Related Manuals for D&R ELECTRONICS RDS17S-ELITE1-R1
Summary of Contents for D&R ELECTRONICS RDS17S-ELITE1-R1
- Page 1 RDS17S-ELITE-R1 INSTALLATION MANUAL Model RDS17S-ELITE1-R1 RDS17S-ELITE2-R1 IMPORTANT: Carefully read ALL instructions and warnings before attempting to install and operate this equipment. Jan 15, 2020...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1—UNPACKING & PRE-INSTALLATION CHECK…………………………………. Page 3 2—SAFETY CONSIDERATIONS……………………………………………………... Page 3 3—SPECIFICATIONS…………………………………………………………………... Page 4 4—INSTALLATION……………………………………………………………………… Page 5 5—LABELING INSTRUCTIONS……………………………………………………….. Page 6 6—RDS17S-ELITE-R1 DEFAULT CONFIGURATION…………………………..….. Page 7 7—RDS17S-ELITE-R1 TOUCHPAD BACKLIGHT QUICK SETTING…………..… Page 8 8—IMAGES………………………………………………………………………………. Page 9 REAR VIEW CONNECTORS LAYOUT………………………………………… Page 9 FRONT VIEW CONNECTORS LAYOUT………………………………………. -
Page 3: 1-Unpacking & Pre-Installation Check
1. Unpacking & Pre-Installation Check D&R Electronics Co. recommends that you open and examine all shipments within 48 hours of receipt. The INTIMIDATOR IQ systems are shipped pre-assembled and factory tested. All necessary hardware for standard installation is included. Use this pre-installation check list to verify your unit: 1.Confirm contents with the packing slip 2.Examine unit for damaged in transit (i.e. -
Page 4: 3-Specifications
3. Specifications General Input Voltage ............11 to 16 Volts DC Input Fuse ..............60 Amps (external) Operating Temperature Ranges ......-40 C to +65 Standby Current ............50mA + 10% during IGNITION OFF time-out ….………………………..………….ØmA after time-out Control Box Weight Control Box Physical Dimensions Height .........2 - 1/16”... -
Page 5: 4-Installation
4. Installation CONNECTOR #1 PIN 1 — Connect a BLACK 10 AWG wire to battery GROUND. PIN 2 — Connect a RED 10 AWG wire to the POSITIVE side of the battery, using a 60A breaker. PIN 3 — Connect a RED 10 AWG wire to the POSITIVE side of the battery, using the same 60A breaker as PIN 2. -
Page 6: 5-Labeling Instructions
CONNECTOR #6 PIN 1 — SIREN #1 SPEAKER PIN 2 — SIREN #1 SPEAKER PIN 3 — SIREN #2 SPEAKER (optional) PIN 4 — SIREN #2 SPEAKER (optional) PIN 5 — HORN PIN 6 — HORN RING PIN 7 — RADIO input PIN 8 —... -
Page 7: 6-Rds17S-Elite-R1 Default Configuration
6. RDS17S-ELITE-R1 DEFAULT TOUCHPAD CONFIGURATION The touchpad setup is a standard factory default. For setup changes refer to the software manual for program- ming. The labels can be rearranged as per customer’s preference. SLIDE SWITCH 1 — Activates STBY, Output 1 continuous ON and the rear of the lightbar. SLIDE SWITCH 2—... -
Page 8: 7-Rds17S-Elite-R1 Touchpad Backlight Quick Setting
7. RDS17S-ELITE-R1 TOUCHPAD BACKLIGHT QUICK SETTING The RDS17S-ELITE-R1 system provides a 6 level quick adjustment for the touchpad backlight. To make a quick adjustment of the touchpad backlight follow these steps: Step 1: Press and hold down SW1. Step 2: After 3 seconds the backlight quick adjustment is enabled. -
Page 9: 8-Images
8. IMAGES IQ-CONTROL BOX REAR VIEW Figure 1: Input / Output Layout Jan 15, 2020... -
Page 10: Front View Connectors Layout
IQ-CONTROL BOX FRONT VIEW CONNECTOR #10 CONNECTOR # 12 CONNECTOR #11 Figure 2 IQ-CONTROL BOX TOP VIEW Figure 3: IQ-Control Box Output LED Indicators And Output fuses Jan 15, 2020... -
Page 11: 9-Touchpad Setup File Upload Error Codes
9. TOUCHPAD FILE UPLOAD ERROR CODES Error Name Error Description TP BUTTON LED __●○○○○○ 1 FIELD_COUNT TPP file fields counts is wrong, file content is wrong ○○○○○○○○ __○●○○○○ 2 INVALID_VERSION TPP file version is wrong ○○○○○○○○ __●●○○○○ 3 WRONG_TOUCHPAD TPP file is defined wrong TouchPad type ○○○○○○○○... -
Page 12: 10-Warranty & Product Return Policy
WARRANTY D & R Electronics warrants its new products to be free from defects in material and workman- ship, under normal use and service for a period of three years on parts replacement. This warranty applies only to original purchasers acquiring the product directly from D&R Electronics, or its authorized dealers.