Page 1
CFORCE Owner's Manual READ THIS It contains important Operators under 10 are prohibited. MANUAL safety information No passengers are allowed. CAREFULLY...
FOREWORD Welcome Thank you for purchasing a CFMOTO vehicle, and welcome to our world-wide family of CFMOTO enthusiasts. Be sure to visit us online at www.cfmoto.com for the latest news, new product introductions, upcoming events, and more. CFMOTO is an international company that specializes in the development, manufacture, and marketing of all-terrain vehicles, utility vehicles, large displacement motorcycles, and their core components.
Page 7
DANGER This vehicle can be hazardous to operate. Before operating, drivers must meet the following basic requirements: 1. The driver’s age should be 10 years or older. 2. The driver should receive driving training from a certified instructor and be proficient with vehicle driving skills�...
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. E VAP System (Evaporative Emission Control System) (If equ ipped) When required by environmental emissions regulations, this vehicle is manufactured with a fuel evaporation system (EVAP) to prevent fuel vapors entering the atmosphere from the fuel tank and fuel system�...
FOREWORD Signal Words A signal word calls attention to a safety message or messages, a property damage message or messages, and designates a degree or level of hazard seriousness. The standard signal words in this manual are DANGER, WARNING, CAUTION and NOTE or NOTICE. The following signal words and symbols appear throughout this manual and on your vehicle.
Page 10
FOREWORD WARNING FOR TYPE I ATV (1-person vehicle) ALWAYS NEVER USE NEVER CARRY USE AN ON PUBLIC A PASSENGER� APPROVED ROADS� HELMET AND PROTECTIVE GEAR�...
Page 11
FOREWORD NEVER: • Operate without proper training or instruction. • Operate on public roads. A collision can occur with another vehicle. • Operate at speeds too fast for your skill or the conditions. • Use ALCOHOL or DRUGS before or while driving this vehicle. ALWAYS: •...
FOREWORD CFMOTO YOUTH APP This vehicle is equipped with safety features and a startup module that Guardians can control through the CFMOTO YOUTH App (see the QR code for the download address): • Access real-time information and running status of the vehicle •...
Page 13
FOREWORD READ THE OWNER’S MANUAL� FOLLOW ALL INSTRUCTIONS AND WARNINGS� WARNING Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels. Failure to follow the safety precautions could result in serious injury or death. Warning All assembly work must be done by adults.
INTRODUCTION Thank you for purchasing a CFMOTO vehicle, and welcome to our world-wide family of CFMOTO enthusiasts. For safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this owner’s manual. Information about major repairs are outlined in the CFMOTO Service Manual, and should only be performed by a CFMOTO service dealer and technician.
INTRODUCTION Vehicle Identification Numbers and Key Information Record your vehicle’s identification numbers in the spaces provided. This vehicle is equipped with one key switch and 2 keys, if both keys are lost, contact your authorized dealer for a new key switch. Vehicle Identification Number: Vehicle Frame Number: Engine Number:...
Page 17
TECHNICAL SPECIFICATIONS Items Specifications Bore x Stroke 52�4 mm x 49�5 mm Displacement 107 cc Compression Ratio 9.1:1 Starting Type Electric Start Fuel Supply System Electronic Fuel Injection (EFI) Lubrication Type Pressure / Splash lubrication Engine Oil Type SAE 15W-40 / SAE 10W-40 / SAE 5W-40 Engine Oil Replacement 0.69 qt (650 mL) Air Filter...
Page 18
TECHNICAL SPECIFICATIONS Items Specifications Suspension Front Shock Absorber Oil damper, 5 position preload adjustable Rear Shock Absorber Oil damper, 4 position preload adjustable Electrical System Ignition APP / START button Battery 12V 5Ah Light System Headlight Position Light 28*2�43W Tail light / Brake Light 32*0�6W/12*3�2W APP Control Position...
ATV� Age Restrictions CFORCE 110 Operation is prohibited for anyone under the age of 10. No passenger is allowed on this vehicle. Children differ in skills, physical abilities and judgment. Some children may not be able to operate an ATV safely.
OPERATOR SAFETY Equipment Modifications CFMOTO is concerned with the safety of our customers and for the general public. Therefore, we strongly recommend that consumers do not install on a vehicle, any equipment that may increase the speed or power of the vehicle, or make any other modifications to the vehicle for these purposes. Any modifications to the original equipment of the vehicle create a substantial safety hazard and increase the risk of body injury.
OPERATOR SAFETY Safety Training When you purchased your new ATV, your dealer offered a hands-on safety training course that covers all aspects of vehicle safety. You were also provided with printed materials that explain safe operating procedures. You should review this information on a regular basis. If you purchased a used ATV from a party other than a dealer, you can request safety training from any authorized dealer.
Page 22
OPERATOR SAFETY • Always keep both hands on the handlebars and both feet on the footrest of the ATV during operation� • Always travel slowly and use extra caution when operating on unfamiliar terrains. Be alert to terrain conditions� • Never operate on excessively rough, slippery, or loose terrains.
Page 23
OPERATOR SAFETY • Always use proper procedures if you stall or reverse while climbing a hill. To avoid stalling, maintain a steady speed when climbing a hill. If you stall or roll backwards, follow the special procedure for braking described in this manual. Always dismount on the uphill side, or to either side if the ATV is pointed straight uphill.
OPERATOR SAFETY Potential Hazards and How To Avoid Them WARNING POTENTIAL HAZARD: Operating this ATV without proper instruction. WHAT CAN HAPPEN: The risk of an accident is greatly increased if the operator does not know how to operate this vehicle properly in different situations and on different types of terrain.
Page 25
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operation on paved surfaces such as sidewalks, trails parking lots, or public highways and streets. WHAT CAN HAPPEN: ATV tires are designed for off-road use. Driving on paved surfaces greatly affects how an ATV handles, which can result in loss of control and/or an accident.
Page 26
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operating this ATV without wearing an approved helmet, eye protection, and protective clothing. WHAT CAN HAPPEN: Operating an ATV without an approved helmet increases the risk of a severe head injury or death in the event of an accident. Operating without eye protection could result in an accident and could increase the chance of a severe eye injury in the event of an accident.
Page 27
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operating the ATV after consuming alcohol or drugs. WHAT CAN HAPPEN: Consumption of alcohol and/or drugs could seriously affect operator’s judgment. Reaction time may be slower and operator’s balance and perception could be affected. Consumption of alcohol and/or drugs before or while operating an ATV could result in an accident causing severe injury or death�...
Page 28
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operating the ATV at excessive speeds� WHAT CAN HAPPEN: Excessive speed increases the operator’s chance of losing control of the ATV, which can result in an accident. HOW TO AVOID THE HAZARD: Always operate the ATV at a speed that’s proper for the terrain, visibility and operating conditions, and your experience.
Page 29
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Failure to inspect the ATV before operating. Failure to properly maintain the ATV. WHAT CAN HAPPEN: Poor maintenance increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD: Always inspect your ATV before each use to make sure it’s in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual.
Page 30
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Failure to use extra caution when operating the ATV on unfamiliar terrain. WHAT CAN HAPPEN: Unfamiliar terrain may contain hidden rocks, bumps, or holes that could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Travel slowly and use extra caution when operating on unfamiliar terrain.
Page 31
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Failure to use extra caution when operating on excessively rough, slippery or loose terrain. WHAT CAN HAPPEN: Operating on excessively rough, slippery or loose terrain could cause loss of traction or loss of control, which could result in an accident or overturn.
Page 32
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Turning improperly. WHAT CAN HAPPEN: Improper turns could cause loss of control and lead to a collision or overturn. HOW TO AVOID THE HAZARD: Always follow proper procedures for turning as described in the owner’s manual. Practice turning at slow speeds before attempting to turn at faster speeds.
Page 33
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Climbing excessively steep hills or climbing hills improperly. WHAT CAN HAPPEN: Improper hill climbing could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Never operate on hills too steep for the ATV or for your abilities. Practice on smaller hills before attempting large hills.
Page 34
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Traveling down excessively steep hills� WHAT CAN HAPPEN: Improper downhill travel could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Never operate on hills too steep for the ATV or for your abilities. Practice on smaller hills before attempting large hills.
Page 35
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Improperly crossing hills and turning on hills. WHAT CAN HAPPEN: Improperly crossing or turning on hills could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Never attempt to turn the ATV around on any hill until you’ve mastered the turning technique on level ground as described in the owner’s manual.
Page 36
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Stalling, rolling backwards or improperly dismounting while climbing a hill. WHAT CAN HAPPEN: The vehicle could overturn. HOW TO AVOID THE HAZARD: Maintain a steady speed when climbing a hill. IF ALL FORWARD SPEED IS LOST: Close the throttle.
Page 37
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Improperly operating over obstacles. WHAT CAN HAPPEN: Operating over obstacles could cause loss of control or overturn. HOW TO AVOID THE HAZARD: Before operating in a new area, check for obstacles. Avoid operating over large obstacles such as rocks and fallen trees when possible.
Page 38
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Skidding or sliding� WHAT CAN HAPPEN: Skidding or sliding can cause loss of control. If the tires regain traction unexpectedly, the ATV could overturn. HOW TO AVOID THE HAZARD: On slippery surfaces such as ice, travel slowly and use extra caution to reduce the chance of skidding or sliding out of control.
Page 39
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operation of the ATV through deep or fast-flowing water. WHAT CAN HAPPEN: The tires may float, causing loss of traction and loss of control, which can lead to an accident or overturn. HOW TO AVOID THE HAZARD: Avoid operating the ATV through deep or fast-flowing water.
Page 40
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Improperly operating in reverse� WHAT CAN HAPPEN: The ATV could collide with an obstacle or person, resulting in severe injury. HOW TO AVOID THE HAZARD: Before shifting into reverse gear, always check for obstacles or people behind the ATV. When it’s safe to proceed, back slowly.
Page 41
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operating the ATV with improper modifications. WHAT CAN HAPPEN: Improper installation of accessories or modification of the ATV may cause changes in handling which could lead to an accident� HOW TO AVOID THE HAZARD: Never modify the ATV through improper installation or use of accessories. All parts and accessories added to the vehicle must be genuine parts or equivalent components designed for use on this ATV and should be installed and used according to approved instructions.
Page 42
OPERATOR SAFETY WARNING POTENTIAL HAZARD: Operating on frozen bodies of water. WHAT CAN HAPPEN: Severe injury or death can result if the ATV and/or the operator fall through the ice. HOW TO AVOID THE HAZARD: Never operate the ATV on a frozen body of water.
Page 43
OPERATOR SAFETY WARNING Before operating the vehicle, inspect the frame and handlebars for cracks or broken connection points. Aggressive operating or crashing into objects may damage or destroy the frame or handlebars. WARNING After any rollover or accident, have an authorized dealer inspect the entire vehicle for possible damage, including ( ...
OPERATOR SAFETY Safe Riding Gear Guardians should provide wear safe riding gear for children, including: 1� An approved helmet 2� Goggles 3� Gloves 4. Long-sleeved shirts or jackets 5� Long pants 6� Over-the-ankle boots According to the actual weather, you may need extra apparel, such as anti-fog goggles, thermal underwear and a face guard for cold weather.
Page 45
OPERATOR SAFETY An open-face helmet can not offer the same protection for your face and jaw. Please wear detachable face masks and goggles when wearing an open-face helmet. Do not depend on eyeglasses or sunglasses for enough eye protection, as they may fly out or shatter in case of an accident to cause second damage, and they can not prevent wind and airborne objects from getting into eyes�...
Page 46
OPERATOR SAFETY Jackets, Pants and Motorcycle Suits Wear a jacket or a long-sleeved shirt and long pants, or a full set of riding suit. Quality protective gear will provide comfort, and it can help you avoid being distracted by adverse environmental elements. In case of an accident, good quality protective gear made of sturdy material may prevent or reduce injury.
Safety Decals & Locations Warning decals have been placed on the ATV for your protection. Read and follow the instructions of each decal on the vehicle carefully. If a decal becomes illegible or comes off, contact your dealer for replacement. Warning decals in the owner’s manual are for reference.
FEATURES & CONTROLS FEATURES & CONTROLS Left Hand Controls Start switch Short press the button, the horn will sound. Stop Switch When the button is released, the electrical system stops working� When the button is pressed, the electrical system starts working�...
Page 51
FEATURES & CONTROLS Horn Button Press the start switch to start the vehicle� Safety Lock and Safety Lanyard For the vehicle to operate, the end of the safety lanyard must be connected on the safety lock seat as shown. The other end of the safety lanyard should be connected to a part of the operator’s body that is higher than the hand position.
Page 52
FEATURES & CONTROLS Hand Brake Fluid Reservoir and Level Indicator Check the hand brake master cylinder fluid level before each use of the ATV. The hand brake master cylinder is located on the right handlebar. The fluid level can be viewed through the indicator window on the side of the master cylinder.
Page 53
FEATURES & CONTROLS Hand Brake Lever (including hydraulic parking) The hand brake lever is located on the left handlebar and controls the front brake. Pull the lever toward the handlebar to apply the brakes. When squeezed, the lever should feel firm. Any spongy situation would indicate a possible fluid leak or low master cylinder fluid level, which must be corrected before riding.
FEATURES & CONTROLS Right Hand Controls Throttle Lever When the motor is running, press the throttle lever to increase motor’s running speed. The vehicle speed is adjusted by changing the position of throttle lever. The throttle lever is a spring-return type. If the operator’s hand is removed from the throttle lever, the vehicle will slow down and the motor will return to an idle state.
Page 55
FEATURES & CONTROLS Mechanical Speed Limiter A mechanical speed limiter keeps the throttle from fully opening, even when the throttle lever is pushed to maximum travel. Turning in the screw limits the throttle lever travel, which reduces the maximum engine power available and decreases the maximum speed of the ATV.
FEATURES & CONTROLS Foot Brake The foot brake pedal is located on the right side floor board of the vehicle. Stepping down on the pedal applies the front and rear brakes at the same time. When applied, the pedal should feel firm. A soft brake pedal would indicate a possible fluid leak or low master cylinder fluid level, which must be corrected before riding.
FEATURES & CONTROLS Foot Brake Reservoir Fluid Level Inspection The foot brake reservoir is located at the front right side of the vehicle, where the fluid level can be viewed directly. When the brake fluid is lower than “MIN” level, please fill the reservoir with DOT4 brake fluid to the position between the upper and lower lines.
Page 58
FEATURES & CONTROLS Seat The seat lock is under the seat at the vehicle rear. To remove, pull the lock outward and remove the cushion �...
FEATURES & CONTROLS ELECTRONIC FENCE (Available in Select Markets) Electronic fence receiver (shown at right): This vehicle is equipped with an electronic fence receiver. The guardian must carry the receiver when the vehicle is used. The electronic fence receiver is already paired with the vehicle at the factory.
FEATURES & CONTROLS About CFMOTO YOUTH App The guardian can set an electronic fence range using the CFMOTO RIDE YOUTH App installed on a mobile device. The app will remind the guardian if an operator is driving out of the electronic fence range and the guardian should alert the operator to return inside the range of electronic fence.
FEATURES & CONTROLS Electronic Fence Operation The functions can be only used inside the available range of the receiver and vehicle� Range Radius: 0~1312ft (0m ~ 400 m)� Turning on: Turning on the receiver by long press ON/OFF for 1 second. The receiver's buttons can then be used. Turning off: If the receiver is turned on or the vehicle is connected to APP by Bluetooth, and there is no operation for 30 seconds, the receiver will be turned off automatically;...
Page 62
FEATURES & CONTROLS Indicator Micro USB charging port NOTE: Charging input allowed by the electronic fence receiver: DC 5V; If the receiver has a fault, the indicator will not flash and the receiver cannot be charged. If this happens, please contact your dealer�...
FEATURES & CONTROLS Electronic Fence Receiver - Pairing With The Vehicle 1� Ensure the vehicle and receiver are powered off. 2� Power on the vehicle, then turn on the receiver and complete the steps 3 and 4 within one minute; if it takes more than a minute, please power off and then power on the vehicle, and turn on the receiver again.
FEATURES & CONTROLS Electronic Fence Receiver QR Code Please apply a QR code sticker at this position: Device Codes (ten numbers and characters): Guardians can input the device code on the CFMOTO YOUTH App to connect the receiver. Device codes can be obtained from an backup QR code and a label on the vehicle's electric fence transmitter.
Page 65
FEATURES & CONTROLS NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 66
FEATURES & CONTROLS RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter�...
FEATURES & CONTROLS Fuel Tank Fuel tank cap is located at the front of the vehicle. Open the fuel tank cap to fill fuel. Fuel Minimum Octane Rating The recommended fuel for your ATV is minimum 89 Octane unleaded (maximum 10% ethanol is allowed). Non-oxygenated (ethanol-free) fuel is recommended for best performance in all conditions�...
FEATURES & CONTROLS Gear Shift Lever Gear Shift Lever is located at the right front side of the vehicle� CAUTION Before shifting the gear, the ATV should be stopped and foot brake should be applied. If operators are shifting when the motor RPM is higher than the idling speed or the vehicle is moving, transmission damage may occur.
FEATURES & CONTROLS Front Service Cover Your vehicle is equipped with a service board at the front. Removal: 1. Remove the seat; 2. Remove the fuel tank cap; 3. Remove two bolts at the fuel tank’s rear cover, and remove the rear cover;...
Page 70
FEATURES & CONTROLS Tool Kit Tool Kit is located under the seat.
FEATURES & CONTROLS Dashboard Indicators and Warnings...
Page 72
FEATURES & CONTROLS 1 Speedometer 2 Gear Position Display 3 Odometer 4 EFI fault indicator 5 Safety Lock State Indicator 6 Electronic Fence Indicator 7 Parking indicator 8 Headlight Indicator 9 Fuel Gauge 1� Speedometer The current speed is displayed here. (Unit setting: Quickly shift the light switch 5 times within 5 seconds after powering on the vehicle.) 2�...
Page 73
FEATURES & CONTROLS 6� Electronic Fence Indicator (Available in Select Markets) This indicator will be on when the vehicle is out of the range of electronic fence. This indicator will be on when the vehicle is out of the range of electronic fence. The guardian can set electronic fence range in the mobile CFMOTO RIDE YOUTH App.
OPERATING YOUR VEHICLE Break-In Period The break-in period for a new engine is very important. Careful treatment of a new engine at the beginning of ownership will contribute to more efficient performance and longer life. Perform the following procedures carefully: 1.
OPERATING YOUR VEHICLE WARNING When the vehicle is being started, please grip the handbrake or step on the footbrake. Gear Shifting Follow these steps to shift the gear: • Make sure the throttle is off and the vehicle is completely stopped; •...
OPERATING YOUR VEHICLE Responsibility of Operators and Guardians The driver should be supervised by a parent or guardian at all times. The driver should wear the required safety riding gear. Recreational, Group, and Distance Riding One of the benefits of this vehicle is that the operator can go off-road driving under the supervision of parents or guardians within allowed areas, such as trails for snowmobiles, equestrian, mountain bikes or other places designated for ATV use.
Page 77
OPERATING YOUR VEHICLE Follow the items below to reduce the risk of accidents: • Be careful when making turns, and reduce speed before entering into turns. • Select suitable turning angles according to the speed and environment. • Do not make abrupt or hard braking actions when turning. •...
Page 78
OPERATING YOUR VEHICLE Avoiding Collisions Never operate at excessive speeds. Always operate at a speed that is proper for the terrain, visibility, and operating conditions, and your experience. This vehicle does not have the same kind of protection for collisions as a car; for example, there are no air bags, no cab that is fully enclosed, no safety belt, and it is not designed for collisions with other vehicles.
OPERATING YOUR VEHICLE Practice Exercises Before you go out for a ride, it is very important to familiarize yourself with the handling of your vehicle by practicing in a controlled environment� Under the protection of a parent or guardian, find a suitable area to practice and perform the following exercises.
Page 80
OPERATING YOUR VEHICLE Basic Operation Steps Familiar yourself with start on and shifting operations, then practice the following basic steps: • Check your surroundings and determine your path of travel. • Sit upright with both feet on the footrests and both hands on the handlebars. •...
Page 81
OPERATING YOUR VEHICLE Turning Exercises Turning is a basic driving technique, and it is one of the most frequent causes of accidents. It is easy for the vehicle to lose traction or rollover if you turn too sharply, or go too fast while turning.
Page 82
OPERATING YOUR VEHICLE WARNING Turning sharp angles or at excessive speeds can result in vehicle’s rollover and lead to serious injury. The higher the turning speed, the higher the risk of rollover. It is prohibited to turn at high speeds. Abrupt changes of throttle during turning may lead to loss of balance or rollover.
Page 83
OPERATING YOUR VEHICLE Reverse Exercise Reverse is another basic driving technique. Due to the vision limitation, reversing operation is more dangerous than normal driving actions. Please check the surroundings carefully to reduce the risk of accidents� Reverse Vision ATV has smaller blind spots, but it is still important to keep alert. •...
Page 84
OPERATING YOUR VEHICLE Practice turning during reverse following the steps below: • Shift to “R”. • Check if any people, obstacles or downhill behind you. • Steer in the direction of the turn, with the turning angle as large as possible to reduce the risk of rollover.
OPERATING YOUR VEHICLE Off-Road Operation Off-road operation on natural terrain is dangerous. Any terrain which has not been specially prepared to carry vehicles presents an inherent danger where terrain substance, shape, and steepness are unpredictable. The terrain itself presents a continual element of danger, which must be knowingly accepted by anyone venturing over it.
Page 86
OPERATING YOUR VEHICLE Driving on Slippery Surfaces Slippery surfaces include wet trails, loose gravel or any surfaces during freezing weather. Slippery surfaces will result in skidding, rollover, longer braking distance and so on. Driving on cobblestone surfaces may cause loose stones to be ejected, which could hit other people or influence other’s routine.
Page 87
OPERATING YOUR VEHICLE Driving on Rough Terrain • Never drive in rough terrain. Driving over Obstacles Obstacles include rocks, fallen trees, and depressions. Improperly crossing over obstacles may lead to rollover or lead people to be ejected out of the vehicle. Follow these precautions: •...
Page 88
OPERATING YOUR VEHICLE Driving on Hillsides Operting on hillsides for young drivers is not recommended. If it is unavoidable to drive on hillsides, please observe the following precautions: Uphill Driving Whenever traveling uphill, follow these precautions: • Check the slope, avoid steep hills with a slope of 10°. •...
Page 89
OPERATING YOUR VEHICLE Driving Downhill When traveling down a hillside, follow these precautions: • Check the slope, avoid steep hills with a slope of over 10°. • Keep your center of gravity backward. • Always travel straight downhill and keep a steady speed� •...
MAINTENANCE Careful and periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment, and lubrication of important components are explained in the Periodic Maintenance Chart� Inspect, clean, lubricate, adjust, and replace parts as necessary. When inspection reveals the need for replacement of certain parts, always use original parts from your dealer.
Page 91
NOTE: Owners should adjust periodic maintenance intervals according to actual operating conditions, driving environment and other factors� The recommended maintenance periods that CFMOTO suggests is based on general use of the vehicle under ideal driving conditions� Observe and record the use of tires, the drive system and braking system, and flexibly adjust your periodic maintenance accordingly, rather than rigid following of the recommended maintenance schedule�...
Page 92
KEY POINTS OF LUBRICATION SCHEDULE: Check all components at the intervals outlined in the Periodic Maintenance Chart. Items not listed in the schedule should be lubricated at the general lubrication interval. • Change lubricants more often under severe conditions, such as being used in wet or dusty conditions�...
Pre-ride Maintenance Check Before each use of the vehicle, a best practice is to check the vehicle according to the Pre-ride Maintenance Check� WARNING If a proper inspection is not done before each use, severe damage to the vehicle, severe injury, or death could occur.
Break-in Periodic Maintenance Chart Maintain the following item that reaches the interval first within 20 hours or specified intervals. ▲ Break-in Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Lubricate all grease General lubrication 200 (320) points, pivots, cables,...
Page 95
▲ Break-in Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month C h e c k t e r m i n a l s , Battery 200 (320) clean, test battery condition if required Te s t p r o p e r r p m �...
Periodic Maintenance Schedule Maintain the following item that reaches the interval first after 20-hour break-in period. ▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month ► Brake pad 100 (160) Inspect pad thickness� Check terminals�...
Page 97
▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Inspect; clean external surfaces. Clean more ► Radiator 500 (800) frequently if subjected to severe use. ■ Steering system 500 (800) Inspect. Lubricate. L u b r i c a t e .
Page 98
▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Inspect routing. Replace filter and Fuel filter and hoses 2000 (3200) high-pressure hoses every 4 years� Inspect and adjust if necessary. ► Valve clearance 2000 (3200) Contact dealers for...
Page 99
▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Inspect fuel tank, cap, ● Fuel system 500 (800) fuel pump and fuel pump relay. Inspect; Replace if Spark plug 2000 (3200) worn or fouled.
Page 100
▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Inspect for noise or Bearings 1500 (2400) looseness. Replace ► ■ if necessary. Inspect fluid color change� Brake fluid 1000 (1600) ► Change brake fluid every two years�...
Page 101
▲ Periodic Maintenance Interval (Maintain the item that reaches the interval first) Item Miles (km) Notes Hour Month Test proper rpm� Contact dealers Idle condition for maintenance if the rpm is out of spec or erratic. Inspect steering system� Contact Steering dealers for maintenance whenever ■...
Engine Oil Inspection Inspect the Engine Oil Level • Place and park the vehicle on level ground. • Start and idle the engine for 30 seconds, and then stop the engine� • Wait for a short time to allow the engine oil to settle down inside the engine�...
Engine Oil Change • Place and park the vehicle on level ground. • Start and idle the engine for 2-3 minutes, and then stop the engine� • Place a pan under the engine oil drain hole to collect the used engine oil. •...
Page 104
NOTE Too much or too little oil will have an impact on the normal operation of the engine. Make sure the oil is maintained between the upper and lower marks of the dipstick. • Install and tighten the oil dipstick� •...
Air Filter There is a check hose at the bottom of the air filter housing. If dust or water can be viewed in this hose, empty the hose and clean the air filter housing thoroughly. NOTE: If there is a large amount of water in the air filter, have your dealer check the engine crankcase�...
Page 106
• Install the steel screen and a filter element. Apply a layer of lubricating oil on the inner diameter of air filter rubber sealing ring� • Install air filter cover and clamps. Ensure the filter is installed correctly and completely sealed� NOTE The air filter must be checked and replaced more often if the machine is operated in extremely dusty areas or if it...
Page 107
Spark plug inspection Remove the spark plug cap. Use the spark plug wrench in the tool kit to remove the spark plug. Inspection The spark plug is an important engine component and is easy to inspect. The condition of the spark plug can indicate the condition of the engine.
Page 108
Measure the electrode gap with a thickness gauge, and if necessary, adjust the gap to specification. NOTE: Spark plug gap : 0.6 mm ~ 0.7 mm 0.6 mm ~ 0.7 mm Installation 1� Clean the gasket surface. Wipe off any grime from the threads�...
Spark Arrestor Clean the spark plug arrestor when the muffler and exhaust pipe is at a normal temperature. • Remove nuts(1); • Remove the spark arrestor(2); • Tap the exhaust pipe gently and use a steel brush to clean any carbon deposits from the spark arrestor;...
MAINTENANCE & LUBRICATION Braking System Brake Fluid Inspection Front brake fluid reservoir is located at the left handlebar. Inspect if brake fluid level is between the upper and lower marks through the indicator window �...
Page 111
MAINTENANCE & LUBRICATION Brake Pad Inspection Front brake lever free play : Please contact your dealer for inspection� DANGER After servicing: • Make sure the brakes operate smoothly and the lever free play is correct. • Make sure the brakes do not drag and the brake operation is not spongy�...
Page 112
MAINTENANCE & LUBRICATION Brake Pad Inspection Check the brake pads for damage and wear. If the pad thickness is less than �059 in� (1�5 mm) or the disc thickness is less than .118 in. (3.0 mm), have your dealer replace them. Replacement of brake components requires professional knowledge.
Page 113
MAINTENANCE & LUBRICATION Brake Fluid Change Complete fluid replacement should be done only by trained maintenance personnel. Have your dealer replace the following components during periodic maintenance or when they are damaged or leaking. Replace the brake hoses every four years. Inspect the brake fluid level to see if it is between the upper and lower marks.
Page 114
MAINTENANCE & LUBRICATION CAUTION • When checking the front brake fluid level, make sure the master cylinder reservoir is level by turning the handlebar until the steering is centered and the wheels are forward. • Use only the designated quality brake fluid. Otherwise, the rubber seals may deteriorate, causing leakage and poor brake performance.
MAINTENANCE & LUBRICATION Foot Brake Pedal Height Adjustment The top of the brake pedal should be positioned 60 mm ~ 70 mm above the top of the footrest. If it is beyond the specification, contact your dealer to adjust it. DANGER Following the requirements: •...
MAINTENANCE & LUBRICATION Wheel and Tires Removal and Installation Removal: • Elevate the vehicle using a jack and support stands. • Remove four bolts � • Remove the wheel for replacement. Installation: • Install the wheel and the nuts � •...
Page 117
MAINTENANCE & LUBRICATION Tire Pressure Inspect the tire pressure before riding: Tire: Front tire: AT19×6-10 5.0 psi (35 kPa) Rear tire: AT18×9-8 5.0 psi (35 kPa) Tread Depth Inspect the tread depth regularly and replace the tires if the minimum tread depth is less than: Minimum tread depth: 0.06 in.
MAINTENANCE & LUBRICATION Drive Chain Inspection Drive chain slack and lubrication must be checked daily before riding in accordance with the Periodic Maintenance Chart for safety and preventing excessive wear. If the chain becomes badly worn or maladjusted, it will make chain too loose or too tight. If chain is too tight, it will accelerate wear of the chain, sprocket, rear sprocket and rear bearings.
Page 119
MAINTENANCE & LUBRICATION Chain Tension Inspection Shift to Neutral gear; Push up the chain and check its tension; If the chain tension is out of specification, adjust it to the standard� Standard value: 0�19 in� ~ 0�59 in� (5 mm ~ 15 mm)� NOTE: The wear of chain is not always the same.
MAINTENANCE & LUBRICATION Chain Adjustment Remove sprocket cover; Loosen the bolts ; Loosen the bolt ; Use a spanner to rotate the axle housing � Adjust chain tension to the standard range. Tighten the bolts �...
MAINTENANCE & LUBRICATION Battery This machine is equipped with a low-maintenance battery which is located under the seat. Therefore, it is not necessary to check the electrolyte or add distilled water in the battery. If the battery seems to have discharged, consult your dealer. Battery specification: 12V 5Ah.
Page 122
MAINTENANCE & LUBRICATION Fuse Box The fuse box is located under the seat. Relay Box The relay box is located under the seat.
Page 123
MAINTENANCE & LUBRICATION Battery Maintenance Guidelines: • If the vehicle will not be used for a month or longer, remove the battery and store it in a cool, dry place with good ventilation� • A special battery charger (constant low voltage/ampere) is required for charging low maintenance batteries.
MAINTENANCE & LUBRICATION Lights Position Light bulb replacement Position Light bulb replacement Both position light and taillight assembly are LED lights, which cannot be repaired if damaged or failed. Please have your dealer replace the entire assembly when the LED light is damaged or failed. Position light adjustment Position light is not adjustable.
MAINTENANCE & LUBRICATION Front and Rear Shock Absorber Standard Shock Absorber The spring preload can be adjusted to suit the rider’s weight and riding conditions� Adjust the spring preload as follows: To decrease the spring preload by turning the adjusting ring in direction �...
Page 126
MAINTENANCE & LUBRICATION Lubrication Recommended lubricant: All-Season Grease Grease nipples on rear suspension , rear shaft � Use a grease gun to add grease into the nipples until grease lightly flows from the bushing.
Cleaning & Storage Cleaning the ATV Keeping your ATV clean will not only improve its appearance, but it can also extend the life of various components. With a few precautions, your ATV can be cleaned much like an automobile. WARNING Before cleaning, batteries should be kept out of reach of children�...
CLEANING & STORAGE Preparation for Storage Clean the entire vehicle thoroughly. NOTE: After cleaning, please check the condition of the whole vehicle to prevent a residue of water. DANGER Oils used on motorcycles are toxic and used oils should be well disposed of. Keep them out of reach of children.
Page 129
CLEANING & STORAGE Waxing the ATV Your ATV can be waxed with any non-abrasive automotive wax. Avoid the use of harsh cleaners since they can scratch the vehicle’s surface. CAUTION Certain products, including insect repellents and chemicals, will damage plastic surfaces. Use caution when using these products near plastic surfaces.
CLEANING & STORAGE Battery Storage Remove the battery from the vehicle and ensure that it is fully charged before placing it in storage. Protect the battery from freezing temperatures, which can damage the battery. Lubrication Inspect all cables and lubricate them with cable lubricant according to instructions. Add all-season grease onto the vehicle’s lubricating points.
CLEANING & STORAGE Storage Area and Covering Reduce tire pressure to be specified and support the vehicle. Make sure the storage area is well ventilated and cover the vehicle with a ATV cover� In the case of rainy or snowy weather, the vehicle should be stored indoors. NOTE Do not use plastic or coated materials.
VEHICLE DIAGNOSIS VEHICLE DIAGNOSIS This section is intended to guide an average owner to know some simple items that could cause operating problems. Diagnosis of vehicle issues may require the experience of a technician. Please contact your dealer if a solution is not efficient. Engine Does not Turn Over Possible Cause Solution...
Page 133
VEHICLE DIAGNOSIS Engine Stops or Loses Power Possible Cause Solution Clean the radiator and the outside of core Overheated engine components. Clean engine’s surface. Contact your dealer� Fuel shortage Use 89 or higher octane unleaded fuel. Kinked or plugged fuel tank vent line Inspect and replace.
Page 134
Engine Turns Over, Fails to Start Possible Cause Solution Engine turns over, Fails to start Refuel. Clogged fuel filter Inspect and replace if necessary. Replace the fuel with 89 or higher octane unleaded Water in fuel fuel. Inoperative fuel pump Inspect pump and fuse;...
Page 135
Engine Backfires Possible Cause Solution Weak spark from spark plugs Inspect and replace spark plugs if necessary Incorrect spark plug gap or heat range Set gap to specs or replace plugs Replace the fuel with 89 or higher octane unleaded Old or non-recommended fuel fuel.
Page 136
Engine turns over, Fails to start Possible Cause Solution Fouled or defective spark plugs Inspect and replace spark plugs if necessary. Worn or defective spark plug wires Contact your dealer. Incorrect spark plug gap or heat range Set gap to specs or replace plugs. Loose electrical connections Check all connections and tighten them�...
Page 137
ELECTROMAGNETIC COMPATIBILITY STATEMENT ELECTROMAGNETIC COMPATIBILITY STATEMENT The electrical and electronic systems of this vehicle conform to the performance requirements of UNECE R10, and their construction do not cause excessive electromagnetic interference and are not unduly affected by electromagnetic interference. This equipment has been tested and found to comply with the limits of UNECE R10. These limits are designed to provide reasonable protection against harmful interference in terms of residential installation.
CFMOTO Limited Warranty Dear Customer, Thank you for purchasing a CFMOTO product, if any component on your vehicle is found to be defective in materials or workmanship within the terms and conditions of this Limited Warranty, the defective component will be repaired or replaced (at the option of CFMOTO) without charge for parts and/or labor at any authorized dealer located within the United States.
Page 139
2� WARRANTY LIMITATIONS: CFMOTO POWERSPORTS, Inc. provides warranty coverage for one (1) year on all parts and labor for all of its new CFMOTO ATVs. However, the following coverage, exceptions, and limitations apply to all CFMOTO vehicles: A� 30-DAY WARRANTY coverage applies to all new CFMOTO vehicles in relation to the vehicle’s: •...
Page 140
3� EXCLUSIONS FROM WARRANTY COVERAGE: Any damage resulting from the following acts or circumstances is not covered by the CFMOTO POWERSPORTS, Inc., Limited Warranty: • Fire • Collision • Theft • Unavoidable natural disasters • Improper storage or transportation • Failure or negligence in the performance of periodic vehicle maintenance •...
Page 141
5� TRANSFER OR CONTINUATION OF WARRANTY: This warranty is transferable only under the following conditions: • Transfer information must be provided to an authorized CFMOTO POWERSPORTS, Inc. dealer, who will then forward the information to CFMOTO POWERSPORTS, Inc.; • The complete model and serial number as shown on the original warranty document must be Provided�...
Page 142
8� CUSTOMER ASSISTANCE: Any questions or concerns regarding your CFMOTO vehicle or related products should be directed to an authorized CFMOTO dealer. However, if a dealer is unable to address customer concerns or a product issue, CFMOTO POWERSPORTS Customer Service can be contacted directly at (763) 398-2690 or by e-mail: info@cfmotousa.com.
Page 143
12� INTEGRATION: This limited warranty supersedes any and all oral, express, or written warranties, statements, or undertakings that may previously have been made, and contains the entire agreement of the parties with respect to the warranty of CFMOTO vehicles. Any and all warranties not contained in this Agreement are specifically excluded.
CALIFORNIA EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS INTRODUCTION: The California Air Resources Board (CARB) and CFMOTO Powersports, Inc. (CFMOTO) are pleased to explain the evaporative emissions control system warranty on your 2020 and later-model year off-highway recreation vehicles (OHRVs).
Page 145
As an owner, you are responsible for presenting your OHRV to a CFMOTO dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. As an OHRV owner, you should also be aware that CFMOTO may deny you warranty coverage if your OHRV or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.
U�S�A� EPA and CARB Emissions Control Limited Warranty This emissions limited warranty is in addition to the CFMOTO Powersports, Inc. standard limited warranty for your vehicle. CFMOTO Powersports, Inc. warrants that at the time it is first purchased, this emissions-certified vehicle is designed, built and equipped so it conforms to applicable U.S. Environmental Protection Agency (EPA) and the California Air Resource Board (CARB) emission regulations.
Page 147
For exhaust emissions, emission-related components include any engine parts related to the following systems: • Air-induction system (excludes filters) • Ignition system (excludes spark plugs) • Fuel system (excludes filters) • Exhaust gas recirculation systems The following parts are also considered emission-related components for exhaust emissions: •...
Page 148
THE REMEDIES SET FORTH IN THIS LIMITED WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY. CFMOTO POWERSPORTS, INC. SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE OR OTHER TORT OR OTHERWISE.
Page 149
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply if it is inconsistent with the controlling state law. This limited warranty excludes failures not caused by a defect in material or workmanship. This limited warranty does not cover damage due to accidents, abuse or improper handling, maintenance or use.
Noise Control System and Tampering Warranty time period: 1,865 miles (3000 km) Federal law prohibits the following acts or causing thereof: (1)The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or;...
Change of Ownership If you sell your vehicle, any valid remainder of the warranty can be transferred to the new owner. Please record the details of the exchange below and inform an authorized CFMOTO dealer: Change of Original Owner Owner Ownership Purchaser Owner Name...