Cleaning And Maintenance; Troubleshooting; Manufacturer's Warranty - STEINEL L 605 LED Information

Programme 4
NM Nightmatic programme
– Soft light start.
– No night light.
– No movement evaluation
Light is switched to 100% output when
ambient light level falls below brightness
response threshold.
Manual override (Fig. 5.2)
In manual override mode, the light stays
ON for 4 hours. Then it returns to sensor
mode. Manual override mode is activat­
ed at the mains power switch (pressing
within 0.2 to 1.0 second).
• Activate: 2 × OFF and 2 × ON.
• Deactivate: 1 × OFF and 1 × ON.
Adjusting the detection zone
To rule out inadvertent triggering or target
specific danger spots, the detection zone
can be limited with film shrouds. The film
shroud is stuck onto the sensor unit.
– Limit the detection zone's max. reach
with the top film shroud. (Fig. 5.3)
– Limit the horizontal detection zone
with film­shroud segments cut to
size. (Fig. 5.4/5.5)
6. Cleaning and
Maintenance
Hazard from
electrical power.
Contact between water and live parts can
result in electrical shock, burns or death.
• Light must not be wet­cleaned.
Risk of damage to property!
Using the wrong detergent can damage
the light.
• Make sure detergent does not harm
the surface.
• Clean light with a soft cloth and mild
detergent.

7. Troubleshooting

Light does not switch ON.
– Fuse not switched ON or faulty.
• Switch ON fuse.
• Change faulty fuse.
– Break in wiring.
• Check wiring with voltage tester.
– Short circuit in mains power supply
lead.
• Check connections.
– Mains switch OFF.
• Switch ON mains switch.
– Wrong twilight setting selected.
• Re­set brightness response
threshold
– Light source faulty.
• The light source cannot be
changed. Completely replace light.
Light does not switch OFF.
– Continued movement within the
detection zone.
• Check detection zone.
• If necessary, limit detection zone.
– Night light selected.
• Select programme without night
light.
Light switches ON without any
identifiable movement.
– Install light at a non­vibrating site.
• Securely mount enclosure.
– Movement occurring, but is not iden­
tified by the observer (e.g. movement
behind wall, movement of a small
object in immediate light vicinity.)
• Check detection zone.
16
8. Disposal
Electrical and electronic equipment,
accessories and packaging must be re­
cycled in an environmentally compatible
manner.
Do not dispose of electrical
and electronic equipment as
domestic waste.
G B
EU countries only:
Under the current European Directive on
1
Waste Electrical and Electronic Equip­
Y E A R
ment and its implementation in national
MANUFACTURER'S
law, electrical and electronic equipment
WARRANTY
no longer suitable for use must be
collected separately and recycled in an
environmentally compatible manner.
9. Manufacturer's
Warranty
This Steinel product has been manufac­
tured with utmost care, tested for proper
operation and safety and then subjected
to random sample inspection. Steinel
guarantees that it is in perfect condition
and proper working order. The warranty
period is 36 months and starts on he date
of sale to the consumer. We will remedy
defects caused by material flaws or
manufacturing faults. The warranty will be
met by repair or replacement of defective
parts at our own discretion. The warranty
shall not cover damage to wear parts,
damage or defects caused by improper
treatment or maintenance. Further conse­
quential damage to other objects shall be
excluded.
Claims under the warranty will only be
accepted if the unit is sent fully assembled
and well­packed with a brief description
of the fault, a receipt or invoice ( date
of purchase and dealer's stamp ) to the
appropriate Service Centre.
Repair service:
If defects occur outside the warranty
period or are not covered by the warranty,
ask your nearest service station for the
possibility of repair.
5
3
Y E A R Y E A R
MANUFACTURER'S MANUFACTURER'S
WARRANTY WARRANTY
17