-IQ DEFAULT CONFIGURATION……………………………………………… Page 7 7—F5M-IQ TOUCHPAD PROGRAMMING…………………………………………….. Page 8 8—F5M-IQ VOLTAGE CALIBRATION…………………………………………………. Page 8 9—F5M-IQ TEMPERATURE CALIBRATION………………………………………….. Page 9 10—F5M-IQ TOUCHPAD BACKLIGHT QUICK SETTING…………………………... Page 9 11—IMAGES……………………………………………………………………………….. Page 10 REAR VIEW CONNECTORS LAYOUT…………………………………………... Page 10 FRONT VIEW CONNECTORS LAYOUT…………………………………………. Page 11 TOP VIEW (FUSES AND LED INDICATORS)…………………………………... -
Page 3: 1-Unpacking & Pre-Installation Check
1. Unpacking & Pre-Installation Check D&R Electronics Co. recommends that you open and examine all shipments within 48 hours of receipt. The INTIMIDATOR IQ systems are shipped pre-assembled and factory tested. All necessary hardware for standard installation is included. Use this pre-installation check list to verify your unit: 1.Confirm contents with the packing slip 2.Examine unit for damaged in transit (i.e. -
Page 4: 3-Specifications
3. Specifications General Input Voltage ............11 to 16 Volts DC Input Fuse ..............60 Amps (external) Operating Temperature Ranges ......-40 C to +65 Standby Current ............50mA + 10% during IGNITION OFF time-out ….………………………..………….ØmA after time-out Control Box Weight Control Box Physical Dimensions Height .........2 - 1/16”... -
Page 5: 4-Installation
4. Installation CONNECTOR #1 PIN 1 — Connect a BLACK 10 AWG wire to battery GROUND. PIN 2 — Connect a RED 10 AWG wire to the POSITIVE side of the battery, using a 60A breaker. PIN 3 — Connect a RED 10 AWG wire to the POSITIVE side of the battery, using the same 60A breaker as PIN 2. -
Page 6: 5-Labeling Instructions
CONNECTOR #6 PIN 1 — SIREN #1 SPEAKER PIN 2 — SIREN #1 SPEAKER PIN 3 — SIREN #2 SPEAKER (optional) PIN 4 — SIREN #2 SPEAKER (optional) PIN 5 — HORN PIN 6 — HORN RING PIN 7 — RADIO input PIN 8 —... -
Page 7: 6-F5M-Iq Default Configuration
6. F5M-IQ DEFAULT TOUCHPAD CONFIGURATION The touchpad setup is a standard factory default. For setup changes refer to the software manual for program- ming. The labels can be rearranged as per customer’s preference. STBY/PA — Momentary AIR HORN (optional can be programmed to momentary WAIL). -
Page 8: 7-F5M-Iq Touchpad Programming
Press SW8 to save and exit programming 8. F5M-IQ VOLTAGE CALIBRATION The F5M-IQ system provides a continuous battery voltage reading on the touchpad’s display. After a set- up update, the display will show “Voltage 0V” even though the voltage input is connected to the battery. -
Page 9: 9-F5M-Iq Temperature Calibration
9. F5M-IQ TEMPERATURE CALIBRATION (optional equipment) The F5M-IQ system provides an optional connection for up to 3 temperature sensor modules. To calibrate the temperature follow these steps: Step 1: Using a thermometer, record the temperature were the temperature sensor is installed. -
Page 10: 11-Images
11. IMAGES IQ-CONTROL BOX REAR VIEW Figure 1: Input / Output Layout July 31, 2019... -
Page 11: Front View Connectors Layout
IQ-CONTROL BOX FRONT VIEW CONNECTOR #11: DATA Figure 2 IQ-CONTROL BOX TOP VIEW Figure 3: IQ-Control Box Output LED Indicators And Output fuses 12. TOUCHPAD FILE UPLOAD ERROR CODES Error Name Error Description LCD Display FIELD_COUNT TPP file fields counts is wrong, file content is wrong Error 1 INVALID_VERSION TPP file version is wrong... -
Page 12: 13-Warranty & Product Return Policy
WARRANTY D & R Electronics warrants its new products to be free from defects in material and workman- ship, under normal use and service for a period of three years on parts replacement. This warranty applies only to original purchasers acquiring the product directly from D&R Electronics, or its authorized dealers.