Quick Reference - Supermicro X7DA3 User Manual

Quick Reference (X7DA3)
Jumper Description
J3P 3rd PWR Failure Detect
JAR Alarm Reset
JBT1 CMOS Clear
JCF1 Compact Card Master/Slave Select
2 2
JI C1/JI C2 SMB to PCI-X Slots
2 2
JI C3/JI C4 SMB to PCI-E Slots
JPS1 SAS Controller Enable
JPAC Audio Enable
JPL1/ JPL2 GLAN1/GLAN2 Enable
JWD Watch Dog
Connector
ATX PWR (JPW1)
Aux. PWR/CPU PWR
Audio (JC1/JC2)
COM1/COM2 (JCOM1/2) COM1/COM2 Serial Port Connectors
Compact PWR (JWF1)
DIMM#1A-DIMM#4B
FAN 1-8
Floppy (J22)
FP Control (JF1)
GLAN 1/2 (JLAN1)
IDE1/IDE2(*Note 1 Below)IDE1 Hard Drive (JIDE1)/Compact Flash Card (JIDE2)
JL1
LE1(*Note 2 Below)
OH LED (JOH1)
Parallel (J21)
PWR LED/SPKR (JD1)
PWR SMB (J17)
PSF
SAS#0-#3,#4-#7(JSM1/2) SAS (Serial Attached SCSI) Connectors #0-#3, #4-#7
SATA#0-#5(JS1-JS6)
SGPIO 1/2(J29,J30)
SMB (J18)
Slot 7
USB 0/1/2/3/4/5 (JUSB1) Back Panel USB 0/1/2/3(JUSB1)
USB 4/5 (JUSB2)
WOL (JWOL)
WOR (JWOR)
Notes: 1.JIDE2 is for Compact Card Use only. JCF1 is used to confi gure the
compact fl ash card as a master or a slave drive. Be sure to connect JWF1 to a
power supply to provide power to the compact fl ash card. 2. When LE1 is on, the
Standby Power is on. Unplug the PWR cables before changing components.
Description
Primary 24-Pin ATX PWR Connector
+12V 4-pin PWR (JWP2)/+12V 8-pin PWR(JPW3)
Audio Microphone (JC1), Line-In/Line-Out (JC2)
Compact Card PWR Connector
Memory DDRII Fully Buffered DIMM Slots
Fans 1-8 (Fan7: CPU Fan1, Fan8: CPU Fan2)
Floppy Disk Drive Connector
Front Control Panel Connector
G-bit Ethernet Ports
Chassis Intrusion Header
5V Standby PWR LED Indicator
Overheat LED
Parallel (Printer) Port
PWR LED(pins1-3)/SpeakerHeader (pins 4-7)
Power System Management (I
Power Supply Failure (See Chapter 2)
Serial ATA Connectors #0-5
Serial General Purpose Input/Output Headers
System Management Bus Header
SIM Low Profi le IPMI Connector
Front Panel USB4/5 (JUSB2)
Wake-on-LAN Header
Wake-on-Ring Header
1-5
Chapter 1: Introduction
Default Setting
Off (Disabled)
Off (Disabled)
See Chapter 2
On (Master)
Pins 2-3 (Disabled)
Pins 2-3 (Disabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
2
C) Header