Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for lamber LP6-dy
Summary of Contents for lamber LP6-dy
- Page 1 POT-WASHER LP6-dy LP8-dy LP6-dy-CVP-S LP8-dy-CVP-S INSTRUCTIONS MANUAL R00-2017...
-
Page 3: Declaration Of Conformity
DECLARATION OF CONFORMITY The following : LAMBER SRL – Via Italia 6 – 26855 Lodi Vecchio (LO) ITALY Declare under our responsibility that: Apparatus: Professional POT WASHER Trademark: LAMBER Manufacturer : LAMBER SRL Mod. for which this declaration refers to the conformity of the following standards: ... - Page 4 The directive mentioned above, to which make reference for further details, provides for punitive actions in case of illegal disposal of such waste. Lamber guarantees a percentage of recovery at least of 90% in medium weight for each equipment. The 80% - always as regards the medium weight- of recovered material is recycled or reused.
- Page 5 INDEX General notes pag. 06 Introduction and safety notes pag. 07 Learn to use the appliance pag. 08 First section - FOR THE USER pag. 09 Control panel pag. 10 Working and use pag. 11 Instructions before washing pag. 11 Washing pag.
-
Page 6: General Norms
GENERAL NORMS Thank You for purchasing our Pot-washing machine. Perfect washing-up results as far as hygiene concerns and a correct operation of the dishwashing machine can be assured only in case the instructions reported in the present manual are carefully followed. We hope the information reported in the present manual will be helpful to You. - Page 7 INTRODUCTION AND SAFETY NOTES INTRODUCTION - The machine is an Industrial Pot-washing machine. - Noise level of the machine: (Norms EN ISO 4871 and EN ISO 11204) <70 dB(A) PRELIMINARY OBSERVATION Carefully read the instructions reported in the present user manual, as it gives important indications about safety of installation, operation and maintenance: carefully keep the present manual for further consultations;...
- Page 8 Learn to use the appliance (only LP6/ LP6/L-dy CVP-S LP8/LP8/L-dy CVP-S Steam condenser ExtractableSteam condenser filter (only LP6/ LP6/L-dy CVP-S LP8/LP8/L-dy CVP-S Stainless steel Upper rotating washing Stainless steel Tank with slanting bottom Upper rotating rinsing ( cone 90°) Stainless steel Double skin with insulation 14mm Lower rotating rinsing (cone 90°) Stainless steel...
-
Page 9: Instructions For The User
INSTRUCTIONS FOR THE USER... -
Page 10: Control Panel
CONTROL PANEL Main switch Cycle pushbutton Interactive display Temperature data display Wash time selection pushbutton Programming pushbutton... -
Page 11: Turn On The Machine
"A" placed on the a subsequent Resins’ Washing. control panel (DIAGRAM.1). Attention: during tank filling don’t open the door You will see the serial number of the machine of the machine! followed by the logo Lamber. - Page 12 Attention! WASHING If during the loading phase, appears the message “BREAK TANK”, this means that you’re filling up Open the door of the machine and insert with water the rear Break Tank. the basket. . If after 5 minutes the data is still flashing in N.b.The display informs you when the top of the alternation with the inscription FILLING PHASE 1, machine is open.
- Page 13 Remove the basket and tilting it, shake it lightly to (only for machines with steam condenser CVP-S) bring down the remaing drops. Allow to dry the objets by evaporation, then remove them from At the end of the washing phase there is the automatically activating of the fan for suction of the basket, taking care not to touch the inside edge of the same.
- Page 14 “ON”, press the cycle “B” push-button for 3 again the push button “A” seconds, then closing the door, the machine will The logo Lamber will reappear and will then be able to not operate the wash cycle while maintaining start the function SELF-WASHING holding down the active heating functions.
- Page 15 (N.B. The word “REMOVE OVERFLOW” will Press the “B” button for 3 seconds and disappear only to the closing of the door) wait for the complete emptying of the tank; The discharge stops automatically after about Close the door of the machine; 2’,20”...
- Page 16 8-SALT OR PRODUCT CONTROL: List of automatic MESSAGES This message indicates salt lack inside the salt container (only for dishwasher with water On the display may appear some messages to softener) or liquid lack inside the descaling liquid, inform about the status of the cycle start of detergent and/or rinse aid dispensers.
- Page 17 The dishwasher stops working. List ALARMS! Switch off the machine by pressing ON/OFF pushbutton. BREAK TANK ALARM This indicates a fault in the operating system: (If possible check before if there is water inside lack of water mains, valve not functionning: Call the network or the overflow is in correct place.) Customer Service! Call the Technical Support Service!
- Page 18 OBJETS POSITIONING Warning ! Insert the baskets inside the Only use the baskets machine with the objets as supplied with the pot-washer shown in the picture. CLEARANCE To achieve optimal cleaning results, make sure that objets are correctly stored LP6: H max=620 mm inside the machine LP8: H max=620 mm CLP-70 cod.CC00091 (1x)
-
Page 19: Daily Maintenance
DAILY MAINTENANCE CLEANING PREVENTIVE MAINTENANCE Turn off the machine by pressing the switch “A” and drain the water from PRECAUTION CLEANING the tank by removing the overflow; INSTRUCTIONS IMPORTANT : Before carrying out the Please pay attention to the opening and cleaning maintenance operations,... - Page 20 DAILY CLEANING OF THE INTERIOR OF THE POT-WASHER Attention. Before carrying out cleaning the inside of the machine, make sure that there are no foreign objects that could damage the rusty steel inside the tank. The eventual rust particles could come from non- stainless steel dishes, from baskets or damaged water pipes not rust-proof.
- Page 21 Remove the tank filters Remove the frontal tank filter. Remove the overflow pipe Remose support Clean the pump filter by Clean the washing arm means of a brush Wipe with a cloth the tank Insert the central support . and check for any debris on the bottom.
- Page 22 Before insertion Remove the frontal tank filter. overflow check the presence silicon joint cod.0200304 After insert the overflow in his place Replace the lower washing Insert all tank filter in their Make sure is correctly in his place place Screw the lower rinse arm. Replace the s.s.disc cod.
- Page 23 Replace the upper wash arm Control the wash arm is in his place Keeping with a hand the Screw the upper rinse arm. Check that the wash and washing arm in place, screw rinse arms are free to rotate the s.s. disc cod.0201010 (upper and lower) ATTENTION! Daily...
- Page 24 DETERGENT and RINSE-AID Attention. During the use of chemicals is advisable to wear appropriate clothing, such as gloves and protectives glasses. It’s therefore important to consider some factors. Firsf of all, it is necessary to use only strongly anti-foaming Alkali and Chlore Products specific for industrial dishwasher, manufactured by Companies recognized as seriousness.
-
Page 25: Problems - Causes - Solutions
PROBLEMS - CAUSES - SOLUTIONS PROBLEMS CAUSES SOLUTIONS The machine doesn't catch Main switch is switched off; Turn ON the main switch; Power plug is not inserted Insert the power plug The water doesn't go in Water cock closed; Open water cock; The Overflow is not in place;... - Page 26 DESCALING When hard water is used you can find inside the machine and also on dishes calcareous sediments which must be removed both for hygienic and operating reasons by a descaling operation. Operating process and frequency of this intervention are suggested by your cleansing agent supplier who has suitable products, generally containing phosphoric acid.
- Page 27 USEFUL HINTS FOR STAINLESS STEEL MAINTENANCE Stainless steel is so called because it is not affected by oxidation; this dues its resistance to a thin molecular layer of oxide on the surface which protects againts further oxidation. There are, however, substances which can modify or destroy this layer, giving rise to corrosion: besides preventing the protective film of oxide from reforming, these substances corrode the stainless steel itself and can cause irreparable damage.
-
Page 29: Instructions For The Installer
INSTRUCTIONS FOR THE INSTALLER The following instructions are addressed to a qualified personnel, the only one authorised to carry out checks and repair, if any. The Manufacturer declines any responsibility in the case of interventions made by a non qualified personnel. -
Page 33: Second Section - For The Installer
Second Section - FOR THE INSTALLER During the installation, carry out a good machine levelling, which is a prerequisite for a correct operation. The Manufacturer cannot assume any responsability for any damage to persons or property deriving from the non-observance of the above-specified norms. For a correct installation see draw page 30/31 . -
Page 34: Water Connections
DUCT: Provide to bring close to the WATER CONNECTIONS machine a water duct with the above characteristics, terminating with a gate Carefully comply with any national or valve and with a male thread of ¾” Gas. regional regulations in force. WORKS TEMPERATURES Water installation must have the following characteristics:... -
Page 35: Detergent Dispenser
If there is the detergent pump installed by the characteristics of the installation. Lamber, data are as follows: Capacity: 1cc/SEC=3,6 Lit/H For the installation of the dispenser inside the Voltage: 230/50-60Hz... -
Page 36: Descaling Cycle
DESCALING CYCLE : The choice of a suitable cleansing agent is an essential condition if you want to obtain extremely good washing results as regards For programming, see section CONFIGURATION hygienic results. That’s why it’s important to USER TECHNICAL-PROGRAMMING consider some points. First of all only highly alkaline and chlorine-active antifoam products, The descaling cycle has a duration of about 35 especially made for industrial dish-washing... - Page 37 CHECK THE RINSE TANK HEATING List ALARMS! ATTENTION: if the dishwasher is in the washing phase (pump is functioning), the cycle will stop. BREAK TANK ALARM delete message press whatever It indicates an anomaly: lack of water from the pushbutton. net, solenoid valve not functioning.
- Page 38 - You are recommended to proceed with the cleaning of the dosage hoses and the detergent pump with water once a month. Failure to comply with these guidelines will render this guarantee invalid. Lamber disclaims any liability for consequential damage on the product.
- Page 39 KEYBOARD INTERACTIVE MEMBRANE LP6-LP8-dy-rev-15-ver-2-07 Machine OFF ON/OFF push-button "A" for 1 second when the machine is ON (logo LAMBER appears) (with the machine empty the display will show off after 10" seconds) (just with machine full) Machine ON ON/OFF push-button "A" for 1 second when the machine is in OFF (Temperature displayed) with the machine empty the display will indicate "door open"...
- Page 40 USER TECHNICAL-CONFIGURATION PROGRAMMING "+" Push-button and push-button enter "D" for 5 second with the machine FF and hood open cod. PIN 1000 To view the Unit of measure Unit of measure °C temperatures during temperatures during To confirm To confirm °F washing cycle press push-button...
- Page 41 Total Cycles (Number of Cycles performed) n°…… (not editable) To confirm Partial Cycles Reset Reset n° n …… yes/no yes/no To confirm To confirm ("yes" to reset value) Automatic Starting To confirm Time phase 2 Time To confirm Filling of the tank (10÷360") Rinsing 2 To confirm...
- Page 42 dos. Discaling dos.discaling To confirm Dosing time (0÷100%) for the times Discaling the table on the manual Without Drain pump this parameter is not Stand By To confirm The display will show the word ECONOMY AUTOMATIC OFF To confirm If YES, when the machine is not used for 1 hour, the same turn OFF completely Soft-start To confirm...
- Page 43 TWIN standard To confirm Name machine name machine 1 name machine 2 Key sound To confirm Exit At the end of the programming operations the machine turns off. Press push-button "A"...
-
Page 44: Connections Scheme
CONNECTIONS SCHEME BOILER Elements Brown Black Black Staples TANK Elements Brown Black Black Staples COL-L25-EK-display-2014... - Page 49 COMPONENTS LP6-dy LP8-dy PT850-dy cod.0300842 MEMBRANE KEYBOARD M1/M2 BASE optional Cnp-LP6/LP8-PT850-dy-display-2017...
- Page 50 SPECIFICATIONS - FRONTAL POT-WASHING MACHINES LP6-dy LP8-dy MODEL 885x965x1835 885x965x2035 DIMENSIONS l x w x h 20/12/8 20/12/8 WASHING CAPACITY baskets/H 3'-5'-7' 3'-5'-7' Min. WASH CYCLE Min. 700x700 700x700 BASKET SIZE WORK HEIGHT DAYLIGHT 400 V3/N~50Hz 400 V3/N~50Hz VOLTAGE 2x1500...