Page 1 1000Sport CF1000US CF1000US-A CF1000UTR-B OWNER’S MANUAL READ THIS MANUAL CAREFULLY It contains important safety information Make sure operator holds a valid driver license. Passenger under 12 are prohibited.
Page 2: Table Of Contents
TABLE OF CONTENTS Foreword �� 7 Welcome �� 7 Catalytic Converter �� 8 Signal Words �� 9 Introduction �� 12 Vehicle Identification Numbers and Key Information �� 13 ZFORCE 1000 Specifications �� 14 Operator Safety �� 21 General Safety Precautions �� 21 Owner Responsibilities ��...
Page 3 Dashboard Indicators and Warnings �� 82 Indicators and Warnings �� 83 Operating Your Vehicle �� 89 Break-In Period �� 89 Recommended Engine Oil Viscosity �� 90 Pre-Ride Inspection �� 91 Pre-Ride Inspection Check List �� 91 Throttle �� 95 Foot Brake �� 95 Starting the Engine ��...
Page 4 Break-In Maintenance Checklist �� 133 Periodic Maintenance Schedule �� 135 Inspection and Service Record �� 142 Maintenance Procedures�� 144 Air Filter �� 144 Inspect The Engine Oil Level �� 147 Engine Valve Clearance Adjustment �� 152 Engine Idle Speed �� 152 Front and Rear Gear Case ��...
Page 5 Perform Repairs �� 187 Check the Tires �� 187 Oil and Filter �� 187 Air Filter/ Air Box �� 187 Check Fluid Levels �� 188 Stabilize the Fuel �� 188 Battery Storage �� 188 Lubricate �� 188 ‘Fog’ the Engine �� 189 Transporting the Vehicle ��...
Page 6 Declaration �� 199 Declaration of Drivers exposure to noise level �� 199 Declaration of Vibration declaration �� 200 CFMOTO LIMITED WARRANTY �� 201 Change of Ownership �� 206...
Page 7: Foreword
Foreword Welcome Thank you for purchasing a CFMOTO vehicle, and welcome to our world-wide family of CFMOTO enthusiasts. Be sure to visit us at www.cfmoto.com for the latest news, new product introductions, upcoming events, career opportunities, and more. CFMOTO develops, manufactures, markets and delivers the world’s most reliable and cost effective all terrain vehicles, motorcycles and scooters, utility vehicles, boat and power sports engines.
Page 8: Catalytic Converter
Foreword WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Catalytic Converter CAUTION-Please respect the following instructions to protect your catalytic converter: • Use only unleaded gasoline. Even if the gasoline contains a little lead, it could damage the reactive metals contained in the catalytic converter and disable it.
Page 9: Signal Words
Foreword Signal Words A signal word calls attention to a safety message or messages, a property damage message or messages, and designates a degree or level of hazard seriousness. The standard signal words in this manual are WARNING, CAUTION and NOTE or NOTICE. The following signal words and symbols appear throughout this manual and on your vehicle.
Page 10 Foreword WARNING Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels. Failure to follow the safety precautions could result in serious injury or death. WARNING Improper operation of this vehicle could result in serious injury or death. NEVER: •...
Page 11 Foreword ALWAYS USE AN APPROVED, SUITABLE HELMET AND PROTECTIVE GEAR FOR OPERATOR AND PASSENGER. NEVER USE DRUG OR ALCOHOL BEFORE OR WHEN RIDING.
Page 12: Introduction
Introduction Welcome to the worldwide family of CFMOTO owners. We proudly produce exciting powersports products such as sports vehicles, utility vehicles, and recreational vehicles. • All-Terrain Vehicles ( A TV ) • Utility ( U TV ) and sport Side-by-Side ( S SV ) Vehicles •...
Page 13: Vehicle Identification Numbers And Key Information
Introduction Vehicle Identification Numbers and Key Information Record your vehicle’s identification numbers in the spaces provided. Remove the spare key and store in a safe place. Your key can be duplicated only by mating a key blank with one of your existing keys. If both keys are lost, the complete lock assembly must be replaced.
Page 14: Zforce 1000 Specifications
Specifications ZFORCE 1000 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Overall Length 129.4in. ( 3 185mm ) 118.9in. ( 3 020mm ) 117.7in. ( 2 990mm ) 71.7in. ( 1 820mm ) Overall Width 65in. ( 1 650mm ) 61.6in.
Page 15 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Bore × Stroke 3.5 in. × 2.91 in. ( 9 1 mm × 74 mm ) × 2 Displacement 962.6 mL Compression Ratio 10�6 : 1 Starting Type Electric start Lubrication Type Pressure / Splash lubrication Engine Coolant: Type...
Page 16 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Rear gear case Oil: Type SAE 80W-90 GL-5 Volume: 13.5 oz. ( 4 00 mL ) Periodic Oil Change Front gear case Oil: Type SAE 80W-90 GL-5 Volume 11.1 oz. ( 3 30 mL ) Periodic Oil Change Air Filter Paper type...
Page 17 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Spark Plug Type DCPR8E ( N GK ) Spark Plug Gap 0.031in ~ 0.035in. ( 0 .8mm ~ 0.9mm ) Transmission CVT + Gearbox Gear Shift/Order Manual / L—H—N—R—P CVT Ratio 0�70 ~ 2�88 Transmission Low Gear 43/17 = 2�529...
Page 18 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Tire Pressure: Front Load ≤ 195kg: 14.5 PSI ( 1 00 kPa ) Load > 195kg: 16 PSI ( 1 10 kPa ) Rear Load ≤ 195kg: 16 PSI ( 1 10 kPa ) Load >...
Page 19 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Shock Absorber: Front Shock Absorber Gas shock Rear Shock Absorber Gas shock Wheel Travel: Front Wheel Travel 11 in. ( 2 80 mm ) Rear Wheel Travel 11.8 in. ( 3 00mm ) Electrical System: Ignition Electronic...
Page 20 Specifications ZFORCE 1000 SPORT Item CF1000UTR-B CF1000US CF1000US-A Light System: Head Lamp, Low Beam LED 7W × 2 Head Lamp, High Beam LED 7W × 4 Front Position Light Tail Light/Brake Light LED 0.2W × 20 / 0.5W × 3 Dashboard LED and LCD -- Non-repairable ECU - 5A...
Page 21: Operator Safety
Operator Safety General Safety Precautions WARNING Failure to heed the warnings contained in this manual can result in serious injury or death� This vehicle is not a toy and can be hazardous to operate. This vehicle handles differently from other vehicles, such as cars. A collision or rollover can occur quickly, even during routine maneuvers like turning or driving over obstacles, if you fail to take proper precautions.
Page 22 Operator Safety Equipment Modifications CFMOTO is concerned with the safety of our customers and for the general public. Therefore, we strongly recommend that consumers do not install on a vehicle, any equipment that may increase the speed or power of the vehicle, or make any other modifications to the vehicle for these purposes. Any modifications to the original equipment of the vehicle create a substantial safety hazard and increase the risk of body injury.
Page 23 Operator Safety Avoid Gasoline Fires and Other Hazards Gasoline is extremely flammable and highly explosive. Fuel vapors can spread and be ignited by a spark or flame many feet away from the engine. To reduce the risk of fire or explosion, follow these instructions: •...
Page 24 Operator Safety WARNING Gasoline is highly flammable and explosive under certain conditions. Allow the engine and exhaust system to cool before filling the tank. Always exercise extreme caution whenever handling gasoline. Always refuel with the engine stopped, and outdoors or in a well ventilated area. Never carry a plastic container with gasoline in the cargo area while riding.
Page 25: Owner Responsibilities
Operator Safety Owner Responsibilities Be Qualified and Responsible Read this Owner’s Manual and the warning decals on this vehicle carefully. Take a safety training course on open areas if available. Practice at low speeds. Higher speeds require greater experience, knowledge and suitable riding conditions.
Page 26 Operator Safety Riding Carefully • This vehicle is not a toy and can be hazardous to operate. This vehicle handles differently from other vehicles such as motorcycles or cars. A collision or rollover can occur quickly, during abrupt maneuvers such as sharp turns, acceleration or deceleration, and driving on hills or over obstacles if you fail to take proper precautions�...
Page 27 Operator Safety Roll Over Protection System ( R OPS ) • The ROPS on this vehicle meets the performance requirements of ISO 3471:2008. The ROPS can limit intrusions of outside objects and reduce your risk of injury in rollovers. • Always follow all safe operating practices outlined in this manual to avoid vehicle rollover.
Page 28 Operator Safety • Always follow proper procedures for climbing or going down hills. Never go over the top of any hill at high speed� • Never attempt steep hills or side hilling when pulling a trailer. • Always check for obstacles before operating in a new area. Always follow proper procedures when operating over obstacles or fallen trees.
Page 29: Safe Riding Gear
Safe Riding Gear Always wear clothing suited to the type of riding. Operating this vehicle requires wearing special protective clothing for comfort and to reduce the chance of injury: 1� A helmet is the most important piece of protective gear for safe riding�...
Page 30: Safety Labels, Locations And Warnings
Operator Safety Safety Labels, Locations and Warnings Warning labels have been placed on the vehicle for your protection. Read and follow the instructions on each decal carefully. If a decal becomes illegible or comes off, contact your dealer to purchase a replacement. Read and follow the safety warnings in this manual.
Page 31 Operator Safety Safety Labels...
Page 32 Operator Safety Safety Labels 5BYB-190003 EU19C...
Page 33 Operator Safety Safety Labels...
Page 34 Operator Safety Safety Labels...
Page 35: Safety Labels, Locations And Warnings
Operator Safety Safety Labels, Locations and Warnings Warning labels have been placed on the vehicle for your protection. Read and follow the instructions on each decal carefully. If a decal becomes illegible or comes off, contact your dealer to purchase a replacement. Read and follow the safety warnings in this manual.
Page 36 Operator Safety Safety Labels...
Page 37 Operator Safety Safety Labels 5BYB-190003 EU19C...
Page 38 Operator Safety Safety Labels...
Page 39 Operator Safety Safety Labels...
Page 40 Operator Safety Potential Hazard Warnings WARNING POTENTIAL HAZARD: Operating this vehicle without proper instruction� WHAT CAN HAPPEN: The risk of an accident is greatly increased if the operator does not know how to operate the vehicle properly in different situations and on different types of terrain. HOW TO AVOID THE HAZARD: Beginning and inexperienced operators should complete a safety training course if offered by dealer.
Page 41 Operator Safety WARNING POTENTIAL HAZARD: Carrying more passengers than the rated capacity� WHAT CAN HAPPEN: A passenger not seated in the vehicle could be ejected from the vehicle unexpectedly or make contact with moving components, both of which can result in severe injury or death. HOW TO AVOID THE HAZARD: Never allow carrying more than one passengers.
Page 42 Operator Safety WARNING POTENTIAL HAZARD: Operating this vehicle without wearing approved helmet, eye protection, and protective clothing. WHAT CAN HAPPEN: Operating without an approved helmet increases the risk of a severe head injury or death in the event of an accident.
Page 43 Operator Safety WARNING POTENTIAL HAZARD: Operating at excessive speeds. WHAT CAN HAPPEN: Excessive speed increases the operator’s chance of losing control, which can result in an accident. HOW TO AVOID THE HAZARD: Always operate at a speed that’s proper for the terrain, visibility and operating conditions, and your experience.
Page 44 Operator Safety WARNING POTENTIAL HAZARD: Failure to inspect the vehicle before operating. Failure to properly maintain the vehicle. WHAT CAN HAPPEN: Poor maintenance increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD: Always inspect your vehicle before each use to make sure it’s in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual.
Page 45 Operator Safety WARNING POTENTIAL HAZARD: Failure to use extra caution when operating on unfamiliar terrain. WHAT CAN HAPPEN: Unfamiliar terrain may contain hidden rocks, bumps, or holes that could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Travel slowly and use extra caution when operating on unfamiliar terrain.
Page 46 Operator Safety WARNING POTENTIAL HAZARD: Failure to use extra caution when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN: Operating on excessively rough, slippery or loose terrain could cause loss of traction or loss of control, which could result in an accident or overturn�...
Page 47 Operator Safety WARNING POTENTIAL HAZARD: Traveling down excessively steep hills. WHAT CAN HAPPEN: Improper downhill travel could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Never operate on hills too steep for the vehicle or for your abilities. Practice on smaller hills before attempting large hills.
Page 48 Operator Safety WARNING POTENTIAL HAZARD: Traveling down excessively steep hills. WHAT CAN HAPPEN: Improper downhill travel could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Never operate on hills too steep for the vehicle or for your abilities. Practice on smaller hills before attempting large hills.
Page 49 Operator Safety WARNING POTENTIAL HAZARD: Improperly crossing hills and turning on hills� WHAT CAN HAPPEN: Improperly crossing or turning on hills could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Use extra caution when turning on any hill. Avoid crossing the side of a steep hill. WHEN CROSSING THE SIDE OF A HILL: Always follow proper procedures as described in the owner's manual.
Page 50 Operator Safety WARNING POTENTIAL HAZARD: Stalling, rolling backwards while climbing a hill. WHAT CAN HAPPEN: The vehicle could overturn� HOW TO AVOID THE HAZARD: Maintain a steady speed when climbing a hill. IF ALL FORWARD SPEED IS LOST: Close the throttle. Apply the brake. When fully stopped, shift the gear selector to the park position. IF THE VEHICLE BEGINS ROLLING: Never apply engine power.
Page 51 Operator Safety WARNING POTENTIAL HAZARD: Improperly operating over obstacles. WHAT CAN HAPPEN: Operating over obstacles could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Before operating in a new area, check for obstacles. Avoid operating over large obstacles such as rocks and fallen trees when possible.
Page 52 Operator Safety WARNING POTENTIAL HAZARD: Overloading the vehicle or carrying/towing cargo improperly� WHAT CAN HAPPEN: Overloading and towing can cause changes in vehicle handling, which could lead to loss of control or an accident� HOW TO AVOID THE HAZARD: Never exceed the stated load capacity for this vehicle. Cargo should be properly distributed and securely attached.
Page 53 Operator Safety WARNING POTENTIAL HAZARD: Operation the vehicle through deep or fast-flowing water. WHAT CAN HAPPEN: Tires may float, causing loss of traction and loss of control, which can lead to an accident or overturn. HOW TO AVOID THE HAZARD: Avoid operating through deep or fast-flowing water.
Page 54 Operator Safety WARNING POTENTIAL HAZARD: Improperly operating in reverse� WHAT CAN HAPPEN: The vehicle could collide with an obstacle or person, resulting in severe injury. HOW TO AVOID THE HAZARD: Before shifting into reverse gear, always check for obstacles or people behind the vehicle. When it's safe to proceed, back slowly.
Page 55 Operator Safety WARNING POTENTIAL HAZARD: Operating the vehicle with improper modifications. WHAT CAN HAPPEN: Improper installation of accessories or modification of the vehicle may cause changes in handling which could lead to an accident� HOW TO AVOID THE HAZARD: Never modify the vehicle through improper installation or use of accessories. All parts and accessories added to the vehicle must be genuine parts or equivalent components designed for use on this vehicle, and they should be installed and used according to approved instructions.
Page 56 Operator Safety WARNING Leaving the keys in the ignition can lead to unauthorized use of the vehicle, resulting in serious injury or death� Always remove the ignition key when the vehicle is not in use� WARNING After any overturn or accident, have an authorized dealer inspect the entire vehicle for possible damage, including ( ...
Page 57 Controls and Features...
Page 58: Occupants Protector
Controls and Features Occupants Protector Cab Frame - ( 1 ) This vehicle is equipped with cab frame. It helps to protect the occupants from injury in case of a rollover or other dangerous situation� Side Door - ( 2 ) This vehicle is equipped with two side doors that help to keep arms, legs and shoulders inside the vehicle to prevent possible injury�...
Page 59 Controls and Features...
Page 60: Hitch And Winch
Controls and Features Hitch and Winch Hitch - ( 6 ) This vehicle is equipped with a standard size of hitch receiver by 2 in. × 2 in. ( 5 1 mm × 51 mm ) . Please consult with your dealer about hitch use and how to use a trailer before operating the vehicle.
Page 61 Controls and Features Winch - (8 ) (If equipped) This vehicle is equipped with a winch, attached with a remote controller and a standard winch controller that is located inside of front storage box. Only operate the winch when engine is running to keep the battery capacity.
Page 62 Controls and Features GENERAL SAFETY PRECAUTIONS REGARDING THE USE OF WINCH Prior to initiating winching operation be sure any element which  Moving Part Hazards can interfere with safe winching is removed. To prevent serious injury and property damage: Do not disengage clutch if winch is under load or wire rope is in  Do not operate or install winch without reading and tension.  understanding these instructions and the Basic Guide to Take your time. Sloppy rigging causes accidents.  Winching Techniques. The wire rope must always spool onto the drum as indicated by  Keep hands clear of wire rope, hook and fairlead opening during the drum rotation label on the winch. ...
Page 63 Controls and Features Rear Access Cover - ( 9 ) Removal: Grasp the cover edge, pull upward to release the grommet pins, and remove. Install: Insert the cover tabs into the corresponding holes on the body, then align the grommet pins and press down. NOTE: Maintain easy removal cover by applying thin lubricant to the grommet pins occasionally�...
Page 64 Controls and Features Air Filter Access Cover - ( 1 0) Remove the mushroom head screw ( 1 ) and take off the clasp ( 2 ) , to remove the air filter access cover. The air filter cover can be removed, and the air filter can serviced.
Page 65 Controls and Features Front Access Cover - ( 1 2 ) Remove front access cover, then inspection and maintenance is required for the radiator assy, reservoir tank, brake fluid reservoir, battery and relay box. Removal: Grasp the cover edge, pull upward to release the grommet pins, and remove.
Page 66 Controls and Features...
Page 67: Primary Controls
Controls and Features Primary Controls Tilt Lever and Steering Wheel Lock - ( 1 4 ) 14.1: The steering wheel can be locked, turn the key for 180º by 14�1 counter clockwise to lock steering wheel. And turn the key for 180º by clockwise to release the lock of steering wheel.
Page 68 Controls and Features Electronic Throttle Pedal - ( 1 6 ) The Electronic throttle pedal is located to the right of the brake pedal. The throttle pedal controls engine rpm and vehicle speed. To control vehicle speed, press on the throttle pedal with your right foot. Always check the pedal function before driving.
Page 69 Controls and Features Brake Pedal - ( 1 7 ) The brake pedal is located at the left side of throttle pedal. Release throttle pedal and apply brake pedal to reduce speed or stop the vehicle� Hand Brake - ( 1 8 ) This vehicle is equipped with an auxiliary hand brake, which is located to the rear of the gear shifter.
Page 70 Controls and Features Gear Shift Lever - ( 1 9 ) The gear shift lever is located at the right side of driver seat. Use for changing the transmission gear selection: Apply brake pedal before shifting gear, to ensure personnel safety. L –...
Page 71 Controls and Features NOTE: In reverse operation, the engine’s RPM is limited, thus limiting the vehicle reverse speed under 15.5 mph ( 2 5 km/h ) . WARNING Use extreme caution driving downhill in reverse. Gravity can increase the vehicle speed above the set limited reverse speed�...
Page 72: Secondary Controls
Controls and Features Secondary Controls Switch Panel - ( 2 0 ) Main Light Switch The main light switch consists of 3 positions. Turn the switch to select the following functions: When the switch is on this position, head light, position light, tail light and instrument light are ‘on’.
Page 73 Controls and Features Dimmer Switch Dimmer switch consists of two positions, apply the related switch according to following function selection: When the switch is on this position, high beam works. When the switch is on this position, low beam works. Horn Switch Press the switch to sound the horn.
Page 74 Controls and Features Override Switch The engine is normally speed limited when operating in 4WD LOCK. If conditions require more engine power: Release the throttle and press the override button, the override indicator light will be ‘on’. Continue to press the button, then reapply the throttle. The engine will have full power.
Page 75 Controls and Features Hazard Switch ( I f equipped-available only in select countries ) When the switch is on this position, front and rear turning light will flash. The hazard switch indicator light in the dashboard will be on. When the switch is on this position, front and rear turning ●...
Page 76 Controls and Features Stop Switch When the switch is on this position, ECU, fuel injector, ignition coil, fuel pump and starting system will stop working� When the switch is on this position, ECU, fuel injector, ignition coil, fuel pump and starting system will function. 2WD / 4WD Switch This vehicle is equipped with an on-command “2WD”/”4WD”...
Page 77 Controls and Features NOTE: 4WD-LOCK OPERATION: Steering will require greater effort in 4WD-LOCK mode. When the switch is set to “LOCK”, the front diff-lock indicator light will flash until the front differential is locked. If the indicator light is flashing, turning the steering left and right will help the front gear locking mechanism to engage�...
Page 78 Controls and Features...
Page 79: Other Functions
Controls and Features Other Functions Cargo Rack - ( 2 1 ) This vehicle is equipped with a cargo rack, which can storage a small mount of cargo, and allows for cargo to be secured with ties or straps. Fuel Filling Cap - ( 2 2) The fuel filling cap is located at the side of passenger seat, near the seat.
Page 80 Controls and Features Sport Mode AM 10:50 23 22 21 20 19...
Page 81 Controls and Features ECO Mode AM 10:50 AM 10:50...
Page 82: Dashboard Indicators And Warnings
Controls and Features Dashboard Indicators and Warnings SEL - mode select 1 Drive mode 7 Call indicator 13 Position light 19 EPS button Bluetooth ADJ - mode 2 Engine RPM 20 Override indicator 26 Dashboard brightness indicator adjust button 3 Speedometer 9 Turning light 15 Odometer 21 Engine hour 27 EFI fault indicator...
Page 83: Indicators And Warnings
Controls and Features Indicators and Warnings 1. Drive Mode Display the current drive mode, there are three modes, 2WD, 4WD and 4WD-LOCK. 2. Engine RPM Indicate the engine current RPM, keep the RPM away from the red area. 3. Speedometer Display the current vehicle speed.
Page 84 Controls and Features 7. Call Indicator After bluetooth pairing successfully, this indicator flashes when there is an incoming call, and it displays the telephone number. Short-press SEL to accept the call, short-press ADJ to finish the call. 8. Bluetooth Indicator This vehicle is equipped with bluetooth function.
Page 85 Controls and Features 11. Oil Pressure Indicator The oil pressure indicator is on when the oil pressure is very low. Please have your vehicle stopped safely at once when the indicator is on, and contact your dealer. 12. High Beam Indicator This indicator illuminates when the headlight switch turns to high beam position.
Page 86 Controls and Features 19. EPS Indicator The indicator will be on when a fault occurs in the Electronic Power Steering system. Please stop the vehicle and contact your dealer to eliminate the fault. 20. Override Indicator When pressing the override button, the indicator is on and 4WD-LOCK speed limitation will be released in this state�...
Page 87 Controls and Features 26. Dashboard Brightness Shift to be daylight state or night state automatically by inducing the current environment brightness. 27. EFI Fault Indicator This indicator displays when a fault occurs in the Electronic Fuel Injection system. Please stop the vehicle and contact your dealer to eliminate the fault.
Page 88 Controls and Features Dashboard Navigation / Settings / Adjustments Item State Display Operation Result Home interface TOTAL Short press Shift to trip TRIP Odometer Home interface TRIP Short press Shift to total Odometer Home interface TRIP Long press Trip resets to be zero TRIP Dashboard Shift to be dashboard...
Page 89: Operating Your Vehicle
Operating Your Vehicle Break-In Period The break-in period for a new engine is very important. Careful treatment of a new engine at the beginning of ownership will result in more efficient performance and longer life. Perform the following procedures carefully: 1�...
Page 90: Recommended Engine Oil Viscosity
Operating Your Vehicle CAUTION During the 20-hour break-in period: • Do not operate at sustained full throttle. Damage to engine parts or decrease engine life may result if excessive wide open throttle is used during the first 20 hours of use. •...
Page 91: Pre-Ride Inspection
Operating Your Vehicle Pre-Ride Inspection Before each use of the vehicle, a best practice is to check the vehicle according to the “Perform daily before operating the vehicle” checklist in the maintenance section of this manual. WARNING If a proper inspection is not done before each use, severe damage to the vehicle, severe injury, or death could result.
Page 92 Operating Your Vehicle ITEM INSPECTION PERFORM REMARKS Cargo Load: If you transport a cargo, respect the rear cargo box capacity of 220.5 Ib. (100 kg). Ensure cargo is properly secured to the rear cargo box. Vehicle Load: Ensure that total load on the vehicle (including operator, passenger, cargo and added cargo and load Cargo and load accessories) does not exceed rated load capacity.
Page 93 Operating Your Vehicle What to Do Before Starting the Engine (Key ON) ITEM INSPECTION PERFORM REMARKS Check operation of indicator lights in dashboard Dashboard Check for messages in dashboard. Check cleanliness of headlights, taillights, turn signals, position lights and reflectors. Lights and reflectors Check operation of headlights (high and low beams), brake lights, turn signals and position lights.
Page 94 Operating Your Vehicle What to Do After the Engine is Started ITEM INSPECTION PERFORM REMARKS Check if steering operates freely by completely turning it Steering from side to side. Turn the ignition switch to OFF to verify if engine will Ignition switch shut down�...
Page 95: Throttle
Operating Your Vehicle Throttle Before starting the engine, check the throttle pedal to be sure it is operating smoothly. Make sure it returns to the idle position as soon as the pedal is released. Regulate the speed of the vehicle by varying the throttle position.
Page 96: Shifting The Transmission
Operating Your Vehicle NOTE: Do not activate the starting system more than 10 seconds on each attempt. If the engine fails to start, release the start switch, pause a few seconds before the next attempt, then try the start switch again. Each attempt should be as short as possible to preserve battery energy.
Page 97 Operating Your Vehicle Shifting Out of Park 1� Verify the throttle is closed. 2� Apply the foot brake and press the gear selector button. 3� Shift to the desired gear by moving the gear selector along the shift guide. Shifting: Neutral to High Gear 1�...
Page 98 Operating Your Vehicle Shifting: Low Gear to High Gear 1� Verify the throttle is closed and the vehicle is stopped completely. 2� Apply the foot brake. 3� Shift to ‘H’ by moving the gear selector along the shift guide. Shifting: to Reverse Gear 1�...
Page 99 Operating Your Vehicle WARNING Before shifting into reverse, make sure there are no obstacles or people, and the area is safe behind you. When it is safe to proceed, go slowly. Avoid excessive throttle operation while in speed limit mode, as it may cause fuel to build in the exhaust, resulting in engine popping and/or engine damage.
Page 100: Responsibilities Of The Operator
Safe Operation - Driving Safely Responsibilities of the Operator As the operator of this vehicle, your common sense, judgment, and abilities are the only factors that will prevent injury to yourself, to others around you, and/or damage to the vehicle or environment. Recreational, Group, and Distance Riding One of the benefits of this vehicle is that it can take you off-road away from most communities.
Page 101 Safe Operation - Driving Safely Abrupt maneuvers or aggressive driving can cause rollovers or loss of control even in flat open areas. If the vehicle rolls over, any part of your body ( s uch as arms, legs, or head ) outside of the cockpit can be crushed and trapped by the cage or other parts of the vehicle.
Page 102 Safe Operation - Driving Safely • Sudden changes in terrain such as holes, depressions, banks, softer or harder ground or other irregularities may cause the vehicle to tip or become unstable. Observe the terrain ahead and slow down in areas of uneven terrain. This vehicle will handle differently when carrying or pulling a load: •...
Page 103: Practice Exercises
Safe Operation - Driving Safely Environment Off-road recreation is a privilege. Maintain your privilege by respecting the environment and the rights of others to enjoy it: • Chasing wildlife is illegal. Wildlife can die of exhaustion if chased by a motorized vehicle. •...
Page 104 Safe Operation - Driving Safely • Repeat the turning exercise, but this time maintain the throttle at the same level while turning. • Finally, repeat the turning exercise while accelerating slowly. • Practice exercises turning to the left. Note how your vehicle reacts in these different exercises. CFMOTO recommends releasing the throttle before entering a turn to help initiate directional change.
Page 105 Safe Operation - Driving Safely Remember, braking distance depends on vehicle speed, load and the type of surface. Also, the tires and brakes conditions play a major role. Reverse Exercise Practice using the reverse: • Place 1 cone marker on both sides of the vehicle beside each rear wheel. •...
Page 106: Operating Your Vehicle
Safe Operation - Driving Safely Operating Your Vehicle Off-Road Operation The very nature of off-road operation is dangerous. Any terrain which has not been specially prepared to carry vehicles presents an inherent danger where terrain substance, shape, and steepness are unpredictable.
Page 107 Safe Operation - Driving Safely WARNING When driving downhill in reverse, gravity can increase the vehicle speed above the set limited reverse speed. Failure to use caution when operating in reverse can result in serious injury or death. NOTE: This vehicle is equipped with a reverse speed limiter function. In reverse operation, the engine RPM is limited, thus limiting the vehicle reverse speed.
Page 108 Safe Operation - Driving Safely Beware of slippery surfaces such as rocks, grass, logs, etc., both in the water and on its banks. A loss of traction may occur. Do not attempt to enter the water at high speed. Water will affect the braking ability of your vehicle.
Page 109 Safe Operation - Driving Safely Riding on Gravel, Loose Stones, or Other Slippery Surfaces Riding on gravel or loose stones is very similar to riding on ice. They affect the steering of vehicle, possibly causing it to slide and tip over especially at high speeds. In addition, braking distance may be affected. Remember that “gunning”...
Page 110 Safe Operation - Driving Safely Uphill Driving Use the low gear ( L ) for uphill driving. Due to its configuration, this vehicle has very good traction even while climbing, so much so that tip-over is possible before traction is lost. For example, it is common to encounter terrain situations where the top of the hill has eroded to a point that the hill peak rises very sharply.
Page 111: Hauling And Towing Loads
Safe Operation - Driving Safely Hauling and Towing Loads Your vehicle can help you perform a number of different light tasks ranging from snow removal, to pulling wood, or carrying cargo. This can change the vehicle handling. To prevent possible injury, follow the instructions and warnings in this manual and on the vehicle�...
Page 112 Safe Operation - Driving Safely Vehicle Settings When Carrying Loads If the total load approaches maximum load capacity, including weight of operator, passenger, cargo, accessories and trailer Towing Hitch Weight: • Inflate the tires to maximum pressure: Front: 16 PSI ( 1 10 kPa ) , rear : 18 PSI ( 1 24 kPa ) . •...
Page 113 Safe Operation - Driving Safely WARNING Slack can cause a chain or cable to break and snap back, possibly causing injury. • When pulling a load, respect the maximum hauling capacity. • If pulling another vehicle, be sure that someone is controlling the pulled vehicle. They must brake and steer to prevent the vehicle from going out of control.
Page 114 Safe Operation - Driving Safely • Always use low gear while towing to avoid clutch wear and belt issues. • Reduce speed when hauling or towing loads� • Never exceed the stated load capacity for this vehicle. • All loads must be secured before operation. Unsecured loads may shift and create unstable operating conditions, which could result in loss of control of the vehicle.
Page 115 Safe Operation - Driving Safely • While towing, the vehicle should never exceed 10 mph ( 1 6 km/h ) towing a load on a level surface. Vehicle speed should never exceed 5 mph ( 8 km/h ) when towing loads in rough terrain, while cornering, or while ascending or descending a hill.
Page 116 Safe Operation - Driving Safely Where a designated attachment point is provided on the towbar Accessories and Modifications If no such attachment points are foreseen, the operator s manual shall prohibit the installation of a front-end loader� This T3 has not attachment points for front-end loader. Do not install front loader.
Page 117: Place A Support Under Vehicle
Safe Operation - Driving Safely Place a support under vehicle. NOTE: Before jacking ensure that all wheels are locked� NOTE: When the brake lock is applied ensure that the vehicle stays securely in place� WARNING DO NOT OVERLOAD your jack beyond its rated capacity.
Page 118: Intended Use
Safe Operation - Driving Safely Intended Use The tractor is designed solely for use in agricultural or similar operations. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service, and repair as specified by the manufacturer, also constitute essential elements of the intended use.
Page 119: Winch Operation
Safe Operation - Driving Safely Winch Operation (Select Markets) Your vehicle may be equipped with a winch that can pull certain capacities and types of loads. It is useful for vehicle self-recovery when stuck, assisting another vehicle in recovery, moving fallen trees, removing brush, etc.
Page 120 Safe Operation - Driving Safely • Never winch up or down, or to the sides at sharp angles. This can destabilize the winching vehicle and possibly cause it to move without warning. • Never attempt to winch loads that weigh more than the winch capacity rating. •...
Page 121 Safe Operation - Driving Safely • If winching at an angle is unavoidable, follow these precautions while operating: ▪ Look at the winch drum occasionally. Never let the winch cable “stack” or accumulate at one end of the drum. Too much cable at one end of the drum can damage the winch and cable. ▪...
Page 122 Safe Operation - Driving Safely BEFORE YOU BEGIN - Realize that each winching situation is unique: • Take your time to think through the winch operation you are about to perform. • Proceed slowly and deliberately. • Never hurry or rush during winching. •...
Page 123 Safe Operation - Driving Safely WARNING: Never use a ‘recovery strap’ for winching. Recovery straps are designed to stretch and could release excessive energy that can result in SEVERE INJURY or DEATH if the strap or winch cable breaks. Use only undamaged tow straps or chains that do not stretch. 5�...
Page 124 Safe Operation - Driving Safely Vehicle Recovery Methods Vehicle Self-Recovery: • A. Release the winch drum and pull out the required length of cable. • B. Whenever possible, pick an anchor point that aligns the winch cable to the vehicle’s centerline as close as possible.
Page 125 Safe Operation - Driving Safely Recovery of Another Vehicle: • A. Release the winch drum and pull out the necessary length of cable. • B. Attach the winch hook to the vehicle. Whenever possible, pick an anchor point on the stuck vehicle that aligns the winch cable to the winching vehicle’s centerline as close as possible.
Page 126 Safe Operation - Driving Safely • A kinked winch cable made of wire rope that has been “straightened out”, even though it may look usable, has been permanently and severely damaged. It can no longer achieve its load capacity rating. Promptly discontinue use of a winch cable in this condition. •...
Page 127 Safe Operation - Driving Safely • B. Pull out the winch cable that is wrapped unevenly onto the drum. • C� Re-engage the winch drum� • D. Have an assistant pull the winch cable hook strap tightly to apply about 100 lbs. (45 kg) of tension. •...
Page 128 Safe Operation - Driving Safely • Never use recovery straps with your winch. This is a form of shock loading. Recovery straps are designed to stretch and can store energy. Stored energy in the recovery strap is released if a failure occurs, making the event even more hazardous.
Page 129: Maintenance
Maintenance Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment, and lubrication of important components are explained in the maintenance schedule. Inspect, clean, lubricate, adjust, and replace parts as necessary. When inspection reveals the need for replacement parts, always use genuine parts available from your dealer.
Page 130 Maintenance KEY POINTS OF LUBRICATION SCHEDULE: Check all components at the intervals outlined in the Periodic Maintenance Schedule. Items not listed in the schedule should be lubricated at the general lubrication interval. • Change lubricants more often under severe use, such as wet or dusty conditions. •...
Page 131: Pre-Ride Maintenance Checklist
Maintenance Pre-Ride Maintenance Checklist Perform these inspections before operating the vehicle: Maintenance before operation Item Hour Calendar Miles ( k m ) Remarks ■ Steering system Pre-Ride ■ Throttle return Pre-Ride Front suspension and axles Pre-Ride Visually inspect, test, Rear suspension and axles Pre-Ride or check components�...
Page 132 Maintenance Maintenance before operation Item Hour Calendar Miles ( k m ) Remarks Inspect. If deposits are visible, clean intake ► Air box sediment tube Pre-Ride tubes, air box, and replace air filter. Inspect. If deposits are visible, drain / clean ►...
Page 133: Break-In Maintenance Checklist
Maintenance Break-In Maintenance Checklist Perform these maintenance items when the 20-hour vehicle break-in is completed: Break-in Maintenance ( P erform at the interval that arrives first ) Item Hour Calendar Miles ( k m ) Remarks Lubricate all grease General lubrication 200 ( ...
Page 134 Maintenance Break-in Maintenance ( P erform at the interval that arrives first ) Item Hour Calendar Miles ( k m ) Remarks ► Brake pads 200 ( 3 20 ) Inspect pad thickness� Check terminals, Battery 200 ( 3 20 ) clean, test battery condition if required.
Page 135: Periodic Maintenance Schedule
Maintenance Periodic Maintenance Schedule Perform maintenance at the interval that arrives first after the 20-hour break-in period: Periodic Maintenance Intervals ( P erform at the interval that arrives first ) Item Hour Calendar Miles ( k m ) Remarks ► Brake pads Monthly 100 ( ...
Page 136 Maintenance Periodic Maintenance Intervals Item ( P erform at the interval that arrives first ) Hour Calendar Miles ( k m ) Remarks Inspect level� Change ► Front gear case oil 100h 1000 ( 1 600 ) yearly if hours or distance interval is not met�...
Page 137 Maintenance Periodic Maintenance Intervals Item ( P erform at the interval that arrives first ) Hour Calendar Miles ( k m ) Remarks Inspect; clean external surfaces. Clean more ► Radiator 500 ( 8 00 ) frequently if subjected to severe use�...
Page 138 Maintenance Periodic Maintenance Intervals ( P erform at the interval that arrives first ) Item Hour Calendar Miles ( k m ) Remarks Inspect� Replace ► ■ CVT drive belt 100h 1000 ( 1 600 ) as necessary� See dealer for service. Clean and Inspect pulleys�...
Page 139 Maintenance Periodic Maintenance Intervals Item ( P erform at the interval that arrives first ) Hour Calendar Miles ( k m ) Remarks Inspect fuel tank, cap, ● Fuel system 100h 500 ( 8 00 ) fuel pump and fuel pump relay�...
Page 140 Maintenance Periodic Maintenance Intervals Item ( P erform at the interval that arrives first ) Hour Calendar Miles ( k m ) Remarks Inspect for noise or ► ■ Wheel bearings 100h 1500 ( 2 400 ) looseness� Replace as necessary� Visually inspect belts and test latches�...
Page 141 Maintenance Periodic Maintenance Intervals ( P erform at the interval that arrives first ) Item Hour Calendar Miles ( k m ) Remarks Inspect fluid for color ► Brake fluid 200h 1000 ( 1 600 ) change. Change fluid every two years� Inspect for proper rpm.
Page 142: Inspection And Service Record
Maintenance Inspection and Service Record INSPECTION AND SERVICING MUST BE CARRIED OUT ACCORDING TO THE SCHEDULE DEFINED IN THIS OWNER’S MANUAL SERVICE RECORD Inspection Number Date Miles / Kilometer Dealer Stamp and/or Signature...
Page 143 Maintenance INSPECTION AND SERVICING MUST BE CARRIED OUT ACCORDING TO THE SCHEDULE DEFINED IN THIS OWNER’S MANUAL SERVICE RECORD Inspection Number Date Miles / Kilometer Dealer Stamp and/or Signature...
Page 144: Maintenance Procedures
Maintenance Maintenance Procedures Air Filter Check and change the air filter at the intervals outlined in the Maintenance Schedule. The air filter element should be cleaned or replaced more often if the vehicle is used in extremely dusty or wet areas. Each time air filter maintenance is performed, check the air inlet of the air filter box for obstructions and debris.
Page 145 Maintenance Air Filter Maintenance 1� Remove air filter protector ( 1 ) . 2� Loosen the 3 steel clasps and remove the air filter cover ( 2 ) . 3� Remove filter element ( 3 ) . 4�...
Page 146 Maintenance Drying the Air Filter Housing after Submersion If water has been ingested into the air filter housing, Drain the air filter housing, remove the air filter, and thoroughly dry the components. Do not use compressed air on the paper air filter. Contact your dealer if vehicle performance issues exist.
Page 147: Inspect The Engine Oil Level
Maintenance Inspect The Engine Oil Level 1� Place the vehicle on the level ground and park the vehicle. 2� Start the engine and idle for 30 seconds, then stop the engine. 3� Wait for a few minutes to allow the engine oil to settle down inside the engine�...
Page 148 Maintenance Change the Crankcase Oil 1� Place the vehicle on the level ground and park the vehicle. 2� Start the engine and warm for ( 2 ~3 ) minutes, then stop the engine� 3� Place a pan under the engine drain hole ( 1 ) to store the engine oil�...
Page 149 Maintenance 15� Use a dry and clean cloth to wipe the area around magnetic drain bolt. 16� Add the recommended type of oil into oil dipstick hole using the funnel, funnel extension tube and tube adapter that are supplied with the vehicle. Keep oil level in the specified range. 17�...
Page 150 Maintenance Change Transmission Oil 1� Place the vehicle on the level ground and park the vehicle. 2� Start the engine and warm for ( 2 ~3 ) minutes, then stop the engine� 3� Place a pan under the transmission drain hole ( 1 ) to store the oil�...
Page 151 Maintenance 10� Remove the funnel assembly. Verify the oil level is between the upper and lower mark with the dipstick, and adjust the oil level accordingly� CAUTION Too much or too little oil will have an impact on the normal operation of the engine. Make sure the oil is maintained between the upper and lower marks of the dipstick.
Page 152: Engine Valve Clearance Adjustment
Maintenance Engine Valve Clearance Adjustment The intake and exhaust valve clearances change with use of the vehicle, which can result in improper fuel/air supply or engine noise. To prevent this, the valve clearances must be adjusted according to the maintenance schedule.
Page 153: Front And Rear Gear Case
Maintenance Front and Rear Gear Case Inspect the front and rear gear case for any leaks before operating the vehicle, if found any leaks, stop operating the vehicle and contact with your dealer for inspection and service. Change the Front and Rear Gear Case Oil 1�...
Page 154 Maintenance Rear gear case oil volume: 13.5 oz. ( 4 00 mL ) 9� Mount the filling bolt and washer ( 3 ) . Torque for filling bolt: 18.4 ft-lb. ( 2 5 N·m ) 10� Dispose the used oil in a proper way� 11�...
Page 155: Front And Rear Axle Boots
Maintenance Front and Rear Axle Boots The front and rear axle boots ( 1 ) must be checked for holes or wear before operating. If any damage is found, have your dealer repair the vehicle.
Page 156: Cvt System
Maintenance CVT System This vehicle has a Continuously Variable Transmission ( CVT ) system that utilizes a drive belt and clutch pulleys to automatically vary transmission drive ratios, allowing infinite variability between the highest and lowest vehicle speeds with no discrete steps or shifts.
Page 157 Maintenance Avoiding CVT drive belt and clutch failures CVT clutch and belt life can be dramatically extended by avoiding these common operating mistakes: Causes CVT damage: Solution: Attempting to load the vehicle onto a truck bed or tall Shift transmission to low gear during loading of the trailer in high gear�...
Page 158 Maintenance Causes CVT damage: Solution Stuck in mud or snow� Shift the transmission to low gear, and carefully use fast, aggressive throttle application to engage CVT. WARNING: Excessive throttle may cause loss of control and vehicle overturn� Climbing over large objects from a stopped position. Shift the transmission to low gear, and carefully use fast, brief, aggressive throttle application to engage the CVT�...
Page 159 Maintenance What to do if water collects in the CVT housing If the vehicle was submerged in water deep enough that water has entered the CVT housing, remove the drain bolt ( 1 ) at the bottom of the housing to drain the water from the case. CAUTION If water drains from the CVT housing after removing the bolt, have your dealer inspect the vehicle, as water may have affected the CVT system and other engine parts.
Page 160: Cooling System
Maintenance Cooling System Inspect coolant level 1� Place the vehicle on the level ground and keep it in parking state� 2� Wait for the engine cooling down to ambient temperature, then inspect the coolant level� 3� Remove the front access cover. 4�...
Page 161 Maintenance Change the Coolant WARNING Never remove the radiator cap If the engine is hot. Wait for the engine to cool down before removing the radiator cap. Hot coolant can cause serious burns. 1� Place the vehicle on a level ground and keep it in parking state. 2�...
Page 162 Maintenance 9� During filling coolant, unscrew the coolant drain bolt to release residual air inside the coolant hose until only fluid flows out, then screw back in and tighten the drain bolt. Drain Bolt Torque: 7.4 ft-lb. ( 1 0 N·m ) 10�...
Page 163 Maintenance NOTE: Recommended antifreeze: Any high quality ethylene glycol antifreeze containing corrosion inhibitors for aluminum engines. CFMOTO recommended coolant freeze protection level: -35ºC. Antifreeze and water mixing ratio: 1: 1 Coolant capacity: 5.18 qt. ( 4 .9 L ) Coolant reservoir capacity: 0.36 qt. (0.41L) Cleaning the Radiator Cleaning the external surfaces of the radiator if it is covered with mud or debris will ensure it continues to efficiently cool the engine.
Page 164: Spark Plug
Maintenance Spark Plug( The spark plug ( 1 ) is an important engine component that is easy to inspect. The color and condition of the spark plug can indicate the condition of the engine. The ideal color on the insulator around the center electrode is a medium-to-light tan color for an engine that is being operated normally.
Page 165 Maintenance Spark Plug Removal and Inspection 1� Place and park the vehicle on a level ground. 2� Remove the spark plug cap. ( R emove the rear access cover before removing spark plug on the cylinder head ) 3� Remove the spark plug cap� 4�...
Page 166 Maintenance Spark Plug Removal to Expel Water from the Engine If water has been ingested into the engine, it is important to remove the water as soon as possible by removing the spark plug( s ) and using the starter system to rotate the engine for a short period to expel water out of the cylinder( ...
Page 167 Maintenance Exhaust Pipe Spark Plug Arrestor Clean the carbon deposits from the spark arrestor periodically. Blocked spark arrestor will decrease the engine power. After driving through mud or water, inspect the spark arrestor and clean it if necessary� WARNING The exhaust system temperature is very high just after operation. Touching the pipe may lead to serious injury�...
Page 168: Battery
Maintenance Battery This vehicle is equipped with a 12 volt / 30 Amp-hour, sealed low maintenance battery ( A ) . Therefore, it is not necessary to check the electrolyte or add distilled water into the battery. If the battery seems to be discharged, cover is damaged, or other problem exists, contact your dealer.
Page 169 Maintenance Battery Disassembly Place the vehicle on the level ground and park. Turn off the stop switch, turn the key to the OFF position, make sure the ignition system is in power off condition for the vehicle. Remove front access cover. Remove the black negative wire ( - ).
Page 170 Maintenance Battery Installation Place the vehicle on the level ground and park. Turn off the stop switch, turn the key to the OFF position, make sure the ignition system is in power off condition for the vehicle. Place the battery. Install the battery belt.
Page 171 Maintenance Battery Charging Remove battery. Connect the charger with the positive and negative end of battery. Switch on the charger� Note: It’s recommended to charge the battery with current 10% of the battery capacity. Disconnect the charger after finishing charging. Separate the charger and battery.
Page 172: Brakes
Maintenance Brakes Brake Fluid Level Inspection Before riding, check that the brake fluid level is above the low mark and replenish whenever necessary. The brake fluid reservoir is located under the front access cover. Insufficient brake fluid may let air enter the brake system, possibly causing the brakes to become ineffective.
Page 173 Maintenance • As the brake pads wear, it is normal for the brake fluid level to gradually go down. A low brake fluid level may indicate worn brake pads or brake system leakage. Therefore, be sure to check the brake pads for wear before checking the brake system for leakage.
Page 174 Maintenance Brake Fluid Change Complete brake system fluid replacement should be performed only by trained service personnel. Have your dealer replace the following components during periodic maintenance, or when they are damaged or leaking: • Replace the brake hoses every four ( 4 ) years. WARNING An over-full master cylinder may cause brake drag or brake lockup, which could result in an accident causing serious injury or death.
Page 175: Suspension Lubricating And Adjustment
Maintenance Suspension Lubricating and Adjustment Lubricating front swing arm bushing and rear stabilizer bar. Add lubricating grease into grease nipple ( 1 ) with a grease gun until it begins to flow from bushing. NOTE There are 4 grease nipples on front swing arm bushing, and two grease nipples on rear stabilizer bar, they are symmetrical in left and right.
Page 176 Maintenance Spring Preload Adjustment When riding on rough terrain conditions, using the hitch to tow, or carrying the maximum weight of people and cargo, increase the spring preload to get firmer riding. Decrease the spring preload as necessary for rough or soft terrain, to get smooth riding�...
Page 177 Maintenance Compression Damping Adjustment Compression damping ( 3 ) controls the suspension compression velocity. If the compression damping setting is higher, suspension compression velocity is slower. If the compression damping setting is lower, suspension compression velocity is quicker. Compression damping has A and B levels. Level A is for low-speed compression damping.
Page 178 Maintenance Increase the compression damping level A: LOW-SPEED COMPRESSION DAMPING ADJUSTMENT Low speed compression is adjusted using a flat-blade screwdriver in the middle of the adjuster. This adjustment primarily affects compression damping during slow suspension movements such as ride comfort of the vehicle and smooth jump landings. It also affects wheel traction�...
Page 179 Maintenance Increase the compression damping level B: HIGH-SPEED COMPRESSION DAMPING ADJUSTMENT High speed compression damping is adjusted using a 17mm socket or wrench. This adjustment primarily affects compression damping for medium-to-fast suspension movements such as steep jump faces, harsh flat landings and aggressive whoops. For optional performance, a suggested goal is to run the smallest setting of high-speed compression damping possible without bottoming the suspension.
Page 180 Maintenance Rebound Damping Adjustment Rebound damping is adjusted using a flat-blade screwdriver at the bottom of the shock. Rebound damping (C) controls the suspension rebound velocity after it has been compressed. If the damping setting is higher, the rebound velocity is slower. If the damping setting is lower, rebound velocity is faster.
Page 181: Wheels
Maintenance Wheels Tire Pressure Before operating the vehicle, use tire pressure pen to inspect the tire pressure: Front tire: When the load is less than195kgs: 14.5 PSI ( 1 00 kPa ) When the load is more than 195kgs: 16 PSI ( 1 10 kPa ) Rear tire: When the load is less than195kgs: 16 PSI ( ...
Page 182 Maintenance Change the Wheel Disassembling 1� Place the vehicle on a level ground. 2� Lift the vehicle and support the vehicle securely under the frame using a jack or other suitable tool so the wheel is off the ground� 3� Remove the hexagon slotted wheel nut ( 1 ) . 4�...
Page 183: Electrical
Maintenance Electrical Fuse Box The fuse box is located under the front access cover. If a fuse is blown, turn off the main switch and install a new fuse with specified amperage. Turn on the main switch. If the fuse blows again immediately, contact your dealer�...
Page 184 Maintenance Main Fuse and EPS Fuse A 40 Amp main fuse and a 40 Amp EPS (1) fuse are located under the front access cover. If the fuse is blown, turn off the main switch and install a new fuse of the specified amperage. Turn on the main switch. If the fuse immediately blows again, please contact your dealer.
Page 185 Maintenance Headlight Adjustment To adjust the headlight: Remove the front left and right access cover, which are located next to the left and right ROPS bars. Adjust the adjustment screw ( 1 ) to adjust the beam direction vertically� Adjust the adjustment screw ( 2 ) to adjust beam direction horizontally.
Page 186: Cleaning And Storage
Cleaning and Storage Washing the Vehicle Keeping your vehicle clean will not only improve its appearance, but it can also extend the life of various components. With a few precautions, your vehicle can be cleaned much like an automobile: • The best and safest way to clean your vehicle is with a garden hose and a pail of mild soap and water.
Page 187: Perform Repairs
Cleaning and Storage CAUTION Certain products, including insect repellant and other chemicals, will damage plastic surfaces. Use caution when using these products near plastic surfaces. Perform Repairs Make necessary repairs to your vehicle before storing to prevent further damage the next time you operate it. Check the Tires Inspect the tire treads and overall condition.
Page 188: Check Fluid Levels
Cleaning and Storage Check Fluid Levels Inspect the following fluid levels and change if necessary: • Front gear case • Rear gear case • Brake fluid ( c hange every two years or as required if fluid looks dark or contaminated ) •...
Page 189: Fog' The Engine
Cleaning and Storage ‘Fog’ the Engine • Remove the rear access cover to access the spark plug( s ) . • Remove the spark plug( s ) , rotate the piston to the bottom of its stroke, and pour approximately 2 oz. ( ...
Page 190: Transporting The Vehicle
Transporting the Vehicle Follow these procedures when transporting the vehicle: • Turn off the engine and remove the key to prevent loss during transporting. • Ensure the fuel cap is installed correctly and secure. • Ensure the seat is installed correctly and secure� •...
Page 191: Vehicle Issue Diagnosis
Vehicle Issue Diagnosis This section is intended to guide an average owner to simple items that could cause operating problems. Diagnosis of vehicle issues may require the experience of a dealership technician. Please contact your dealer if a solution is not apparent. Engine Starter Doesn’t Turn On Possible Cause Solution...
Page 192: Engine Stops Or Loses Power
Vehicle Issue Diagnosis Engine Stops or Loses Power Possible Cause Solution Clean radiator screen and external core. clean engine Overheated engine exterior. See your dealer Replace with minimum E10 or 95(RON) octane Out of fuel unleaded fuel Kinked or plugged fuel tank vent line Inspect and replace�...
Page 193: Engine Turns Over, Fails To Start
Vehicle Issue Diagnosis Engine Turns Over, Fails to Start Possible Cause Solution Engine turns over, Fails to start Refuel Clogged fuel filter Inspect and replace as necessary Replace with minimum E10 or 95(RON) octane Water is present in fuel unleaded fuel Fuel pump is inoperative Inspect pump and fuse;...
Page 194: Engine Turns Over, Fails To Start
Vehicle Issue Diagnosis Engine turns over, Fails to start Possible Cause Solution Worn or defective spark plug wires See your dealer Incorrect spark plug gap or heat range Set gap to specs or replace plugs Loose electrical connections Check all connections and tighten Low battery voltage Recharge battery to 12.8 Vdc;...
Page 195: Engine Backfires
Vehicle Issue Diagnosis Engine Backfires Possible Cause Solution Weak spark from spark plugs Inspect and replace spark plugs as necessary Incorrect spark plug gap or heat range Set gap to specs or replace plugs Replace with minimum E10 or 95(RON) octane Old or non-recommended fuel unleaded fuel Incorrectly installed spark plug wires...
Page 196: Efi Malfunction Indicator Light
AM 10:50 Vehicle Issue Diagnosis EFI Malfunction Indicator Light The Electronic Fuel Injection system on your vehicle contains a self-diagnostic feature that will illuminate the malfunction indicator light ( M IL ) if it detects a problem. When this indicator is on, please contact your dealer. During normal operation, the EFI indicator will be off.
Page 197: Eps Malfunction Indicator Light
AM 10:50 Vehicle Issue Diagnosis EPS Malfunction Indicator Light The Electronic Power Steering system on your vehicle contains a self-diagnostic feature that will illuminate the malfunction indicator light ( M IL ) if it detects a problem,when this indicator flashes, please contact your dealer.
Page 198: Electronic Power Steering ( E Ps ) Fault Diagnosis And Solution
Vehicle Issue Diagnosis Electronic Power Steering ( E PS ) Fault Diagnosis and Solution 1� Wire connectors have bad contact or are 1� Check whether wire connectors disconnected and pins are fully inserted 2� The fuse blew out 2�...
Page 199: Declaration
DECLARATION Declaration Declaration of Drivers exposure to noise level The undersigned: Lai Mingjie,General Manager Company name and address of the manufacturer: ZHEJIANG CFMOTO POWER CO., LTD. No.116, Wuzhou Road, Yuhang Economic Development Zone, Hangzhou, 311100 Zhejiang Province P.R.China Make (trade name of the manufacturer): CFMOTO Category, The Drivers Commercial name(s)
Page 200: Declaration Of Vibration Declaration
DECLARATION Declaration of Vibration declaration Driver mass CF1000UTR-B Requirement Test run1 0�67 Deviation<10% between test run 1/2 and 59kg±1kg Test run2 0�69 Arithmetic mean, a <1�25m/s A Arithmetic mean 0�68 Test run1 0�63 Deviation<10% between test run 1/2 and 98kg±5kg Test run2 0�60 Arithmetic mean, a...
Page 201: Cfmoto Limited Warranty
CFMOTO Limited Warranty CFMOTO LIMITED WARRANTY ZHEJIANG CFMOTO POWER CO., LTD gives a limited warranty on all components of your CFMOTO Vehicle against defects in material or workmanship within the period and under the conditions described below. This warranty covers parts and labor charges for repair or replacement of defective parts and begins on the date of purchase by the original retail purchaser.
Page 202 CFMOTO Limited Warranty REGISTRATION The Dealer must register the vehicle online and provide the completed registration form to ZHEJIANG CFMOTO POWER CO., LTD within ten (10) days of completing the sale of the vehicle. Please note that NO warranty claims will be processed unless the product warranty online registration form is completed and the form is received by ZHEJIANG CFMOTO POWER CO., LTD from the Dealer.
Page 203 CFMOTO Limited Warranty 12. Damage resulting from the vehicle has been altered or modified in such a way so as to adversely affect its operation, performance or durability, or has been altered or modified to change its intended use; 13. Incidental or consequential damages, or damages of any kind including without limitation towing, storage, telephone, rental, taxi, inconvenience, insurance coverage, loan payments, loss of time, loss of income etc.
Page 204 CFMOTO Limited Warranty ● Bushings ● Bearings ● Wheels and tires ● Finished and unfinished surface ● Suspension components ● Engine components ● Seat components ● Drive belts ● Clutches and components ● Hydraulic components and fluids ● Steering components ●...
Page 205 CFMOTO Limited Warranty HOW TO OBTAIN WARRANTY SERVICE The customer must cease using the CFMOTO Vehicle upon the appearance of an anomaly. The customer must notify a servicing CFMOTO dealer within three (3) days of the appearance of a defect, and provide it with reasonable access to the product and reasonable opportunity to repair it.
Page 206: Change Of Ownership
CFMOTO Limited Warranty Change of Ownership If you sell your vehicle, any valid remainder of the warranty can be transferred to the new owner. Please record the details of the exchange below and inform an authorized CFMOTO dealer: Change of Original Purchaser 2nd Owner 3rd Owner...
Page 207 5BYV-380101-3200-12 EU214 ZHEJIANG CFMOTO POWER CO., LTD. Add: NO.116, Wuzhou Road, Yuhang Economic Development Zone, Hangzhou 311100, Zhejiang Province, China Tel: 86-571-86258863 Fax: +86-571-89265788 E-mail: service@cfmoto.com.cn http: //global.cfmoto.com...

This manual is also suitable for:

Cf1000us Cf1000us-a Cf1000utr-b

CF MOTO ZFORCE 1000Sport Owner's Manual

Quick Links

Related Manuals for CF MOTO ZFORCE 1000Sport

Summary of Contents for CF MOTO ZFORCE 1000Sport

This manual is also suitable for:

Table of Contents