Page 1
PRE-WASH COMPACT UNIT PRL-C INSTRUCTIONS MANUAL REV.04-2016...
Page 3
DECLARATION OF CONFORMITY The following : LAMBER SRL – Via Italia 6 – 26855 Lodi Vecchio (LO) ITALY Declare under our responsibility that: Apparatus: COMPACT PRE-WASH UNIT WITH PUMP Trademark: LAMBER - Manufacturer : LAMBER SRL MODEL for which this declaration refers to the conformity of the following standards: ...
The directive mentioned above, to which make reference for further details, provides for punitive actions in case of illegal disposal of such waste. Lamber guarantees a percentage of recovery at least of 90% in medium weight for each equipment. The 80% - always as regards the medium weight- of recovered material is recycled or reused.
GENERAL SAFETY REGULATIONS This appliance in not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance (EN 60335-2-102/7.12).
Observe the safety notes indicated and the dosage recommendations for the use of chemicals. When using chemicals, wear protective clothing, gloves and goggles. Use only suitable products for industrial dishwashers directly recommended by Lamber. Do not mix cleaning products to avoid crystallization that could ruin the detergent dispenser.
PRL-C First Section - FOR THE USER The compact independent pre-wash unit allows to replace the hand prewashing usually carried out on the dirty dishes. Two strainer drawers with a high capacity allow to collect the dirt present on the dishes.
“A” in position OFF. Please note! The opening of the frontal strainer drawer of the PRL-C unit causes the stop only of the pre- wash pump. The rack conveyoring will continue and so the washing of the dishes in the main dishwasher won’t be stopped.
STARTING UP AND USE OF THE PRE- WASH UNIT For a unit directly connected to the machine! The independent pre-wash unit is connected to the main pull-through dishwasher. Remove the internal filters and eliminate the The tank water feeding of the pre-wash unit is dirt that has accumulate during the pre-wash.
AFTER WASHING OPERATIONS ATTENTION! Drain only for independent unit! PRECAUTION CLEANING At the end of the daily operations carry out the INSTRUCTIONS drain by turning the Selector switch “A” in position “drain” (lamp “D” lighted on) At the end of the drain turn the selector switch Attention.
Page 16
Remove also the main drawer (see picture) and rinse it with clean water. Disassemble the lower arm To remove the drawer completely from its housing it’s enough to grip the rear handle placed on the bottom of the drawer (see the following picture).
Page 17
Remove the filters F3 on the right and left position of the tank and rinse them with clean water. See the images for the right positioning of the filters.
Page 18
8 – Remove the pump suction filter F4 and rinse it with clean water. 9 –At the end of the cleaning, r eassemble the filter F3 in the right place (see draw) Remove the upper tank filters F2 and rinse them with clean water.
and the others filter F4,F2 and F1. 11– Clean the outside of the machine with a wet sponge. Never use water jets because, besides being dangerous, they can damage the electrical parts. Never use detergents, abrasive stuffs, rough sponges steel brushes.
MOTOR PROTECTION DEVICES SAFETY DEVICES Each motor is protected against short- The machine are equipped with a number circuits and current overload by automatic of devices in order to ensure the safety of magneto-thermal relays. the operator and of the appliance itself. Lamp "M"...
USEFUL HINTS OF STAINLESS STEEL MAINTENANCE Stainless steel is so called because it is not affected by oxidation,this is due to a thin molecular layer of oxide on the surface which protects againts further oxidation. There are, howevwr, substances which can modify or destroy this layer,giving rise to corrosion:besides preventing the protective film of oxide from reforming,these substances corrode the stainless steel itself and can cause irreparable damage.
INSTRUCTIONS FOR THE INSTALLER The following instructions are addressed to a qualified personnel, the only one authorised to carry-out checks and repair, if any. The Manufacturer declines any responsibility in the case of interventions made by a non qualified personnel.
PRL-C Second Section - FOR THE INSTALLER The following instructions are addressed to qualified personnel who is the only one authorized to carry out the inspections and the necessary repairs. The machine should be installed in “Normal” environment that is to say, indoors, free of dust, explosion-proof and adequately lit and well aired.
ELECTRICAL CONNECTION WARNING: Danger to life due to live components! During all electrical operations, disconnect the machine from the network and verify the absence of power. The machine and its accessories must be connected in accordance with local regulation, by a company that is specialized in electrical installation authorized by the competent authorities.