lamber LP8/L-dy Instruction Manual
  1. Manuals
  2. Brands
  3. lamber Manuals
  4. Washer
  5. LP8/L-dy
  6. Instruction manual
lamber LP8/L-dy Instruction Manual

lamber LP8/L-dy Instruction Manual

Hide thumbs Also See for LP8/L-dy:
Table of Contents

Advertisement

Quick Links

Download this manual
REV.07-2016
POT WASHING
MACHINES
LP8/L-dy
INSTRUCTIONS
INSTRUCTIONS
MANUAL
MANUAL

Advertisement

Table of Contents
loading

Related Manuals for lamber LP8/L-dy

Summary of Contents for lamber LP8/L-dy

  • Page 1 POT WASHING MACHINES LP8/L-dy INSTRUCTIONS INSTRUCTIONS MANUAL MANUAL REV.07-2016...

  • Page 3: Declaration Of Conformity

    DECLARATION OF CONFORMITY The following : LAMBER – Via Italia 6 – 26855 Lodi Vecchio (LO) ITALY Declare under our responsibility that: Apparatus: Professional POT WASHER Trademark: LAMBER Manufacturer : LAMBER Mod. for which this declaration refers to the conformity of the following standards: ...
  • Page 4 The directive mentioned above, to which make reference for further details, provides for punitive actions in case of illegal disposal of such waste. Lamber guarantees a percentage of recovery at least of 90% in medium weight for each equipment. The 80% - always as regards the medium weight- of recovered material is recycled or reused.
  • Page 5 INDEX General notes pag. 06 Introduction and safety notes pag. 07 Learn to use the appliance pag. 08 First section - FOR THE USER pag. 09 Control panel pag. 10 Working and use pag. 11 Instructions before washing pag. 11 Washing pag.

  • Page 6: General Norms

    GENERAL NORMS Thank You for purchasing our Pot-washing machine. Perfect washing-up results as far as hygiene concerns and a correct operation of the dishwashing machine can be assured only in case the instructions reported in the present manual are carefully followed. We hope the information reported in the present manual will be helpful to You.
  • Page 7 INTRODUCTION AND SAFETY NOTES INTRODUCTION - The machine is an Industrial Pot-washing machine. - Noise level of the machine: <70 dB(A) (Norms EN ISO 4871 and EN ISO 11204) PRELIMINARY OBSERVATION Carefully read the instructions reported in the present user manual, as it gives important indications about safety of installation, operation and maintenance: carefully keep the present manual for further consultations;...
  • Page 8 Learn to use the appliance LP6/L-dy-LP8/L-dy CVP-S (only Steam condenser ExtractableSteam condenser filter LP6/L-dy-LP8/L-dy CVP-S (only Stainless steel Upper rotating washing Stainless steel Tank with slanting bottom Upper rotating rinsing ( cone 90°) Stainless steel Double skin with insulation 14mm Lower rotating rinsing (cone 90°)

  • Page 9: Instructions For The User

    INSTRUCTIONS FOR THE USER...

  • Page 10: Control Panel

    CONTROL PANEL Main switch Cycle pushbutton Interactive display Wash time selection pushbutton Programming pushbutton Dis.1 09-2013...

  • Page 11: First Section - For The User

    - While the machine is running, never open the door too rapidly; - Only use specific anti-frothing detergents. You will see the serial number of the machine INSTRUCTIONS BEFORE WASHING followed by the logo Lamber. EFORE STARTING THE WORKING OPERATION MAKE SURE THAT Please pay attention to the opening and closing of the door of the machine.
  • Page 12 Attention: during tank filling don’t open the door Place the objets in the basket minding to of the machine! previously remove all solid waste and fat. N.B.: When the objects to be washed present Attention! burnt crusts, or a long time is elapsed from If during the loading phase, appears the message cooking up tothe time of washing, it is necessary “BREAK TANK”, this means that you’re filling up...
  • Page 13 To temporarly pause the cycle, simply open the ACHIEVEMENTS hood of the dishwasher.Closing it, the cycle will start again at exactly the point were it was Any deficiency in the washing process is interrupted. obvious when dirty residuals are visible. Any It is possible at any time to stop the wash cycle by halos might be caused by an insufficient rinsing: simply pressing the button again cycle “B”...
  • Page 14 “A” and then pressing it again to to turn off again the push button “A” The logo Lamber will reappear and will then be able to After drainig, the machine will turn off start the function SELF-WASHING holding down the completely (display OFF).
  • Page 15 For an average water limestone is recommended until it reaches the programmed temperature, at cycle activation at least once a week. which may start the rinsing phase. The frequency may vary depending on type of water. 6-REMOVE OVERFLOW : This indicates that the overflow has to be removed to perform the selected operations (self- keep button machine «OFF»...
  • Page 16 OBJETS POSITIONING Warning ! Insert the baskets inside the Only use the baskets machine with the objets as supplied with the pot-washer shown in the picture. CLEARANCE To achieve optimal cleaning results, make sure that objets are correctly stored LP6: H max=620 mm inside the machine LP8: H max=620 mm CLP-70 cod.CC00091 (1x)

  • Page 19: Daily Maintenance

    DAILY MAINTENANCE CLEANING PREVENTIVE MAINTENANCE Turn off the machine by pressing the switch “A” and drain the water from PRECAUTION CLEANING the tank by removing the overflow; INSTRUCTIONS IMPORTANT : Before carrying out the Please pay attention to the opening and cleaning maintenance operations,...
  • Page 20 DAILY CLEANING OF THE INTERIOR OF THE DISHWASHER Attention. Before carrying out cleaning the inside of the machine, make sure that there are no foreign objects that could damage the rusty steel inside the tank. The eventual rust particles could come from non- stainless steel dishes, from baskets or damaged water pipes not rust-proof.
  • Page 21 Remove the tank filters Remove the frontal tank filter. Remove the overflow pipe Remose support Clean the pump filter by Clean the washing arm means of a brush Wipe with a cloth the tank Insert the central support . and check for any debris on the bottom.
  • Page 22 Before insertion Remove the frontal tank filter. overflow check the presence silicon joint cod.0200304 After insert the overflow in his place Replace the lower washing Insert all tank filter in their Make sure is correctly in his place place Screw the lower rinse arm. Replace the s.s.disc cod.
  • Page 23 Replace the upper wash arm Control the wash arm is in his place Keeping with a hand the Screw the upper rinse arm. Check that the wash and washing arm in place, screw rinse arms are free to rotate the s.s. disc cod.0201010 (upper and lower) ATTENTION! Daily...
  • Page 24 DETERGENT and RINSE-AID Attention. During the use of chemicals is advisable to wear appropriate clothing, such as gloves and protectives glasses. It’s therefore important to consider some factors. Firsf of all, it is necessary to use only strongly anti-foaming Alkali and Chlore Products specific for industrial dishwasher, manufactured by Companies recognized as seriousness.

  • Page 25: Problems - Causes - Solutions

    PROBLEMS - CAUSES - SOLUTIONS PROBLEMS CAUSES SOLUTIONS The machine doesn't catch Main switch is switched off; Turn ON the main switch; Power plug is not inserted Insert the power plug The water doesn't go in Water cock closed; Open water cock; The Overflow is not in place;...
  • Page 26 DESCALING When hard water is used you can find inside the machine and also on dishes calcareous sediments which must be removed both for hygienic and operating reasons by a descaling operation. Operating process and frequency of this intervention are suggested by your cleansing agent supplier who has suitable products, generally containing phosphoric acid.
  • Page 27 USEFUL HINTS FOR STAINLESS STEEL MAINTENANCE Stainless steel is so called because it is not affected by oxidation; this dues its resistance to a thin molecular layer of oxide on the surface which protects againts further oxidation. There are, however, substances which can modify or destroy this layer, giving rise to corrosion: besides preventing the protective film of oxide from reforming, these substances corrode the stainless steel itself and can cause irreparable damage.

  • Page 29: Instructions For The Installer

    INSTRUCTIONS FOR THE INSTALLER The following instructions are addressed to a qualified personnel, the only one authorised to carry out checks and repair, if any. The Manufacturer declines any responsibility in the case of interventions made by a non qualified personnel.

  • Page 31: Second Section - For The Installer

    Second Section - FOR THE INSTALLER During the installation, carry out a good machine levelling, which is a prerequisite for a correct operation. The Manufacturer cannot assume any responsability for any damage to persons or property deriving from the non-observance of the above-specified norms. For a correct installation see draw page 30/31 .

  • Page 32: Water Connections

    DUCT: Provide to bring close to the WATER CONNECTIONS machine a water duct with the above characteristics, terminating with a gate Carefully comply with any national or valve and with a male thread of ¾” Gas. regional regulations in force. WORKS TEMPERATURES Water installation must have the following characteristics:...

  • Page 33: Detergent Dispenser

    If there is the detergent pump installed by Lamber, data are as follows: Capacity: 1cc/SEC=3,6 Lit/H Voltage: 230/50-60Hz The suction tube of liquid detergent has to be passed through the opening spot on the right side...

  • Page 34: Descaling Cycle

    DESCALING CYCLE : hygienic results. That’s why it’s important to consider some points. First of all only highly alkaline and chlorine-active antifoam products, For programming, see section CONFIGURATION especially made for industrial dish-washing USER TECHNICAL-PROGRAMMING machines, must be used and they must be produced by well-known reliable Firms.
  • Page 35 - You are recommended to proceed with the cleaning of the dosage hoses and the detergent pump with water once a month. Failure to comply with these guidelines will render this guarantee invalid. Lamber disclaims any liability for consequential damage on the product.
  • Page 36 KEYBOARD INTERACTIVE MEMBRANE Machine OFF ON/OFF push-button "A" for 1 second when the machine is ON (logo LAMBER appears) (with the machine empty the display will show off after 10" seconds) (just with machine full) Machine ON ON/OFF push-button "A" for 1 second when the machine is in OFF (Temperature displayed) with the machine empty the display will indicate "door open"...
  • Page 37 USER TECHNICAL-CONFIGURATION PROGRAMMING "+" Push-button and push-button enter "D" for 5 second with the machine FF and hood open cod. PIN 1000 To view the Unit of measure Unit of measure °C temperatures during temperatures during To confirm To confirm °F washing cycle press push-button...
  • Page 38 Total Cycles (Number of Cycles performed) n°…… (not editable) To confirm Partial Cycles Reset Reset n° n …… yes/no yes/no To confirm To confirm ("yes" to reset value) Automatic Starting To confirm Time phase 2 Time To confirm Filling of the tank (10÷360") Rinsing 2 To confirm...
  • Page 39 dos. Rinsing dos.Rinsing To confirm Dosing time (0÷100%) for the times dispenser of rinsing the table on the manual dos. Discaling dos.discaling To confirm Dosing time Dosing time (0÷100%) (0÷100%) for the times for the times Discaling the table on the manual Without Drain pump this parameter is not Stand By...

  • Page 40: Connections Scheme

    CONNECTIONS SCHEME BOILER Elements Brown Black Black Staples TANK Elements Brown Black Black Staples COL-L25-EK-display-2014...
  • Page 46 SPECIFICATIONS - FRONTAL POT-WASHING MACHINES MODEL LP6/L-dy LP6/L-dy-CVP-S LP8/L-dy LP8/L-dy CVP-S 885x965x1835 885x965x2010 885x965x2035 885x965x2210 DIMENSIONS l x w x h 30/20/15 30/20/15 30/20/15 30/20/15 WASHING CAPACITY baskets/H 2'-3'-4' 2'-3'-4' 2'-3'-4' 2'-3'-4' Min. WASH CYCLE 700x700 700x700 700x700 700x700 BASKET SIZE...
  • Page 48 Via Italia, 6 - 26855 Lodi Vecchio (LO) Italy Tel. (0371) 753202 - 754248-9 Fax (0371) 752928 www.lamber.it - e-mail: info@lamber.it...

Table of Contents